![M-Audio DIO2448 [5/24] Quick guide to getting started](/img/pdf.png)
M-Audio DIO2448 [5/24] Quick guide to getting started
![M-Audio DIO2448 [5/24] Quick guide to getting started](/views2/1020095/page5/bg5.png)
5
The DiO 2448 Adapter Card
1. Coaxial S/PDIF Input: This RCA connector receives a S/PDIF stereo
signal from an external coaxial S/PDIF device.
2. Coaxial S/PDIF Output: This RCA connector transmits a S/PDIF stereo
signal to an external coaxial S/PDIF device.
3. Optical S/PDIF Input: This TOSlink connector receives an optical
S/PDIF stereo signal from an external optical S/PDIF device.
4. Optical S/PDIF Output: This TOSlink connector transmits an optical
S/PDIF stereo signal to an external optical S/PDIF device.
5. Analog Audio Outputs (Left & Right): These RCA connectors carry the
left and right line-level signals to an external monitoring or mix-down
device. The signal levels of these outputs are compatible with most
consumer gear.
6. Internal CD-ROM headers, Analog: These headers (connectors) accept
analog line-level audio from a CD-ROM player or similar source internal
to the computer. Only one of these headers may be in use at one time.
7. Internal CD-ROM header, Digital: This header (connector) accepts a
digital audio S/PDIF signal from a CD-ROM player or similar source
internal to the computer. This header is wired in parallel to the coaxial
S/PDIF input. Therefore only one of these connectors may be used at a
time.
Quick Guide to Getting Started
Here is a list of the steps required to get your DiO 2448 up and running:
1. Physically install the card in your computer (see ‘Hardware
Installation’).
2. Start Windows and allow Windows’ Plug-and-Play to prompt you for
the DiO 2448 drivers via the Add New Hardware wizard.
3. Install drivers and support software (see ‘Driver & Software
Installation’).
4. Configure your digital recording software to select the DiO 2448 ports as
its active audio input and output devices (see ‘Using DiO 2448 with
Software Applications’ and also your applications software manual).
5. Hook your digital audio gear up to the DiO 2448 (see ‘Typical DiO 2448
Setup’).
Содержание
- Delta dio 2448 manual 1
- Table of contents 1
- Introduction 2
- Minimum system requirements 2
- Product features and specifications 2
- What s in the box 2
- About the dio 2448 3
- Basically the dio 2448 appears to your software as a stereo input stereo output 2x2 audio card there are three inputs to the card that may be recorded optical s pdif coaxial s pdif and internal cd rom s pdif as you can see from the dio 2448 block diagram the optical and coaxial s pdif streams are merged into one audio stream this is not a true digital mixer but instead a non intelligent merger that combines the raw data streams therefore only one of these jacks should be connected to an active signal at a time note also the cd rom s pdif header is wired directly to the coaxial s pdif jack in most cases utilizing the internal cd rom s pdif header will prevent you from using the optical and coaxial s pdif inputs therefore this header is primarily for using your dio 2448 and computer as a dedicated cd rom recording station and not for recording from external s pdif devices 3
- Control panel options 3
- The dio 2448 inputs and outputs support digital audio streams as wide as 24 bits the highest resolution available at this time of printing at sample rates of up to 48khz the dio 2448 s pdif inputs may record a digital signal from your dat minidisc cd player or external a d converter the dio 2448 s pdif and analog outputs may be used to monitor the incoming s pdif signal or to output digital audio from your software applications below is a simplified block diagram of the dio 2448 please reference this diagram while reading the remainder of this section 3
- Quick guide to getting started 5
- The dio 2448 adapter card 5
- Hardware installation 6
- Windows 98 95 driver software installation 6
- Windows 98 installation 6
- Windows 95 installation 7
- Windows driver configuration 9
- Dio 2448 control panel software 10
- Using the dio 2448 with your software applications 10
- Windows sound system 12
- In this example we ll connect a dat to the dio 2448 coaxial s pdif input using a coaxial cable typically rca to rca type 75 ohm impedance we ll also hook the analog outputs of the dio 2448 to a sound system for monitoring purposes a setup like this may be used if you were transferring 13
- Now that we ve visited the dio 2448 control panel and wss mixer let s look at a setup that involves a typical transfer of information from dat to computer and then computer to dat 13
- The middle fader wave output controls the level of the wav software playback prior to the master volume fader the rightmost fader cd audio controls the monitor level of the analog cd rom input again prior to the master volume fader 13
- Typical dio 2448 setup 13
- Transferring from dat to dio 2448 14
- Troubleshooting 17
- Troubleshooting tips for frequently asked questions 20
- Lifetime limited warranty 22
Похожие устройства
- Panasonic DMC-TZ18EE-K Инструкция по эксплуатации
- HP 310-1110ru XT030EA Инструкция по эксплуатации
- JVC GR-DVL107 Инструкция по эксплуатации
- Polaris PCH 1071 Инструкция по эксплуатации
- Jet DDS-237 Инструкция по эксплуатации
- M-Audio DigiPatch Инструкция по эксплуатации
- Panasonic DMC-FS35EE-K Инструкция по эксплуатации
- HP Omni 200-5310ru XT025EA Инструкция по эксплуатации
- JVC GR-DVL100 Инструкция по эксплуатации
- Panasonic AJ-SPD850 Инструкция по эксплуатации
- M-Audio Delta TDIF Инструкция по эксплуатации
- Timberk SWH RS1 100 V Инструкция по эксплуатации
- Polaris PCH 1572 Инструкция по эксплуатации
- HP LaserJet P1102w (CE657A) Инструкция по эксплуатации
- Panasonic DMC-FS16EE-S Инструкция по эксплуатации
- JVC GR-DV900 Инструкция по эксплуатации
- M-Audio Delta RBUS Инструкция по эксплуатации
- Polaris PCH 2073 Инструкция по эксплуатации
- Stiebel Eltron SHO AC 600 6/12 3352 Инструкция по эксплуатации
- Panasonic DMC-FS16EE-K Инструкция по эксплуатации