![Aten VS0108 [21/33] Command for cascaded splitters](/img/pdf.png)
Aten VS0108 [21/33] Command for cascaded splitters
![Aten VS0102 [21/33] Command for cascaded splitters](/views2/1211546/page21/bg15.png)
Chapter 3. Operation
13
Command for Cascaded Splitters
Serial port commands for cascaded splitters require identifying the chain of
ports to which the target device is connected. The formula for Switch Port
commands are as follows:
Switch Command + Output Command + Port Number (at first stage) + Port
Number (at second stage) + Port Number (at third stage) + Control [Enter]
For the example above, the command for switching off the Target Output Port
4 of the splitter connected to Port 3 at the second stage of the cascade, which,
in turn, is connected to output Port 4 at the first stage unit, is as follows:
sw o04-03-04 off [Enter]
This cascade command format is applied to Mute Commands, page 15, Read
Commands, page 17, and Reset Commands,page 18. However, this is not
applicable to EDID commands, which apply only to the first stage unit splitter,
as well as the Firmware commands.
First Stage Unit
Second Stage Unit
Third Stage Unit
Target
Output
Содержание
- Vs0102 vs0104 vs0108 user manual p.1
- Vs0102 vs0104 vs0108 p.1
- Sj t 11364 2006 p.2
- Fcc information p.2
- User notice p.3
- User information p.3
- Telephone support p.3
- Online registration p.3
- Package contents p.4
- Operation p.5
- Introduction p.5
- Hardware setup p.5
- Contents p.5
- Appendix p.6
- About this manual p.7
- This manual uses the following conventions p.8
- Product information p.8
- For information about all aten products and how they can help you connect without limits visit aten on the web or contact an aten authorized reseller visit aten on the web for a list of locations and telephone numbers p.8
- Conventions p.8
- Overview p.9
- Introduction p.9
- Chapter 1 p.9
- Features p.10
- 1 vga audio cable for the source device you will be connecting p.11
- 1 vga audio cable for each display device you will be connecting p.11
- The following equipment must be installed on the source device or computer that acts as a source of vga audio content vga video card with hdb 15 connector p.11
- Supported operating systems are shown in the table below p.11
- Stereo and or balanced audio speakers p.11
- Source device p.11
- Requirements p.11
- Operating systems p.11
- Display device p.11
- Cables p.11
- Audio source with stereo output p.11
- A vga svga uxga wuxga or multisync monitor or multimedia projector with an hdb 15 connector p.11
- Vs0102 vs0104 vs0108 front view p.12
- Vs0102 rear view p.12
- Components p.12
- Vs0108 rear view p.13
- Vs0104 rear view p.13
- Chapter 2 p.14
- Rack mounting p.14
- Hardware setup p.14
- Grounding p.15
- Single stage p.16
- Installation p.16
- Installing the rs 232 controller p.17
- Cascade p.18
- Rs 232 serial interface p.19
- Overview p.19
- Operation p.19
- Configuring the serial port p.19
- Chapter 3 p.19
- Note 1 each command string can be separated with a space p.20
- If the port number string is skipped the default value is used p.20
- For example to turn on output port 02 type the following p.20
- For example to turn off output port 01 input the following p.20
- The formula for switch port commands are as follows p.20
- The following tables show the possible values and formats for the output command port number and control p.20
- The following table shows the available switch port command list p.20
- Switch port commands p.20
- Switch command output command port number control enter p.20
- Sw o02 on enter p.20
- Sw o01 off enter p.20
- Command for cascaded splitters p.21
- The formula for the edid mode selection commands are as follows p.22
- The following tables show the possible values and formats for the control command p.22
- The following table shows the available edid mode selection command list p.22
- For example to switch the edid setting to auto type the following p.22
- Extended display identification data edid is a data format that contains a display s basic information and is used to communicate with the video source system you can set up which edid mode the vs0102 vs0104 vs0108 uses with the commands that follow p.22
- Edid mode selection commands p.22
- Edid command control enter p.22
- Edid auto enter p.22
- To enable or disable audio coming from the output port use the following commands p.23
- The formula for the mute commands are as follows p.23
- The following tables show the possible values and formats for the output command port number and control command p.23
- The following table shows the available mute command list p.23
- Mute o04 on enter p.23
- Mute commands p.23
- Mute command output command port number control enter p.23
- For example to turn mute on for port 04 type the following p.23
- Upgrade enter p.24
- The formula for the firmware update command is as follows p.24
- The following tables show the possible values and formats for the command p.24
- The following table shows the available command list p.24
- The firmware update feature readies the vs0102 vs0104 vs0108 for a firmware upgrade p.24
- For example to start the firmware upgrade process input the following p.24
- Firmware update command p.24
- Command enter p.24
- The read command allows you to read information about the vs0102 vs0104 vs0108 p.25
- The formula for the read commands are as follows p.25
- The following tables show the possible values and formats for the output command port number and control command p.25
- Read version enter p.25
- Read o03 video enter p.25
- Read command output command port number control command enter p.25
- Read command p.25
- Note each command can be separated with a space p.25
- For example to display the video on off status for port 03 input the following p.25
- For example to display the firmware version for the device input the following p.25
- The following table shows the available read command list p.26
- The following table shows the available command list p.26
- Reset o02 enter p.26
- Reset device command p.26
- For example to reset port 02 back to the factory default settings input the following p.26
- Command enter p.26
- The reset feature resets the vs0102 vs0104 vs0108 back to the factory default settings the formula for the rest commands are as follows p.26
- The following tables show the possible values and formats for the output command and port number command p.26
- Verification p.27
- Powering off and restarting p.27
- Safety instructions p.28
- General p.28
- Appendix p.28
- Rack mounting p.30
- Technical support p.31
- North america p.31
- International p.31
- Vs0102 vs0104 vs0108 user manual p.32
- Specifications p.32
- Function vs0102 vs0104 vs0108 p.32
- The direct vendor also reserves the right to revise or update the device or documentation without obligation to notify any individual or entity of such revisions or update for further inquiries please contact your direct vendor p.33
- Limited warranty p.33
Похожие устройства
-
Aten VS132Краткое руководство по установке -
Aten VS132Описание и спецификации продукта -
Aten VS102Руководство пользователя -
Aten VS98AКраткое руководство по установке -
Aten VS98AОписание и спецификации продукта -
Aten VS94AКраткое руководство по установке
-
Aten VS94AОписание и спецификации продукта
-
Aten VS92AОписание и спецификации продукта
-
Aten VS92AКраткое руководство по установке
-
Aten VS88Руководство пользователя -
Aten VS88Описание и спецификации продукта -
Aten VS84Руководство пользователя