![Autel Autolink AL419 [63/66] Audio tone interpretation](/img/pdf.png)
Autel Autolink AL419 [63/66] Audio tone interpretation
![Autel Autolink AL419 [63/66] Audio tone interpretation](/views2/1200926/page63/bg3f.png)
62
“INC” -- Indicates that a particular monitor being checked
has not completed its diagnostic testing.
“N/A” -- The monitor is not supported on the vehicle.
The LED and audio tone indications are interpreted as below:
LED Interpretation
The green and red LEDs provide an easy way to check if
emission-related monitoring systems complete their self-diagnostic
testing.
1) GREEN LED – Your vehicle is Ready. Indicates that engine
systems are “OK” and operating normally (the number of
Monitors supported by the vehicle which have run and
performed their self-diagnostic testing is in the allowed limit).
2) RED LED –Your vehicle is Not Ready. Indicates that the
number of Monitors supported by the vehicle which have run
and performed their self-diagnostic testing is out of the allowed
limit.
Audio Tone Interpretation
The audio tone could be configured according to the I/M Readiness
Status. This function is invaluable when performing diagnostics and
driving at the same time , or working in bright areas where LED
illumination alone is not sufficient.
LED Light
Audio Tone
Beep Interval
Green LED
Two long beeps
2 minutes
Red LED
No beep
Содержание
- Table of contents 1
- Safety precautions and warnings 2
- Diagnostic trouble codes dtcs 3
- General information 3
- On board diagnostics obd ii 3
- Dtc example 4
- Location of the data link connector dlc 4
- P 0 2 0 2 4
- Obd ii readiness monitors 5
- Obd ii monitor readiness status 6
- Obd ii definitions 7
- Obd ii modes of operation 8
- Tool description 11
- Using the scan tool 11
- Accessories included 13
- Navigation characters 13
- Specifications 13
- Dtc lookup 14
- Keyboard 14
- System setup 16
- To enter the setup menu 16
- Configure monitors 17
- Language setup 17
- Spark ign required monitors 18
- Compression ign required monitors 19
- Unit of measure 19
- Key beep set 20
- Status beep set 21
- Tool self test 21
- Update mode 23
- Vehicle coverage 25
- Operating error 26
- Product troubleshooting 26
- Vehicle linking error 26
- Led lamps not working 27
- Scan tool doesn t power up 27
- Review data 28
- Obdii diagnostics 30
- Reading codes 32
- Erasing codes 34
- Live data 36
- Viewing data 36
- Figure 5 7 40
- Figure 5 8 40
- If you decide to deselect these items press ok if you decide 40
- If you want to deselect all marked items or select all items 40
- Indicates sequence of highlighted item and x are the order that the parameters are selected and will be displayed 40
- Not to press esc or use the left right scroll button to select no to continue pid selections 40
- Press the left button a message comes up to ask for your confirmation 40
- Press the ok button to view selected pids on screen 40
- The number x to the upper right corner of the screen 40
- Recording data 41
- Current test will be stored in a temporary cache 42
- Figure 5 0 42
- Figure 5 1 42
- Figure 5 2 42
- If data from previously tested vehicle is not erased data from 42
- Use the up down scroll button to select a memory location and press the ok button 42
- Use the up down scroll button to select a trigger mode and press the ok button 42
- Drive till a dtc is detected when dtc trigger is selected if no 44
- Dtcs are detected press esc to exit recording 44
- Figure 5 5 44
- Figure 5 6 44
- Indicates the maximum frames that can be recorded and the number of recorded frames 44
- The number x x to the upper right corner of the screen 44
- The scan tool keeps recording pid data until user presses the esc button selected memory location is full or it completes recording a message prompting to playback data shows on the screen 44
- Wait for dtc to trigger recording or press ok to start recording figure 5 6 44
- Playback data 47
- Viewing freeze frame data 48
- Retrieving i m readiness status 49
- A retrieve i m readiness status with one click i m 50
- Readiness key 50
- B retrieve i m readiness status in typical way 53
- Viewing vehicle information 56
- Code breaker 57
- General information 59
- Ready test 59
- Ready test application 59
- As post repair diagnostic tool 60
- As pre check diagnostic tool 61
- Led and tone interpretation 62
- Audio tone interpretation 63
- Led interpretation 63
- Print data 64
- Limited one year warranty 66
- Service procedures 66
- Warranty and service 66
Похожие устройства
- Autel Autolink AL619 Руководство пользователя
- Autel Autolink AL319 Руководство пользователя
- Autel Autolink AL301 Руководство пользователя
- Autel MaxiCheck DPF Reset Руководство пользователя
- Autel AutoLink AL539B Руководство пользователя
- Autel MaxiTPMS TS401 Руководство пользователя
- Autel MaxiCheck PRO Руководство пользователя
- Autel MaxiCheck Oil Light/Service Reset Руководство пользователя
- Autel MaxiCheck EPB Руководство пользователя
- Autel Maxivideo MV201 8.5 мм Руководство пользователя
- Autel Maxivideo MV400 5.5 мм Руководство пользователя
- Autel Maxivideo MV400 8.5 мм Руководство пользователя
- Coolfort CF-1216 Инструкция по эксплуатации
- Coolfort СF-1221 Инструкция по эксплуатации
- Coolfort CF-0525GY Инструкция по эксплуатации
- Cremesso Compact Automatic Burgundy Red Инструкция по эксплуатации
- Cremesso LM 600 Инструкция по эксплуатации
- Cuckoo CMC-CHSS1004F Инструкция по эксплуатации
- Defender Optimum MS-125 Nano Инструкция по эксплуатации
- Defender Game Racer Turbo GT Инструкция по эксплуатации
Скачать
Случайные обсуждения