Vitek VT-2567 GR [6/36] English
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Vitek VT-2567 GR [6/36] English

Vitek VT-2567 GR [6/36] English
6
ENGLISH
6
Using the power adapter
The unit connected to the mains is always
ready to use.
If you want to continue using the unit at
partially discharged battery, connect the
plug of the power adapter (12) cord to
the socket (1) on the lower part of the unit
body, connect the power adapter (12)
into the mains socket, switch on the unit
setting the power switch (3) to the “I” posi-
tion, the on indicator (2) will light up red.
Lubricating the blade block
Before using the unit for the first time
remove the blade block (5) and lubricate it
with oil (10) (supplied with the unit).
– To remove the blade block place the
clipper with the blades up and press on
the upper edge of the blade block with
your thumb to release it from the lock-
ing frame, as shown on pic. 1.
– Points for applying the lubricating oil
are marked with arrows on the pic. 2.
Apply 1 drop of oil to each point.
– To install the blade block back to its
place first insert its lower part to the
installation place and then carefully
press on the upper edge of the blades
until clicking to lock it, see the pic. 3.
– Let the hair clipper operate for approxi-
mately 30 seconds to spread the oil
across the rubbing surfaces. After that
remove the surplus oil with a dry cloth
or a paper towel.
Notes:
– Always set the blade height switch (6)
to the lower position to avoid difficulties
when installing the blade block to its place.
– Lubricate the blades after every use of
the hair clipper.
– Use only the oil (10) supplied with the set.
– Do not use vegetable oil or oil that
includes solvents. Solvents will evapo-
rate, leaving thick grease that may slow
down the blades motion.
Blade height switch 0.8/1.8 mm (6)
When the switch is in the lower (usual)
position (see pic. 4), the cutting length
is 1.8 mm. To reduce the cutting length
to 0.8 mm set the switch (6) to the upper
position (see pic. 5).
Universal attachments (8) and (9)
Each universal attachment (8) and (9) has
6 positions for hair of different length. It is
indicated on the scale situated on the left
side of the hair clipper body:
– universal attachment (8) for 3 mm,
6 mm, 9 mm, 12 mm, 15 mm, 18 mm
hair length;
– universal attachment (9) for 21 mm,
24 mm, 27 mm, 30 mm, 33 mm, 36 mm
hair length (see pic. 6).
– Before installing, removing or changing
the universal attachments, switch the
unit off by setting the power switch (3)
to the position «O»; if the unit is pow-
ered by the power adapter, unplug it.
– To install the universal attachment
insert its guides into the corresponding
grooves on both sides of the hair clip-
per body and move the attachment until
bumping to lock it.
– To adjust the cutting length turn the
adjuster (7) counterclockwise with your
thumb (see pic. 7) to set the required
cutting length according to the scale
(see pic. 6).
Attention: Do not try to adjust the
cutting length with the adjuster (7)
during the unit operation, because
when the power switch is set to the
position «I», the adjuster (7) is blocked.
It may damage the adjuster rack
mechanism.
Hair thinning function
The unit has the hair thinning function which
allows to visually improve the hairstyle by
thinning out hair. Hair thinning makes the
IM VT-2567.indd 6 08.07.2016 17:08:43

Содержание

Похожие устройства

Скачать
Случайные обсуждения

Ответы 1

Стояла на зарядке более 12 часов, индикатор так и остался красный. Неужели аккумулятор?
6 лет назад