Home
Главная
TSC
Принтер Штрих-Кодов
TTP-244M Pro
Инструкция по эксплуатации Страница: 22

TSC TTP-244M Pro Инструкция по эксплуатации онлайн [22/37] 205284

TSC TTP-342M Pro Инструкция по эксплуатации онлайн [22/37] 205286

5. Close the print head, front panel and printer cover.

6. Set the “post-print action” to “peel”. Peeling will automatically start. Press the

FEED button to test.

Note: Please calibrate the gap/black mark sensor when changing media.

Liner

opening

Label

Liner

Содержание

Manual 1
Thermal transfer direct thermal bar code printer 1
Ttp 244m pro ttp 342m pro 1
Ttp 244me pro ttp 342me pro 1
Caution 4
Caution any changes or modifications not expressly approved by the grantee of this device could void the user s authority to operate the equipment 4
Do not throw the battery in fire 2 do not short circuit the contacts 3 do not disassemble the battery 4 do not throw the battery in municipal waste 5 the symbol of the crossed out wheeled bin indicates that the battery should not be 4
For equipment with rtc cr2032 battery or rechargeable battery pac 4
Placed in municipal waste 4
Risk of explosion if battery is replaced by an incorrect type dispose of used batteries according to the instructions as below 4
The printhead may be hot and could cause severe burns allow the printhead to 4
Warning hazardous moving parts keep fingers and other body parts away caution 4
Appendix a menu control flowchart option 1 5
Contents 5
Diagnostic tool 24 5
Equipment checklist 2 2 printer parts 3 2 buttons and indicators 6 5
Getting started 2 5
Maintenance 27 5
Power on utilities 19 5
Product introduction 1 5
Revise history 28 5
Self test utility 19 4 gap sensor calibration utility 22 4 printer initialization 23 5
Set up 8 5
Setting up the printer 8 3 loading the ribbon 9 3 loading the label 13 3 loading media in peel off mode option 16 3 loading media in cutter mode option 18 5
Start the diagnostic tool 24 5 printer function 25 5
Troubleshooting 26 5
Product introduction 6
Equipment checklist 7
Getting started 7
Printer parts 8
Buttons and indicators 11
Error indicator error paper empty 11
Menu button option function for e series 11
On line indicator 11
Pause select button 11
Power indicator 11
Feed set button 12
And then plug the power cord into a properly grounded receptable 13
Place the printer on a flat secure surface 2 make sure the power switch is off 3 connect the printer to the computer mainframe with the provided printer cable 4 plug the power cord into the ac power cord socket at the rear of the printer 13
Set up 13
Setting up the printer 13
Loading the ribbon 14
Loading the label 18
Loading media in peel off mode option 21
Adjust the label guide to fit the width of the media 4 engage the printer carriage 5 close the printer cover and front panel 6 use diagnostic tool to set the media sensor type and calibrate the selected 23
Loading media in cutter mode option 23
Please refer to section 3 to loarding the media 2 install the label so that it goes when using an external label roll mount 23
Sensor and set the post print action to cutter 23
Through the label feed slot in the direction of the label label and under the ribbon mechanism feed the label through the cutter opening 23
Power on utilities 24
Self test utility 24
Gap sensor calibration utility 27
Printer initialization 28
Diagnostic tool 29
Double click on the diagnostic tool icon 29
Manager command tool included in the diagnostic utility 29
Start the diagnostic tool 29
There are four features printer configuration file manager bitmap font 29
To start the software 29
Tsc s diagnostic utility is an integrated tool incorporating features that enable you to explore a printer s settings status change a printer s settings download graphics fonts and firmware create a printer bitmap font and send additional commands to a printer with the aid of this powerful tool you can review printer status and settings in an instant which makes it much easier to troubleshoot problems and other issues 29
Printer function 30
Select the pc interface connected with bar code printer 2 click the function button to setting 3 the detail functions in the printer function group are listed as below 30
Troubleshooting 31
Maintenance 32
Date content editor 33
Revise history 33
Appendix a menu control flowchart option 34
Continued on next page 34
Flow chart 34
Panel control 34
The following shows the control flowchart of the menu 34
Select 36

TSC TTP-244M Pro Инструкция по эксплуатации онлайн [22/37] 205284

Содержание

Похожие устройства