Fubag F1-241/50 CM2 [9/16] Maintenance

Содержание

• Operator s manual 1
• Инструкция по эксплуатации 1
• Operator s manual 2
• Page01 2
• Page02 3
• Page03 4
• Page04 5
• Operator s manual 6
• Page05 6
• Safety operation 6
• Caution 7
• Not to do 7
• Operator s manual 7
• Page06 7
• Operator s manual 8
• Page07 8
• Start up and use 8
• Technical specifications 8
• Maintenance 9
• Operator s manual 9
• Page08 9
• Operator s manual 10
• Page09 10
• Troubleshooting 10
• Warranty 10
• Page10 11
• Инструкция по эксплуатации 11
• Ипад 11
• Правила безопасности 11
• Page11 12
• Важно 12
• Гипад 12
• Запрещается 12
• Инструкция по эксплуатации 12
• Page12 13
• Инструкция по эксплуатации 13
• Пуск и эксплуатация 13
• Технические характеристики 13
• Шрад 13
• Page13 14
• Инструкция по эксплуатации 14
• Техническое обслуживание 14
• Page14 15
• Гарантийные обязательства 15
• Гиьад 15
• Инструкция по эксплуатации 15
• Неисправности и способы их устранения 15
• Cover 2 16

Похожие устройства

• Fubag F1-241/24 CM2 Инструкция по эксплуатации
• Fubag IR 180 Инструкция по эксплуатации
• Fubag IR 200 VRD Инструкция по эксплуатации
• Fubag IR 220 VRD Инструкция по эксплуатации
• Fubag IN 163 Инструкция по эксплуатации
• Fubag IN 203 Инструкция по эксплуатации
• Fubag IRMIG 160 Инструкция по эксплуатации
• Fubag IRMIG 180 Инструкция по эксплуатации
• Fubag IRMIG 140 Инструкция по эксплуатации
• Fubag IRMIG 200 Инструкция по эксплуатации
• Fubag INMIG 250 T Инструкция по эксплуатации
• Fubag INMIG 315 T Инструкция по эксплуатации
• Asus x556ub, 90nb09r1-m02890 Инструкция по эксплуатации
• Asus x556ub, 90nb09r1-m02900 Инструкция по эксплуатации
• Asus x555sj, 90nb0ak8-m01470 Инструкция по эксплуатации
• Asus x540sa, 90nb0b31-m06340 Инструкция по эксплуатации
• Asus k501uq, 90nb0bp2-m00470 Инструкция по эксплуатации
• Asus gl702vt, 90nb0cq1-m01300 Инструкция по эксплуатации
• Asus gl502vs, 90nb0dd1-m00990 Инструкция по эксплуатации
• Asus g752vm, 90nb0d61-m00430 Инструкция по эксплуатации

Fubag Operator s manual www fubag ru The compressor continues to operate automatically with this work cycle until the position of the switch of the pressure switchis modified To use the compressor again wait at least 10 seconds after this has been switched off before restarting Air pressure can be regulated in order to optimize use of air powered tools operating on the knob with the valve open pulling it up and turning it in a clockwise direction to increase pressure and counterclockwise to reduce this fig 9a 9b 9c 9d Once you have set the value required push the knob down to lock it Please check that the air consumption and the maximum working pressure of the pneumatic tool to be used are compatible with the pressure set on the pressure regulator and with the amount of air supplied by the compressor When you have finished working stop the machine pull out the plug and empty the reservoir fig 10 11 4 Maintenance The service life of the machine depends on maintenance quality BEFORE CARRYING OUTANY OPERATION ALWAYS PULL OUT THE PLUG AND DRAIN THE RECEIVER COMPLETELY fig 10 11 Tighten the tie bolts of the head at start up and after the first hour of work torque 10 Nm 1 02 Kgm After loosening any safety screws fig 12a clean the intake filter according to the type of working environment and at least every 100 hours fig 12b 12c If necessary replace the filter element clogging of the filter reduces compressor performance and an inefficient filter causes increased wear Replace the oil after the first 100 hours of operation and every 300 hours subsequently fig 13a13b 13c Remember to check the oil level at regular intervals Periodically or after working with the compressor for more than an hour drain the condensate that forms inside the receiver fig 11 due to the humidity in the air This protects the receiver from corrosion and does not restrict its capacity TABLE 1 MAINTENANCE FUNCTION AFTER THE FIRST 100 HOURS Cleaning of intake filter and or substitution of filtering element Change of oil EVERY 100 HOURS EVERY 300 HOURS Tightening of head tension rods The check must be carried out prior to the first compressor starting Draining tank condensate Periodically and at the end of work Spent oil and condensate must be disposed of in compliance with protection of the environment and current legislation