Braun Series 3 390cc [7/57] Before using clean renew
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Braun Series 3 390cc [7/57] Before using clean renew

Braun Series 3 390cc [7/57] Before using clean renew
8
small amount of oil, the cleaning procedure
also fulfills the lubrication needs of the shaver.
Important
• Only use the power supply cord set supplied
with the shaver.
• In order to avoid any leakage of the cleaning
fluid, place the appliance on a flat, stable
surface. Do not tip, move suddenly or
transport in any way if a cleaning cartridge
is installed.
• Do not place the appliance in a mirror cabi-
net, nor store it over radiators, nor place it
on polished or laquered surfaces. Do not
expose to direct sunlight.
• The appliance contains highly
flammable liquid. Keep it away from
sources of ignition. No smoking.
Keep out of reach of children. Do not refill
cartridge. Use only original Braun refill
cartridge.
• When cleaning the shaver, its protection
cap should be removed.
Description
1 Lift button for cartridge exchange
2 Contact bow
3 Start/release button
4 Level indicator
5 Cleaning cartridge
Before using Clean&Renew™
Installing the cartridge
• Press the lift button (1) to open the housing.
• Hold the cartridge down on a flat, stable
surface (e.g. table). Carefully remove the lid
from the cartridge. Slide the cartridge into
the base as far as it will go.
Slowly close the housing by pushing it down
until it locks.
Replacing the cartridge
After having pressed the lift button to open the
housing, wait for a few seconds before re-
moving the used cartridge.
Before discarding the used
cartridge, make
sure to close the openings using the lid of the
new cartridge, since the used cartridge will
contain contaminated cleaning solution.
The used cartridge can be disposed in the
household waste.
Operating your
Clean&Renew™
• Connect your Clean&Renew™ with the cord
set to the mains electricity supply. The
special socket at the back is adjustable to
save space. After each shave, switch the
shaver off and put it into the Clean&Renew™,
upside down and with the front showing.
• Push the start/release button (3) to lock and
connect the shaver. The cleaning process
will start. The yellow light on the shaver will
flash during the complete process (approx.
5 minutes cleaning, 4 hours drying).
• Do not interrupt the cleaning process, as it
leaves the shaver wet and not fit for use. If
interruption is needed nonetheless, press
the start/release button (3).
• When cleaning is finished, the yellow light
will go off and the shaver is ready for use.
To release it, push the start/release button.
• A cleaning cartridge should be sufficient
for about 30 cleaning cycles. When the level
indicator (4) has reached the «min» mark,
the remaining fluid in the cartridge is suf-
ficient for about 5 more cleaning cycles.
Then the cartridge should be replaced,
when used daily approx. every 4 weeks.
• The hygienic cleaning solution cartridge
contains alcohol which, once opened,
will naturally evaporate slowly into the
surrounding air. Each cartridge, if not used
daily should be replaced after approx.
8 weeks.
• Clean the housing from time to time with a
damp cloth, especially the opening where
the shaver rests.
Subject to change without notice.
5735322_390_AMEE Seite 8 Montag, 19. November 2007 11:59 11

Содержание

Похожие устройства

small amount of oil the cleaning procedure also fulfills the lubrication needs of the shaver Important Only use the power supply cord set supplied with the shaver In order to avoid any leakage of the cleaning fluid place the appliance on a flat stable surface Do not tip move suddenly or transport in any way if a cleaning cartridge is installed Do not place the appliance in a mirror cabi net nor store it over radiators nor place it on polished or laquered surfaces Do not expose to direct sunlight The appliance contains highly A flammable liquid Keep it away from sources of ignition No smoking Keep out of reach of children Do not refill cartridge Use only original Braun refill cartridge When cleaning the shaver its protection cap should be removed Description 1 Lift button for cartridge exchange 2 Contact bow 3 Start release button 4 Level indicator 5 Cleaning cartridge Before using Clean Renew Installing the cartridge Press the lift button 1 to open the housing Hold the cartridge down on a flat stable surface e g table Carefully remove the lid from the cartridge Slide the cartridge into the base as far as it will go Slowly close thehousing by pushing it down until it locks Replacing the cartridge After having pressed the lift button to open the housing wait for a few seconds before re moving the used cartridge 8 Before discarding the used cartridge make sure to close the openings using the lid of the new cartridge since the used cartridge will contain contaminated cleaning solution The used cartridge can be disposed in the household waste Operating your Clean Renew Connect your Clean Renew with the cord set to the mains electricity supply The special socket at the back is adjustable to save space After each shave switch the shaver off and put it into the Clean Renew upsidedown and with the front showing Push the start release button 3 to lock and connect the shaver The cleaning process will start The yellow light on the shaver will flash during the complete process approx 5 minutes cleaning 4 hours drying Do not interrupt the cleaning process as it leaves the shaver wet and not fit for use If interruption is needed nonetheless press the start release button 3 When cleaning is finished the yellow light will go off and the shaver is ready for use To release it push the start release button A cleaning cartridge should be sufficient for about 30 cleaning cycles When the level indicator 4 has reached the min mark the remaining fluid in the cartridge is suf ficient for about 5 more cleaning cycles Then the cartridge should be replaced when used daily approx every 4 weeks The hygienic cleaning solution cartridge contains alcohol which once opened will naturally evaporate slowly into the surrounding air Each cartridge if not used daily should be replaced after approx 8 weeks Clean the housing from time to time with a damp cloth especially the opening where the shaver rests Subject to change without notice

Скачать