Moxa V2406-W7E [2/2] Configuring the ethernet interface
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Moxa V2406-W7E [2/2] Configuring the ethernet interface

Moxa V2426-T-XPE [2/2] Configuring the ethernet interface
– 4 – – 5 – – 6 –
www.moxa.com/support
The Americas:
+1-714-528-6777 (toll-free: 1-888-669-2872)
Europe:
+49-89-3 70 03 99-0
Asia-Pacific:
+886-2-8919-1230
China:
+86-21-5258-9955 (toll-free: 800-820-5036)
2014 Moxa Inc., All Rights Reserved
from the ground screw to the grounding surface prior to connecting
the power. Please note that these products are intended to be
mounted to a well-grounded mounting surface, such as a metal
panel
V2406/V2426
SG: The Shielded Ground (sometimes called
Protected Ground) contact is the central pin of
the power input connector
.
Connect the SG wire
to an appropriate grounded metal surface.
V2422
SG: The Shielded Ground (sometimes called
Protected Ground) contact is the
left-most
pin of
the power input connector
.
Connect the SG wire
to an appropriate grounded metal surface.
VGA and DVI Outputs
The V2406/2422/2426 comes with a D-Sub 15-pin female
connector for a VGA monitor; it also comes with a DVI-I connector
for the DVI display. These output interfaces are all located on the
front panel. Use the proper cable to connect.
PS/2 Port
The V2406/2422/2426 embedded computer comes with a PS/2
mini-DIN connector to connect to a PS/2 keyboard and PS/2
mouse. Use the Y-type cable to convert the mini-DIN connector
into two 6-pin mini-DIN connectors to connect both a PS/2
keyboard and PS/2 mouse at the same time. You may also use the
USB ports to connect your USB-based keyboard and mouse. Please
note that without a Y-type cable, the PS/2 connector on the
V2406/2422/2426 can only work with a PS/2 keyboard. A PS/2
mouse will not function when directly connected to the PS/2
connector on the V2406/2422/2426 embedded computer.
CompactFlash Slot
The V2406/2422/2426 has a CompactFlash slot located on the
front panel for storage expansion. It supports CF Type-I/II with
DMA mode. To install a CompactFlash card, remove the outer
cover, and then insert the CF card in the socket. When finished,
push the cover into the socket and fasten the screws.
USB Hosts
The V2406/2426 has one USB port with an M12 connector on the
front panel, and two USB ports with type A connectors on the rear
panel. For the V2422, four USB ports are located on the front panel,
two on the rear panel, and all come with type A connectors. These
USB ports can be used to connect flash disks for storing large
amounts of data.
Expansion Module Slot
The V2422/V2426 comes with two expansion slots that can
connect different communication modules, such as a 2-port CAN
module, a wireless communication module, an 8-DI/8-DO module,
and a 2-port serial module.
Ethernet Ports
V2406/2426
Two 10/100 Mbps Ethernet ports using M12
connectors are located on the front
panel.
See the following pin assignments.
V2422
Two 10/100
/1000
Mbps Ethernet ports with
RJ45
connectors are located on the front
panel. See the following pin assignments.
Serial Ports
The serial ports use DB9 connectors. Each port can be configured
by software for RS-232, RS-422, or RS-485. The pin assignments
for the ports are shown in the following table:
Pin
RS-232
RS-485
(4-wire)
RS-485
(2-wire)
1
DCD
TxDA(-)
–
2
RxD
TxDB(+)
–
3
TxD
RxDB(+)
DataB(+)
4
DTR
RxDA(-)
DataA(-)
5
GND
GND
GND
6
DSR
–
–
7
RTS
–
–
8
CTS
–
–
DI/DO
The V2406/2426 comes with a 6-ch digital input and 2-ch digital
output (4 DI/4 DO for V2422) in the terminal block connectors.
Audio Interface
The V2406/2422/2426 comes with an audio input and an audio
output, allowing users to connect a speaker or an earphone
Reset Button
Press the “Reset Button” on the rear panel of the computers to
reboot the system automatically. The Ready LED will blink on and
off for the first 5 seconds, and then maintain a steady glow once
the system has rebooted.
Real-time Clock
The V2406/2422/2426’s real-time clock is powered by a lithium
battery. We strongly recommend that you do not replace the
lithium battery without help from a qualified Moxa support
engineer. If you need to change the battery, contact the Moxa RMA
service team. Please note that there is a risk of explosion if
the battery is replaced by an incorrect type of battery.
Powering on the V2406/2422/2426
To power on the V2406/2426, connect the power cable to the
V2406/2426’s M12 power connector (located at the rear panel).
For the V2422, connect the power cable to the terminal block
connector (located at the rear panel). Press the power button to
turn on the computer. Note that the Shielded Ground wire should
be connected to the central pin of the connector. It takes about 30
seconds for the system to boot up. Once the system is ready, the
Power LED will light up.
Configuring the Ethernet Interface
Linux users should follow these steps:
Enter the following commands to edit the interfaces file:
#ifdown –a
//Disable LAN1/LAN2 interface first, before you
reconfigure the LAN settings. LAN 1 = eth0, LAN 2= eth1,
#vi /etc/network/interfaces
//check the LAN interface first//
After the boot settings of the LAN interface have been modified,
use the following command to activate the LAN settings
immediately:
#sync; ifup –a
XPE users should follow these steps.
1. Go to Start Network Connections.
2. Right-click Network Connections, click Properties, select
Internet Protocol (TCP/IP), and then click Properties.
3. Click OK after inputting the proper IP address and netmask.
W7E users should follow these steps:
1. Go to Start
->
Control Panel-> Network and Internet ->
View network status and tasks -> Change adapter
setting.
2. In the screen of Local Area Connection Properties, click
Internet Protocol (TCP/IP) and then select Properties.
Select Internet Protocol Version 4, and then click
Properties.
3. Click OK after inputting the proper IP address and netmask.

Содержание

Похожие устройства

Скачать