Home
Главная
Scarlett
Машинка Для Стрижки Волос
SC-HC63C07
Инструкция по эксплуатации Страница: 4

Scarlett SC-HC63C07 [4/19] Important safeguards

IM013

www.scarlett.ru 4 SC-HC63C07

GB INSTRUCTION MANUAL

IMPORTANT SAFEGUARDS

• Please read this instruction manual carefully before

use and keep in a safe place for future reference.

• Before switching on the appliance for the first time

please check if the technical specifications

indicated on the unit correspond to the mains

parameters.

• For home use only. Do not use for industrial

purposes. Do not use the appliance for any other

purposes than described in this instruction manual.

• Do not use outdoors.

• Always unplug the appliance from the power supply

before cleaning and when not in use.

• To prevent risk of electric shock and fire, do not

immerse the appliance in water or any other

liquids. If it has happened DO NOT TOUCH the

appliance, unplug it immediately and check in a

service center.

• Do not take this product to a bathroom or use near

water.

• This appliance is not intended for use by persons

(including children) with reduced physical, sensory

or mental capabilities, or lack of experience and

knowledge, unless they have been given

supervision or instruction concerning use of the

appliances by a person responsible for their safety.

• Children should be supervised to ensure that they

do not play with the appliance.

• Do not leave the appliance switched on when not in

use.

• Do not use other attachments than those supplied.

• Do not operate after malfunction or cord damage.

• Do not attempt to repair, adjust or replace any

parts of the appliance. Check and repair the

malfunctioning appliance in the nearest service

center only.

• Keep the cord away from sharp edges and hot

surfaces.

• Do not place or store the appliance where it can fall

or be pulled into a tub or sink.

• Do not pull, twist, or wrap the power cord around

the appliance.

• Never insert any objects into openings in the

appliance housing.

• Do not put operating appliance on any surface, it

may cause injury or damage.

• Do not use the appliance with damaged comb, or

with teeth missing from the blades as injury may

occur.

• If the product has been exposed to temperatures

below 0ºC for some time it should be kept at room

temperature for at least 2 hours before turning it

on.

• NOTE: KEEP THE BLADES OILED.

• Do not use the hair clipper when the skin is

infected.

• Do not use the hair clipper on animals.

• The manufacturer reserves the right to introduce

minor changes into the product design without prior

notice, unless such changes influence significantly

the product safety, performance, and functions.

BLADE ALIGNMENT

• Your clipper was carefully examined to ensure that

the blades were oiled and properly aligned before

leaving our factory.

• Blades must be realigned if they were removed for

cleaning or after replacement.

• To realign the blades, simply match the upper and

lower blades teeth up, point for point.

• End of top blade teeth should be approximately 1.2

mm back from lower blade. Compare your clipper

blades with the sketch (pic.1).

• If blade alignment is incorrect, add a few drops of

oil to the blades, switch on the clipper for a few

moments, switch off and unplug. Loosen screws

slightly and adjust. Tighten screws after blade is

aligned.

OILING

• To maintain your clipper in peak condition, the

blades should be oiled after every haircut.

• Do not use hair oil, grease, oil mixed with kerosene

or any solvent.

BLADE LEVER

• The lever located to the left of the blades, allows

easily adjust cut hair length while clipping.

• The lever adds versatility to your clipper by

allowing you gradually change the closeness of

your cut without an attachment comb.

• When the lever is in the uppermost position, the

blades will give you the closest cut and leave the

hair very short. Pushing the lever downwards

gradually increases the cutting length.

• In its lowest position, the lever will leave the hair

approximately the same length as a №1 (3mm)

comb.

• The lever will also extend the use of your blades

since a different cutting edge is used in each

setting.

• In addition, if extremely heavy hair cutting has

jammed the blades, it will help you to remove hair

that has become wedged between the two blades

without removing the blades.

• While the clipper is running rapidly move the lever

from “close cut” to “longer cut” a couple of times.

Do this each time after you have finished using

your clipper to keep the blades free of cut hair.

• If this does not help and clipper stops cutting,

blades are dulled. Replace them with new blades.

INSTRUCTIONS FOR HAIR CUTTING

• Before starting the hair cut inspect the clipper,

making sure that there is no oil between the cutting

blade teeth, switch the unit on to distribute the oil

between the blade teeth and to check running

smoothness. Wipe off any excess oil. This should

be done after each use. While using the unit,

untwist the cord from time to time to avoid tangling.

• Before cutting always comb the hair thoroughly

first.

DETACHABLE COMBS

Attachment comb №

Hair length mm/inches

№1

3 (1/8)

№2

6 (1/4)

№3

9 (3/8)

№4

12 (1/2)

• Each comb attachment is marked accordingly on

its outside middle surface.

Scarlett SC-HC63C07 [4/19] Important safeguards

Содержание

Похожие устройства