Home
Главная
Timberk
Обогреватель
TEC.E1 M 1000
Инструкция по эксплуатации Страница: 4

Timberk TEC.E1 M 1000 Инструкция по эксплуатации онлайн [4/10] 11005

Содержание

Timberk 1
Модели models 1
Руководство по эксплуатации instruction manual 1
Convector description fig 3
Convector heater with a bracket 1 pc 2 special supports 2 pcs 3 wheels 4 pcs 4 clamps latches for wheel mounting 2 pcs 5 user manual 1 pc 6 guarantee slip 1 pc 3
Convector installation on the wall 3
Delivery set 3
Design and technical characteristics of the convector heater as well as its complete set may be changed by the manufacturer without prior notification when it is needed to improve its quality 3
Dimensional characteristics 3
Iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiim 3
Iiniiiiiiiiiiiiiii 3
Installation 3
Installation dimensions of the convector heater according to fig 2 are shown in table 3 table 3 3
Mounting of convector heater on legs 3
Open the original packing and take the appliance from there carefully 2 remove foam compactors from the appliance edges and clear it of polyethylene 3 in accordance with fig 2 4 and tables 2 3 specify a place for convector installation with observance of minimum distances from objects and minimum distance from the floor 4 mark an elevation for convector installation and then attach the bracket to the wall 5 make visible marks in mounting holes 6 drill the holes with required diameter in accordance with your marks insert dowels attach 3
Outletgrills 2 heated air outlet 3 cool air inlet 4 control panel 5 case front 6 wheels for mobile transportation 3
Overall dimensions of the convector heater according to fig 2 are shown in table 2 table 2 3
Take the legs from the convector heater box 2 standard set of legs number in one pack includes two special supports four wheels fixed by two on each support two latches to fix leg supports to the convector heater 3 insert the wheels into the support as shown in figure 6 remember that the wheels have a special pin screw for more convenient mounting of the wheels to the support 4 turn the appliance upside down remember that the convector heater should be mounted on the legs only when you unplug it 5 attach the legs to the bottom part of the appliance and make sure that mounting holes match with holes on the appliance case try to dispose legs in alignment with each other and to the convector surface 6 use special latches included in the set see clause 2 to fix the legs to the convector heater perhaps you will have to apply some physical effort to provide the reliable fixing 3
Technical characteristics 3
Technical characteristics of the convector heater are shown in table 1 table 1 3
The bracket and screw set screws fixing the bracket on the wall 7 place the convector heater on the bracket matching 4 slots on rear surface with 4 shoulders on the bracket fig 5 and pull down 8 to fix the convector turn the clamp on the top of the bracket clockwise and make sure that it enters the aperture in rear panel of the convector heater 3
To remove the convector heater repeat the above mentioned actions in reverse order 3
Iniiiiiiiiiiiiiiii 6
Iiiiiiiiiiiiiiiiiii 8
Iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiim 8
Iiiiiiiiiiiiiiiiiii 9
Timberk 9

Похожие устройства

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiim lllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllll lllllllllllllllll ENGLISH Convector heater operation 7 Check the reliability of fixing once again Turn the appliance to original position and place it upright on plane horizontal surface The appliance is ready for operation 1 Switching on 1 1 Connect the convector heater to power network by plugging it into the power outlet The indicator lamp POWER will flash 1 2 Press the switch key to switch the convector on 2 Selection of heating power mode except for 500W models Power network connection 1 The convector heater is intended for connection to power network with single phase voltage of 230 V 2 Before connection make sure that power network parameters in the point of connection correspond to parameters indicated on neck label with technical data for the appliance 3 While connecting the convector heater to the power network it is necessary to observe the working regulations for electrical safety 4 Convenience outlet should be earthed in the correct way The outlet should be designed for nominal current of not less than lOA Convenience outlet and a plug should always be dry in order to avoid current leakage Always check that the plug is tightly connected to the outlet The check should be performed in the following order insert the plug into the outlet After half hour of work shut off the convector heater and remove the plug from the outlet and check if the plug is hot If its temperature is more than 50 C replace it to avoid damages accidents or fires as a result of poor electric contact The plug should be replaced by a professional O Press the key 1 to select low heating power it will be indicated by a lamp of key 1 Press the key 2 to select average heating power it will be indicated by a lamp of key 2 Press the keys 1 and 2 to select high heating power it will be indicated by lamps of both keys 1 Thermostat knob Used to set a desired temperature in the room 2 Indicator lamp POWER Flashes when the appliance is connected to power network 3 Two key switch with indication Used to choose the following modes of heating power mode 1 low power mode 2 average power mode 3 high power 4 Plastic protection cap Except for model TEC E1 M 500 using a one key switch 3 Setting of temperature Open a transparent plastic protection cap on the control panel and provide the access to thermostat knob Turn the thermostat knob clockwise up to the stop At that if temperature in the room is lower than the set one the indicator lamp in the switch will flash When temperature in the room will reach the desired level turn the thermostat knob counterclockwise up to disconnection The indicator lamp in the switch will go out Then the thermostat will maintain the set temperature switching the convector on and off periodically In especially cold weather the convector may be unable to cope with heating of the room In such a case the thermostat knob should be set to the level which is a little higher than the desired one Control panel for series TEC E1 E Fig 8 9 WARNING The convenience outlet should be designed for nominal current of not less than 10A electrical cable with a core with section of not less than 3x1 5 mm2 for copper Fig 9 7 Convector heater control Convector heaters of series TEC E1 M are equipped with a mechanical thermostat Convector heaters of series TEC E1 E are equipped with a high precision electronic thermostat 1 Thermostat knob Used to set a desired temperature in the room 2 Indicator lamp POWER Flashes when the appliance is connected to power network 3 Two key switch with indication Used to choose thefollowing modes of heating power mode 1 low power mode 2 average power mode 3 high power 4 Plastic protection cap except for model TEC E1 E 500 using a one key switch 6 www timberk ru electric convector heater 4 Antifreeze mode r Turn the thermostat knob counterclockwise to the J position Thermostat will automatically switch on the convector heating if temperature in the room drops lower than 5 C so the appliance will be connected to the power network and the heating mode will be on 8 Service The appliance should be washed regularly to remove dust and dirt from external surfaces since it affects the efficiency of its work and temperature parameters of heating Before preventive maintenance shut off the appliance and unplug it let it cool down and then wipe its surface with a soft slightly wet cloth It is not recommended to wash it with detergents including agents with abrasive contents Exclude damaging of the appliance with sharp objects because scratches on its painted surface may result in emergence of rust Rear surface of the convector heater should also be cleaned of dust and dirt For that it is necessary to detach the appliance from the bracket and after cleaning return it to original position Preventive cleaning should be performed regularly to maintain good technical condition of the convector and keep its appearance for many years 9 Circuit schematics ModelTEC E1M500 Drop sensor Switch Thermostat L POWER indicator Heat indicator Heating element Heat suppressor N Fig 10 5 Switching off Set the key of the heating switch to the O position and unplug the appliance At that the indicator lamp POWER on the control panel will go out Comfort mode which can be selected with the use of the thermostat knob corresponds to the most comfortable temperature in the room www timberk ru electric convector heater

Скачать