M-Audio EQMan [10/31] Drivers
10
EQMan Software
The EQMan requires software in order to be a useful tool. There are
three groups of software included with the EQMan: Diagnostics,
Windows Remote Control, and the Windows drivers. Diagnostic
software is discussed in the Installation part of this manual, so this
section will address the operation and relation of the other software
items.
Drivers
MIDI application software communicates with the EQMan via software
“drivers.” A software driver handles the hardware-specific details of the
EQMan and frees the MIDI application from having to know the
“specifics” of the hardware. If an EQMan driver is not installed, most
applications will not be able to manipulate or control the EQMan in any
way.
NOTE: The DOS diagnostics supplied with the EQMan have their own
EQMan “drivers” built-in and therefore can control the EQMan without
having to install other specific drivers beforehand.
On the included EQMan Drivers and Utilities diskette, Midiman
supplies the EQMan Windows drivers. These drivers enable the use of
the EQMan with Windows 3.1/3.11 and Windows 95 programs that
comply with the Windows Multimedia driver standards.
IMPORTANT: The EQMan Windows software drivers must be
installed in order for the EQMan to be used effectively with Windows
applications.
If you encounter problems using the EQMan with Windows, verify that
the EQMan Windows driver is installed. In Windows this can be done
via the Windows Control Panel. For further information on setting up
drivers under Windows, see the Windows Driver Operation section
below.
Because Windows software and DOS software behave differently, DOS
applications can not rely on the same set of drivers as Windows.
Instead each DOS application requires its own unique (and usually
proprietary) software driver for each hardware device. Consequently, the
EQMan can only be used with a DOS program if a specific EQMan
driver is written for that program. Please contact the developer of your
favorite DOS-based application for availability of EQMan driver
support.
Windows Remote Control Software
Содержание
- Error no table of contents entries found 1
- Fcc radio and television interference statement for a class b device 1
- Imjeqman 1
- Table of contents 1
- Introduction 2
- Eqman features 3
- Main in jack 3
- Aux in jack 4
- Fig 0 here 4
- Main out jack 4
- Address configuration 5
- Hardware installation 5
- Address jumper assignments 6
- Address jumper block position hex 1 2 3 4 5 6 7comments 6
- Factory default jumper settings 6
- The following diagram shows the address jumper blocks on the eqman the factory default address is 300h 6
- The program findport exe does its best to determine port addresses available for use with the eqman card choose one of the free addresses reported by findport and use the chart below to set the eqman address jumpers to that address it s also a good idea to write down the selected address as well as some alternates you may need these addresses later to run the diagnostics and install the eqman windows driver 6
- Diagnostic software 7
- Physical installation 7
- Drivers 10
- Eqman software 10
- Windows remote control software 10
- Windows 3 3 1 driver installation 11
- Installing the remote control software 12
- Windows 95 driver installation 12
- Windows driver operation 12
- Advanced driver setup 13
- Driver setup from windows control panel 13
- Control status bar 15
- Remote control software operation 15
- Slider bars and volume faders 15
- The file button 16
- The rom button 16
- The options button 17
- The current program status 18
- The flat button 18
- The lock button 18
- The map button 19
- Configuring windows applications to use eqman 20
- Midi control of eqman 20
- Some general thoughts about eq 23
- Troubleshooting 25
- Appendix midi implementation 27
- Dump all request requests the current settings of all eq bands and both volume controls plus the contents of all eqman rom programs the response is several sysex messages sixteen one rom program data messages followed by one current eq volume data message 28
- F0h 00h 01h 05h 01h 00h 01h 00h 0nh 42h 0ph f7h where n is midi channel 0 5 7fh all p is the rom program number 0 6 28
- F0h 00h 01h 05h 01h 00h 01h 00h 0nh 43h f7h where n is midi channel 0 5 7fh all 28
- Identity message identifies the midi device as an eqman 28
- The following system exclusive message is transmitted by the eqman in response to an identity request sysex message 28
- The following system exclusive message s may be written to the eqman or transmitted by the eqman in response to a request 28
- Current eq volume data message contains current settings of the eq bands and volumes for eq gain codes see table 1 below 29
- One rom program data message contains current settings of the specified eqman rom program for eq gain codes see table 1 below if the program name is less than 16 characters pad the end with 0 s 29
- Ch 12 db 0ah 10 db 08h 8 db 06h 6 db 04h 4 db 02h 2 db 00h 0 db 7eh 2 db 7ch 4 db 7ah 6 db 78h 8 db 76h 10 db 74h 12 db 30
- Table 1 eq gain codes for midi system exclusive messages 30
- Limited lifetime warranty 31
Похожие устройства
- JVC GR-DVL150 Инструкция по эксплуатации
- HP Mini 110-3604er LN004EA Инструкция по эксплуатации
- Proma TFS-75/30 25007530 Инструкция по эксплуатации
- Polaris PCDH 1115 Инструкция по эксплуатации
- M-Audio Duo USB Инструкция по эксплуатации
- JVC GR-DVL145 Инструкция по эксплуатации
- HP G5215ru XS528EA Инструкция по эксплуатации
- Proma TFS-90/30 25009030 Инструкция по эксплуатации
- Polaris PCDH 0715 Инструкция по эксплуатации
- M-Audio Dman PCI Инструкция по эксплуатации
- HP G5325ru LF941EA Инструкция по эксплуатации
- JVC GR-DVL120 Инструкция по эксплуатации
- Polaris PCH 1074W Инструкция по эксплуатации
- Electrolux EWH 30 Centurio H Инструкция по эксплуатации
- M-Audio Dman 2044 Инструкция по эксплуатации
- HP Pavilion p6751ru LN753EA Инструкция по эксплуатации
- Panasonic DMC-FS16EE-R Инструкция по эксплуатации
- JVC GR-DVL109 Инструкция по эксплуатации
- Polaris PCH 1575W Инструкция по эксплуатации
- Baxi SR 515 SL Инструкция по эксплуатации