Главная
Skipped breadcrumb items
abs-10,8 li-2 bmc
Инструкция по эксплуатации Страница: 16

Главная
DWT
abs-10,8 li-2 bmc
Инструкция по эксплуатации Страница: 16

DWT abs-10,8 li-2 bmc — инструкция по зарядке и замене аккумулятора инструмента [16/136]

Превью страниц Страница 16 / 136

• Mount / replace the accessory. • Fig. 10.4 - (the green indicator 16 is blinking, the

• Tighten the keyless chuck 1 without skewing the

battery 9 is inserted in the charger 11) - the charging

process of the battery 9 is terminated due to

accessory as it is shown in figures 1-2.

inappropriate temperature. When the temperature

conditions are normal, the process of charging will

Mounting / dismounting of the keyless chuck (see

resume.

fig. 3-6)

• Fig. 10.5 - (the red indicator 15 is blinking, the battery 9

is inserted in the charger 11) - the charging process of

• To mount the keyless chuck 1, carry out the

the battery 9 is terminated because of its failure.

operations in consecutive stages as it is shown in

Replace the faulty battery 9, its further use is prohibited.

figures 3-5.

• To dismount the keyless chuck 1, carry out the

In the process of charging the battery 9

operations in consecutive stages as it is shown in

and the charger 11 become hot, it is a

figures 4-6.

normal process.

Attention: keep in mind that in the

Switching the power

tool on / off

process of mounting / dismounting of the

keyless chuck 1 the screw 12 has a left-

Make sure that the reverse switch 7 is not centred;

hand thread.

this blocks on / off switch 6.

Screwdriver bit / magnetic holder (see fig. 7)

Switching on:

Press on / off switch 6.

For short screwdriver bits use the magnetic

Switching off:

holder 13 for their reliable fixing (see fig. 7).

Release the on / off switch 6.

A magnetic holder 13 is not needed for extended

screwdriver bits 2 (specially purposed for

Design features

screwdrivers).

of the power tool

Charging procedure

Battery (see fig. 11)

of the power tool battery

• Li-Ion battery 9 can be put on and remove from

Initial operation of the power tools

charger 11 at any time (regardless of the charging state) -

it does not affect its service life and it does not lead to

The power tool is supplied with a partially charged

the loss of its capacity.

battery 9. Before the first use, the battery 9 must be

• The battery 9 is protected by the safety system

fully charged.

against deep discharge. In case of complete discharge,

the power tool is automatically switched off. Attention:

The battery 9 must be charged in the

do not try to switch on the power tool when the

appropriate temperature (from 0°C to

protection system is activated the battery 9 can be

45°C).

damaged.

Charging process (see fig. 8-9)

[ABS-14,4 SLi, ABS-18 SLi, ABS-14,4 TLi, ABS-18 TLi]

• Centre the reverse switch 7.

With the push of the button 18 the indicators 17 show

• Connect the charger 11 to the power supply.

the state of charge of the battery 9 (see fig. 11).

• Press the battery lock 10 (ABS-10,8 Li - two battery

locks 10), remove the battery 9 and insert it in the

Temperature protection

charger 11 (see fig. 8-9).

The temperature protection system enables to

• When battery is fully charged, disconnect the battery 9

from the charger 11 and mount it in the power tool.

automatically deactivate the power tool in case of

excess load or when the temperature of the battery 9 is

• Switch off the charger 11 after use.

exceeding 70°C. The system guarantees protection of

the power tool from damage in case of noncompliance

Charger indicators (see fig. 10)

with the operation conditions.

Charger indicators 15 and 16 inform of the battery 9

LED lamp

charging process. Signals of the indicators 15 and 16

are shown on the label 14 (see fig. 10.1-10.5).

When the on / off switch 6 is pushed, the LED lamp 3 is

• Fig. 10.1 - (the green indicator 16 is on, the battery 9 is

automatically switched on that allows to carry out works

not inserted in the charger 11) - the charger 11 is

in low light conditions.

connected to the power network.

• Fig. 10.2 - (the red indicator 15 is on, the battery 9 is

Torque regulator

inserted in the charger 11) - the battery 9 is being charged.

• Fig. 10.3 - (the green indicator 16 is on, the battery 9 is

Rotate the regulator 4 in order to set one of the 18

inserted in the charger 11) - the battery 9 is fully charged.

torque values most suitable for the work performed.

English

DWT abs-10,8 li-2 bmc — инструкция по зарядке и замене аккумулятора инструмента [16/136]

Содержание

Похожие устройства