Indesit Moon SISL 106 S [11/24] Troubleshooting
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Indesit Moon SISL 106 S [11/24] Troubleshooting

Indesit Moon SISL 106 S [11/24] Troubleshooting
GB
GB
11
Troubleshooting
Problem:
The washing machine does not
switch on.
The wash cycle wont start.
The washing machine does not fill
with water (the door locked LED
flashes rapidly).
The machine continuously fills
with water and drains.
The washing machine does not
drain or spin.
The machine vibrates a lot during
the spin cycle.
The washing machine leaks.
The DOOR LOCKED indicator light
flashes rapidly.
Too much foam.
Your washing machine could occasionally fail to work. Before contacting the Technical Assistance Centre
(see Service), make sure that the problem is not easily solved using the following list.
Possible causes / Solutions:
The appliance is not plugged into the socket fully, or is not making
contact.
There is no power in the house.
The washing machine door is not closed properly.
The ON/OFF button has not been pressed.
The START PROGRAMME buttons have not been pressed (they
are still flashing).
The water tap has not been opened.
The water inlet hose is not connected to the tap.
The hose is bent.
The water tap has not been opened.
There is no water supply in the house.
The pressure is too low.
The START PROGRAMME buttons have not been pressed (they
are still flashing).
The drain hose is not fitted at a height between 65 and 100 cm
from the floor ( see Installation).
The free end of the hose is under water (see Installation).
The wall drainage system is not fitted with a breather pipe.
If the problem persists even after these checks, shut off the water
tap, switch the appliance off and contact the Technical Assistance
Service. If the dwelling is on one of the upper floors of a building,
there may be problems relating to water drainage, causing the
washing machine to fill with water and drain continuously. Special
anti-draining valves are available in shops and help to avoid this
inconvenience.
The drain hose is bent (see Installation).
The drainage duct is clogged.
The protective screws (used during transportation) were not
removed when the appliance was installed. Remove the screws
(see Installation).
The machine is not level (see Installation).
The machine is trapped between cabinets and walls (see
Installation).
The water inlet hose is not screwed on properly (see Installation).
The detergent dispenser is blocked (to clean it, see Care and
maintenance).
The drain hose is not fixed in place properly (see Installation).
The drip-tray system is full. Clean the sponge or replace it (see
"Precautions and advice").
Switch off the machine and unplug it, wait for approximately 1
minute and then switch it back on again. The wash cycle will have
to be started again from the beginning. If the problem persists,
contact the Technical Assistance Service.
The detergent is not suitable for machine washing (it should bear
the description for washing machines or hand and machine
wash, or similar instructions).
Too much detergent was used.

Содержание

Похожие устройства

Troubleshooting Q inoesiT Your washing machine could occasionally fail to work Before contacting the Technical Assistance Centre see Service make sure that the problem is not easily solved using the following list Problem Possible causes Solutions The washing machine does not switch on The appliance Is not plugged Into the socket fully or Is not making contact There Is no power In the house The wash cycle won t start The washing machine door Is not closed properly The ON OFF button has not been pressed The START PROGRAMME buttons have not been pressed they are still flashing The water tap has not been opened The washing machine does not fill with water the door locked LED flashes rapidly The water inlet hose is not connected to the tap The hose is bent The water tap has not been opened There is no water supply in the house The pressure is too low The START PROGRAMME buttons have not been pressed they are still flashing The machine continuously fills with water and drains The drain hose is not fitted at a height between 65 and 100 cm from the floor see Installation The free end of the hose is under water see Installation The wall drainage system is not fitted with a breather pipe GB If the problem persists even after these checks shut off the water tap switch the appliance off and contact the Technical Assistance Service If the dwelling is on one of the upper floors of a building there may be problems relating to water drainage causing the washing machine to fill with water and drain continuously Special anti draining valves are available in shops and help to avoid this inconvenience The washing machine does not drain or spin The drain hose is bent see Installation The drainage duct is clogged The machine vibrates a lot during the spin cycle The protective screws used during transportation were not removed when the appliance was installed Remove the screws see Installation The machine is not level see Installation The machine is trapped between cabinets and walls see Installation The washing machine leaks The water inlet hose is not screwed on properly see Installation The detergent dispenser is blocked to clean it see Care and maintenance The drain hose is not fixed in place properly see Installation The drip tray system is full Clean the sponge or replace it see Precautions and advice The DOOR LOCKED indicator light flashes rapidly Switch off the machine and unplug it wait for approximately 1 minute and then switch it back on again The wash cycle will have to be started again from the beginning If the problem persists contact the Technical Assistance Service Too much foam The detergent is not suitable for machine washing it should bear the description for washing machines or hand and machine wash or similar instructions Too much detergent was used 11

Скачать