![Gigabyte GA-Z270N-WIFI — настройки питания и включения системы после отключения электроэнергии [35/48]](/icons/site-icon-64.png){kind=icon}
Gigabyte GA-Z270N-WIFI — настройки питания и включения системы после отключения электроэнергии [35/48]
Превью страниц
Страница 35 /
48
![Gigabyte GA-H270N-WIFI [35/48] Soft off by pwr bttn](/views2/1232908/page35/bg23.png)
& AC BACK
Determines the state of the system after the return of power from an AC power loss.
Always Off The system stays off upon the return of the AC power. (Default)
Always On The system is turned on upon the return of the AC power.
Memory The system returns to its last known awake state upon the return of the AC power.
& Power On By Keyboard
Allows the system to be turned on by a PS/2 keyboard wake-up event.
Note: To use this function, you need an ATX power supply providing at least 1A on the +5VSB lead.
Disabled Disables this function. (Default)
Any Key Press any key to turn on the system.
Keyboard 98 Press POWER button on the Windows 98 keyboard to turn on the system.
Password Set a password with 1~5 characters to turn on the system.
& Power On Password
Set the password when Power On By Keyboard is set to Password.
Press <Enter> on this item and set a password with up to 5 characters and then press <Enter> to accept.
To turn on the system, enter the password and press <Enter>.
Note: To cancel the password, press <Enter> on this item. When prompted for the password, press <Enter>
again without entering the password to clear the password settings.
& Power On By Mouse
Allows the system to be turned on by a PS/2 mouse wake-up event.
Note: To use this function, you need an ATX power supply providing at least 1A on the +5VSB lead.
Disabled Disables this function. (Default)
Move Move the mouse to turn on the system.
Double Click Double click on left button on the mouse to turn on the system.
& ErP
Determines whether to let the system consume least power in S5 (shutdown) state. (Default: Disabled)
Note: When this item is set to Enabled, the following functions will become unavailable: Resume by Alarm,
PME event wake up, power on by mouse, power on by keyboard, and wake on LAN.
& Soft-Off by PWR-BTTN
Congures the way to turn off the computer in MS-DOS mode using the power button.
Instant-Off Press the power button and then the system will be turned off instantly. (Default)
Delay 4 Sec. Press and hold the power button for 4 seconds to turn off the system. If the power
button is pressed for less than 4 seconds, the system will enter suspend mode.
& Power Loading
Enables or disables dummy load. When the power supply is at low load, a self-protection will activate causing
it to shutdown or fail. If this occurs, please set to Enabled. Auto lets the BIOS automatically congure this
setting. (Default: Auto)
& Resume by Alarm
Determines whether to power on the system at a desired time. (Default: Disabled)
If enabled, set the date and time as following:
Wake up day: Turn on the system at a specic time on each day or on a specic day in a month.
Wake up hour/minute/second: Set the time at which the system will be powered on automatically.
Note: When using this function, avoid inadequate shutdown from the operating system or removal of the
AC power, or the settings may not be effective.
& RC6(Render Standby)
Allows you to determine whether to let the onboard graphics enter standby mode to decrease power
consumption. (Default: Enabled)
- 35 -
Содержание
272- User s manual
- Rev 1002 12me z270nwf 1002r
- Ga z270n wifi ga h270n wifi
- Motherboard
- Wireless module country approvals
- See the latest safety and regulatory documents at gigabyte s website
- Ga z270n wifi ga h270n wifi
- Dec 9 2016
- Identifying your motherboard revision
- Disclaimer
- Copyright
- Chapter 2 bios setup 0
- Chapter 1 hardware installation
- Table of contents
- Ga z270n wifi ga h270n wifi motherboard layout
- Chapter 3 appendix 7
- Two sata cables
- Quick installation guide
- One antenna
- Note the connector chip is on the back of the motherboard
- N n only for ga h270n wifi
- Motherboard driver disk 5 wireless module driver disk
- M only for ga z270n wifi
- I o shield
- Ga z270n wifi or ga h270n wifi motherboard
- Ga z270n wifi ga h270n wifi motherboard layout
- Ga z270n wifi
- Ga h270n wifi
- Box contents
- User s manual
- Chapter 1 hardware installation
- 1 installation precautions
- 2 productspecifications
- 2 product specifications
- Installing the cpu
- Dualchannelmemoryconfiguration
- 4 installing the memory
- 3 installing the cpu
- Sma antenna connectors 2t2r
- Rj 45 lan port
- Ps 2 keyboard mouse port
- Hdmi port
- Dvi d port
- 6 back panel connectors
- 5 installing an expansion card
- Usb 3 gen 1 port
- Usb type
- Rear speaker out black
- Optical s pdif out connector
- Mic in pink
- Line out green
- Line in blue
- Center subwoofer speaker out orange
- 7 internal connectors
- 2 atx_12v atx 2x2 12v power connector and 2x12 main power connector
- These fan headers are not configuration jumper blocks do not place a jumper cap on the headers
- The 12v power connector mainly supplies power to the cpu if the 12v power connector is not connected the 12v power connector mainly supplies power to the cpu if the 12v power connector is not connected the computer will not start
- Overheating overheating may result in damage to the cpu or the system may hang
- Be sure to connect fan cables to the fan headers to prevent your cpu and system from
- All fan headers on this motherboard are 4 pin most fan headers possess a foolproof insertion design when connecting a fan cable be sure to connect it in the correct orientation the black connector wire is the ground wire the motherboard supports cpu fan speed control which requires the use of a cpu fan with fan speed control design for optimum heat dissipation it is recommended that a system fan be installed inside the chassis
- 4 cpu_fan sys_fan fan headers
- With the use of the power connector the power supply can supply enough stable power to all the components on the motherboard before connecting the power connector first make sure the power supply is turned off and all devices are properly installed the power connector possesses a foolproof design connect the power supply cable to the power connector in the correct orientation
- Sata3 0 1 2 3 4 5 sata 6gb s connectors
- Bat battery
- The m connector on the back of the motherboard supports m sata ssds and m pcie ssds and support raid configuration through the inte
- Select the proper hole for the m ssd to be installed and refasten the screw and nut
- M m socket 3 connector
- Installation notices for the m and sata connectors
- Follow the steps below to correctly install an m ssd in the m connector step 1 use a screw driver to unfasten the screw and nut from the motherboard locate the proper mounting hole for the m ssd to be installed and then screw the nut first step 2 slide the m ssd into the connector at an angle step 3 press the m ssd down and then secure it with the screw
- Due to the limited number of lanes provided by the chipset the availability of the sata connectors may be affected by the type of device installed in the m connector the m connector shares bandwidth with the sata3 0 connector refer to the following table for details
- Chipset please note that an m pcie ssd cannot be used to create a raid set either with an m sata ssd or a sata hard drive and can only be used to build a raid set with uefi refer to chapter 3 configuring a raid set for instructions on configuring a raid array
- Nc purple no connection
- Hd hard drive activity led blue connects to the hard drive activity led on the chassis front panel the led is on when the hard drive is reading or writing data
- F_panel front panel header
- F_audio front panel audio header
- Connects to the power status indicator on the chassis front panel the led is on when the system is operating the led is off when the system is in s3 s4 sleep state or powered off s5
- Connect the power switch reset switch and system status indicator on the chassis to this header according to the pin assignments below note the positive and negative pins before connecting the cables
- The front panel audio header supports intel high definition audio hd and ac 97 audio you may connect your chassis front panel audio module to this header make sure the wire assignments of the module connector match the pin assignments of the motherboard header incorrect connection between the module connector and the motherboard header will make the device unable to work or even damage it
- Res reset switch green connects to the reset switch on the chassis front panel press the reset switch to restart the computer if the computer freezes and fails to perform a normal restart
- Pw power switch red connects to the power switch on the chassis front panel you may configure the way to turn off your system using the power switch refer to chapter 2 bios setup power for more information
- Pled power led yellow
- This header supports digital s pdif out and connects a s pdif digital audio cable provided by expansion cards for digital audio output from your motherboard to certain expansion cards like graphics cards and sound cards for example some graphics cards may require you to use a s pdif digital audio cable for digital audio output from your motherboard to your graphics card if you wish to connect an hdmi display to the graphics card and have digital audio output from the hdmi display at the same time for information about connecting the s pdif digital audio cable carefully read the manual for your expansion card
- The header conforms to usb 3 gen 1 usb 2 specification and can provide two usb ports for purchasing the optional 3 front panel that provides two usb 3 gen 1 ports please contact the local dealer
- Speaker speaker header
- Spdif_o s pdif out header
- F_usb30 usb 3 gen 1 header
- Connects to the speaker on the chassis front panel the system reports system startup status by issuing a beep code one single short beep will be heard if no problem is detected at system startup
- Use this jumper to clear the bios configuration and reset the cmos values to factory defaults to clear the cmos values use a metal object like a screwdriver to touch the two pins for a few seconds
- This motherboard provides a chassis detection feature that detects if the chassis cover has been removed this function requires a chassis with chassis intrusion detection design
- The header conforms to usb 2 1 specification each usb header can provide two usb ports via an optional usb bracket for purchasing the optional usb bracket please contact the local dealer
- F_usb1 usb 2 1 header
- Clr_cmos clear cmos jumper
- Ci chassis intrusion header
- Chapter 2 bios setup
- 1 startup screen
- Host clock value
- Graphics unslice rati
- Graphics slice rati
- Fclk frequency for early power o
- Cpu upgrad
- Cpu frequency
- Cpu clock ratio
- Cpu base clock
- Advanced frequency settings
- 2 m i t
- Cpu clock ratio cpu frequency fclk frequency for early power o
- Core current limit amps
- Avx offset
- Advanced cpu core settings
- Uncore ratio
- Uncore frequency
- Turbo rati
- Speed shift technology
- Power limit tdp watts power limit time
- No of cpu cores enabled
- Intel r turbo boost technology
- Intel r speed shift technology inte
- Hyper threading technology
- Cpu flex ratio settings
- Cpu flex ratio override
- Cpu enhanced halt c1e
- C6 c7 state support
- C3 state support
- Allows you to specify the c state limit for the processor auto lets the bios automatically configure this setting default auto
- Adjacent cache line prefetch
- Voltage optimization
- Package c state limit
- Hardware prefetcher
- Extremememoryprofile x m p
- Cpu thermal monitor
- Cpu eist function
- C8 state support
- Memory odd ratio 100 133 or 200 266 memory frequency mhz
- Memory odd ratio 100 133 or 200 266
- Memory multiplier tweaker
- Memory frequency mhz
- Memory enhancement settings
- Memory boot mode
- Extremememoryprofile x m p
- Channel interleaving
- Advanced memory settings
- System memory multiplier memory ref clock
- System memory multiplier
- Rank interleaving
- Profileddrvoltage
- Memory timing mode
- Memory ref clock
- Dram voltage control
- Cpu vcore loadline calibration
- Cpu vcore cpu vccsa dram channel a b voltage 3 v 5v 12v cpu vaxg
- Cpu core voltage control
- Chipset voltage control
- Channel a b memory sub timings
- Case open
- Advanced voltage settings
- Advanced power settings
- 3dmark01 enhancement
- Vaxg loadline calibration
- Reset case open status
- Pc health status
- Miscellaneous settings
- Max link speed
- Temperature warning control
- Temperature interval
- Temperature
- Smart fan 5 settings
- Monitor
- Fan speed control
- Fan speed
- Fan fail warning
- Fan control use temperature input
- Fan control mode
- 3 system
- System time
- System language
- System date
- Access level
- Security option
- Hard drive cd dvd rom drive floppy drive network device bbs priorities
- Full screen logo show
- Fast boot
- Bootup numlock state
- Boot option priorities
- 4 bios
- Next boot after ac power loss
- Network stack driver support
- Mouse speed
- Lan pxe boot option rom
- Csm support
- Windows 8 10 features
- Vga support
- Usb support
- Sata support
- Ps2 devices support
- User password
- Storage boot option control
- Secure boot
- Other pci devices
- Administrator password
- Intel platform trust technology ptt
- Initial display output
- Ez raid
- Cpu pcie x16 switc
- Ambient led
- 5 peripherals
- Onboard lan controller lan2
- Offboardsatacontrollerconfiguration
- Intel r bios guard technology
- Sata mode selection
- Port 0 1 2 3 4 5
- Internal graphics
- Hot plug
- Dvmt total gfx mem
- Dvmt pre allocated
- Configuredasesata
- Aggressive lpm support
- 6 chipset
- High precision timer
- Dmi aspm
- Audio controller
- 7 power
- Wake on lan enable
- Platform power management
- Peg aspm
- Pch lan controller lan1
- Pch aspm
- Ioapic 24 119 entries
- Soft off by pwr bttn
- Resume by alarm
- Rc6 render standby
- Power on password
- Power on by mouse
- Power on by keyboard
- Power loading
- Ac back
- Boot override
- 8 save exit
- Saveprofiles
- Save exit setup
- Loadprofiles
- Load optimized defaults
- Exit without saving
- Raid levels
- Configuringtheonboardsatacontroller
- Chapter 3 appendix
- C 1 using ez raid
- Before you begin please prepare the following items
- B configuringsatacontrollermodeinbiossetup
- A installing sata hard drive s in your computer
- 1 configuringaraidset
- 1 configuring a raid set
- C 3 configuringlegacyraidrom
- C 2 uefiraidconfiguration
- Installing the sata raid ahci driver and operating system
- Installing the operating system
- 2 drivers installation
- Weee symbol statement
- Waste electrical electronic equipment weee directive statement
- Restriction of hazardous substances rohs directive statement
- Regulatory statements
- Regulatory notices
- Our commitment to preserving the environment
- Fcc notice u s a only
- Caution
- Canada industry canada ic
- Taiwan ncc wireless statements 無線設備警告聲明
- Korea kcc ncc wireless statement
- Japan wireless statement
- European community directive r tte directive compliance statement
- To submit a technical or non technical sales marketing question please link to http esupport gigabyte com
- Gigabyte esupport
- Contact us
Похожие устройства
-
Gigabyte B760M D3H DDR4Инструкция пользователя -
Gigabyte GA-880GM-D2HИнструкция по работе -
Gigabyte Z890 EAGLEЭксплуатационная инструкция -
Gigabyte Z890 EAGLE WIFI7Инструкция по применению
-
Gigabyte H610M S2HРуководство по использованию -
Gigabyte Z790 AORUS MASTER XРуководство по работе с устройством -
Gigabyte B660M GAMINGИнструкция пользователя -
Gigabyte B550M DS3H ACИнструкция по работе -
Gigabyte GA-Q87TNРуководство по настройке -
Gigabyte GA-H87TNИнструкция по работе
-
Gigabyte GA-B85TNРуководство пользователя
-
Gigabyte GA-H81TNИнструкция по применению
Изучите настройки управления питанием вашего устройства, включая включение по клавиатуре, мыши и настройку пароля. Оптимизируйте энергопотребление и управление системой.