Shop-Vac blower vac 25 [3/9] Assembly
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Shop-Vac blower vac 25 [3/9] Assembly

Shop-Vac blower vac 25 [3/9] Assembly
ASSEMBLY
TOP HANDLE ASSEMBLY
(Not standard with all models)
To attach top handle, align holes in handle and holes in tank cover and secure
with screws provided (Figure 1).
TOOL HOLDER ASSEMBLY
(Not standard with all models)
1. With rear of unit facing you, take tool holder and position it with tabs facing rear
of unit (Figure 2).
2. Place “J” shaped tabs into the slots on cord wraps (Figure3).
3. Press down until tabs snap into place.
4. Press down on center of tool holder until tab latches on bottom of lid (Figure 4).
1RW DOO XQLWV DUH HTXLSSHG ZLWK WKH VDPH FDVWHU V\VWHP )ROORZ WKH
LQVWUXFWLRQVZKLFKDSSO\WR\RXUVSHFLILFXQLW
Without Caster Feet
You will find four casters (Figure 5) with your wet/dry vacuum. Assemble as follows:
1. With cord disconnected from receptacle and tank cover removed, turn tank upside down so
that bottom is facing up.
2. Insert casters into bottom of tank by placing stem of caster
into holes provided. Apply pressure and twisting motion
until casters snap into place (Figure 6).
3. Return tank to upright position.
CASTER SYSTEM ASSEMBLY
B
A
A
A
A
A
A
B
B
B
B
B
B
A
A
16
23
22
21
20
17
18
19
10 U.S. Gallons (37.8L) and Up With Caster Feet
You will find four caster feet, four casters and four screws (Figure 16) with your wet/dry vacuum.
Assemble as follows:
1. With cord disconnected from receptacle and tank cover removed, turn tank upside down so
that bottom is facing up.
2. With front of tank facing you, take caster feet marked with the letter A (Figure 17) and place
in slots on left front and right rear of tank also marked with the letter A (Figure 18). Secure
with screws provided (Figure 19).
3. Take caster feet marked with the letter B (Figure 20) and place in slots on right front and left
rear of tank also marked with the letter B (Figure 21). Secure with screws provided (Figure
22).
4. If flat washers are included in hardware package place flat washer over stem of caster before
installing casters into feet. NOTE: Flat washers are not required with all units.
5-8 U.S. Gallons (18.9 - 30.2L) With Caster Feet
You will find four caster feet (Figure 7), four casters (Figure 8), and four screws with your wet/
dry vacuum. Assemble as follows:
1. With cord disconnected from receptacle and tank cover removed, turn tank
upside down so that bottom is facing up.
2. Remove any webbing that attaches the caster feet to each other.
3. With front of tank inlet facing you, take caster feet marked with the letter A
(Figure 9) and insert stem of caster foot into holes on left front and right rear
of tank also marked with letter A (Figure 10). Make sure caster feet are fully
inserted into tank bottom and secure with screws provided (Figure 11).
4. Take caster feet marked with the letter B (Figure 12) and insert stem of
caster foot into holes on right front and left rear of tank also marked with
the letter B (Figure 13). Make sure caster feet are fully inserted into tank
bottom and secure with screws provided (Figure 14).
5. Insert casters into feet by placing stem of caster into holes provided. Apply pressure and
twisting motion until casters snap into place (Figure 15).
6. Return tank to upright position.
11
B
B
12
B
B
B
B
A
A
13
14
15
A
A
A
A
10
A
A
9
With Rear Caster Dolly/Tool Holder
You will find four casters (Figure 24), two caster feet (Figure 25), rear caster dolly/tool holder
(Figure 26), and four screws with your wet/dry vacuum. Assemble as follows:
1. With cord disconnected from receptacle and tank cover removed, turn tank upside down so
that the bottom is facing up.
2. Take rear caster dolly and place into slots (on rear of tank, opposite of drain) and secure with
screws provided (Figure 27).
3. If flat washers are included in hardware package place flat washer over stem of caster before
installing casters into feet. NOTE : Flat washers are not required with all units.
4. Insert casters into bottom of rear caster dolly by placing stem of caster into holes provided.
Apply pressure and twisting motion until casters snap into place (Figure 28).
5. With tank drain facing you, take caster foot marked with the letter A (Figure 29) and place
in slot on left side of tank also marked with the letter A. Secure with screw provided (Figure
30).
6. Take caster foot marked with the letter B (Figure 31) and place in slot on right side of tank
also marked with the letter B. Secure with screw provided (Figure 32).
7. Insert casters into feet by placing stem of casters into holes provided. Apply pressure and
twisting motion until casters snap into place (Figure 33).
8. Return tank to upright position.
9. Place tool basket (not standard with all models) with curved surface against tank on rear
caster dolly assembly (Figure 34).
24
25
26
A
B
A
A
B
A
B
27
34
33
32
31
28
29
30
5. Insert casters into feet by placing stem of caster into holes provided. Apply pressure and
twisting motion until casters snap into place (Figure 23). Return tank to upright position.
REAR CASTER ACCESSORY CADDY AND
FRONT CASTER FEET ASSEMBLY
(Not standard with all models)
You will find four casters, two caster feet, an accessory caddy and four screws
with your wet/dry vacuum.
If your accessory caddy looks like the one pictured in (Figure 35) assemble as
follows.
1. With cord disconnected from receptacle and tank cover removed, turn tank
upside down so that the bottom is facing up.
2. Insert two caster feet into adjacent slots at front of tank. Secure with screws
provided.
3. Take accessory caddy and place into remaining slots at back of tank. Secure
with screws provided (Figure 36).
4. Install casters into caddy and feet by inserting the caster stems into the holes
provided. Apply pressure and twisting motion until casters snap into place.
1
2
3
4
6
5
7
8
35
36
If your accessory caddy looks like the one pictured in (Figure 37) assembly as follows.
1. With cord disconnected from receptacle and tank cover removed, turn tank upside down so
that the bottom is facing up.
2. Take accessory caddy and place into slots (on rear of tank opposite of drain). Secure with
screws provided (Figure 38).
3. With tank drain facing you, take caster foot marked with the letter A (Figure 39) and place
in slot on left side of tank also marked with the letter A. Secure with screw provided (Figure
40).
4. Take caster foot marked with the letter B (Figure 41) and place in slot on right side of tank
also marked with the letter B. Secure with screw provided (Figure 42).

Содержание

Похожие устройства

Скачать