Home
Главная
Saturn
Утюг
ST-CC7108
Руководство пользователя Страница: 3

Saturn ST-CC7108 Руководство пользователя онлайн [3/18] 178590

DESCRIPTION OF DEVICE

1. Sole plate

2. Spray organ

3. Filler door

4. Steam dial

5. Spray button

6. Shot steam button

7. Top cover

8. Water tank

9. Power supply cord

10. Protect wire cover

11. Body of iron

12. Back cover

13. Heat isolating

14. Temperature control knob

15. Water Cup

ANTI-CALC SYSTEM

A special resin filter inside the water

reservoir softens the water and

prevents scale build-up in the plate.

The resin filter is permanent and does

not need replacing.

ANTI-DRIP SYSTEM

With the anti-drip system, you can

perfectly iron even the most delicate

fabrics.

Always iron these fabrics at low

temperatures. The plate may cool

down to the point where no more

steam comes out, but rather drops of

boiling water that can leave marks or

stains. In these cases, the Anti-drip

system automatically activates to

prevent vaporization, so that you can

iron the most delicate fabrics without

risk of spoiling or staining them.

GENERAL INSTRUCTIONS

When using the iron for the first time,

you may notice a slight emission of

smoke and hear some sounds made

by the expanding plastics. This is quite

normal and it stops after a short time.

We also recommend passing the iron

over an ordinary cloth before using it

for the first time.

PREPARATIONS

Soft the laundry to be ironed

according to the international symbols

on the garment label, or if this is

missing, according to the type of

fabric.

GARMENT

LABEL

FABRIC

TYPE

THERMO-

STAT

REGULA-

TION

synthetic

low

temperat

ure

silk -

wool

··

medium

temperat

ure

cotton -

linen

···

high

temperat

ure

Fabric not to be

ironed

Start ironing the garments requiring a

low temperature.

This reduces the waiting times (the

iron takes less time to heat up than to

cool down) and eliminates the risk of

scorching the fabric.

STEAM IRONING

Filling the reservoir

- Check that the plug is disconnected

from the socket.

- Move the steam selector (4) to “0”

[Fig. 1].

- Open the lid (2).

- Raise the tip of the iron to help the

water enter the opening without

overflowing.

- Slowly pour the water into the

reservoir using the special measure

and taking care not to go over the

maximum level (about 180ml)

indicated by “MAX” on the reservoir

[Fig. 2].

- Close the lid (2).

SELECTING THE TEMPERATURE

- Put the iron in a vertical position.

- Put the plug in the socket.

- Adjust the thermostat knob (14)

according to the international symbol

on the garment label [Fig. 3]. The

plate temperature control light

indicates that the iron is heating up.

Wait until the plate temperature

control light goes off before ironing.

Warning: during ironing, the plate

temperature control light comes on at

intervals, indicating that the selected

temperature is maintained. If you

lower the thermostat temperature

after ironing at a high temperature, do

not start ironing until the plate

temperature control light comes on

again.

SELECTING THE STEAM.

The quantity of steam is regulated by

the steam selector (4).

- Move the steam selector to a

position between minimum and

maximum depending on the quantity

of steam required and the

temperature selected [Fig. 1].

Warning: the iron gives off steam

continuously only if you hold the iron

horizontally. You can stop the

continuous steam by placing the iron

in a vertical position or by moving the

steam selector to “0”. As indicated on

the thermostat knob (14) and in the

initial table, you can only use steam at

the highest temperatures. If the

selected temperature is too low, water

may drip onto the plate.

SELECTING SHOT-STEAM AND

STEAM WHEN IRONING

VERTICALLY

Press the shot-steam button (6) to

generate a powerful burst of steam

that can penetrate the fabrics and

smooth the most difficult and tough

creases. Wait for a few seconds before

pressing again [Fig. 4].

By pressing the shot-steam button at

intervals you can also iron vertically

(curtains, hung garments, etc.) [Fig.

5].

Warning: the shot-steam function

can only be used at high

temperatures. Stop the emission when

the plate temperature control light

comes on, than start ironing again

only after the light has gone off.

DRY IRONING

To iron without steam, follow the

instructions in section “steam ironing”,

leaving the steam selector (4) on

position “0”.

Spray Function

Make sure that there is water in the

reservoir. Press the spray button (5)

slowly (for a dense spray) or quickly

(for a vaporized spray) [Fig. 6].

Warning: for delicate fabrics, we

recommend moistening the fabric

beforehand using the spray function

(5), or putting a damp cloth between

the iron and the fabric. To avoid

staining, do not use the spray on silk

or synthetic fabrics.

CLEANING

Please note: before cleaning the iron

in any way, make sure that the

appliance plug is not connected to the

socket.

Any deposits, starch residue or size

left on the plate can be removed using

a damp cloth or an unabrasive liquid

detergent.

Avoid scratching the plate with steel

wool or metallic objects.

The plastic parts can be cleaned with a

damp cloth then wiped over with a dry

cloth.

HOW TO PUT IT AWAY

- Disconnect the plug of the iron from

the socket.

- Empty the reservoir by turning the

iron upside down and gently shaking

it.

- Leave the iron to cool down

completely.

- Roll up the power cord with the

rewinder [Fig. 8].

- Always put the iron away in a

vertical position.

Saturn ST-CC7108 Руководство пользователя онлайн [3/18] 178590

Содержание

Похожие устройства