![Korting KWMT 1070 [4/20] A загрузочный люк b барабан c диспенсер d панель управления e крышка фильтра f ножки](/img/pdf.png)
Korting KWMT 1070 [4/20] A загрузочный люк b барабан c диспенсер d панель управления e крышка фильтра f ножки
![Korting KWMT 0860 [4/20] A загрузочный люк b барабан c диспенсер d панель управления e крышка фильтра f ножки](/views2/1299666/page4/bg4.png)
4
15
SM3130
NOTES AND ADVICE FOR THE USER
DESCRIPTION OF THE APPLIANCE
A - Top cover
B - Drum
C - Detergent compartment
D - Control panel
E - Filter door
F - Feet
EN
Unplug the washing ma-
chine from the power
supply before servicing
and cleaning.
Do not plug-in or un-
plug the machine with
wet hands.
The power supply sock-
et must be earthed and
must comply with the
safety requirements.
Extension leads or mul-
tiple adapters must not
be used to connect the
washing ma chine to
the mains supply..
After the end of each
washing cycle it is ad-
visable to unplug the
machine and shut-off
the water supply.
The washing machine
can be opened only
after the led or display
indicate the end of the
cycle. On some models,
this is indicated by the
start button flashing.
To disconnect the ma-
chine from the power
supply, pull the plug and
not the cable.
Do not expose the ap-
pliance to atmospheric
agents.
1
A
B
C
D
E
F
A - Загрузочный люк
B - Барабан
C - Диспенсер
D - Панель управления
E - Крышка фильтра
F - Ножки
16
SM3130
For transportation, the machine’s oscillating parts are
blocked by two spacers with screws.
Remove these spacers and screws before starting the
machine.
Preserve them for any future moves.
Close the holes with the caps provided inside of the document bag.
INSTALLING THE MACHINE
The machine must be installed by qualified personnel following the manufacturer’s
instructions. Incorrect installation can lead to injuries for persons and damage to
objects.
When deciding where to install the washing machine, consider the following advice:
▼ The room must have a water and electrical system. (Remember that cables
and hoses at the back of the washing machine must not be crushed).
▼ The washing machine must be placed on a flat and solid surface.
▼ Do not install the machine in a room where the temperature could go below
3°C.
▼ Place the machine in the chosen location and remove external packaging (fig.
2).
▼ Lift the washing machine and remove the polystyrene base and the plastic
spacer (fig. 3).
This appliance is intended to be used in household and similar applications such as:
▼ Staff kitchen areas in shops, offices and other working environments;
▼ Farm houses;
▼ By clients in hotels, motels and other residential type environments;
▼ Bed and breakfast type environments.
EN
3
4
2
5
▼ Incline the washing machine and extract the two internal polystyrene corner
pieces (if present) by pulling the two cardboard strips, first E and then F (fig.5).
▼ Remove the polystyrene spacer (fig. 6).
F
E
6
UNPACKING AND UNBLOCKING THE MACHINE
16
SM3130
For transportation, the machine’s oscillating parts are
blocked by two spacers with screws.
Remove these spacers and screws before starting the
machine.
Preserve them for any future moves.
Close the holes with the caps provided inside of the document bag.
INSTALLING THE MACHINE
The machine must be installed by qualified personnel following the manufacturer’s
instructions. Incorrect installation can lead to injuries for persons and damage to
objects.
When deciding where to install the washing machine, consider the following advice:
▼ The room must have a water and electrical system. (Remember that cables
and hoses at the back of the washing machine must not be crushed).
▼ The washing machine must be placed on a flat and solid surface.
▼ Do not install the machine in a room where the temperature could go below
3°C.
▼ Place the machine in the chosen location and remove external packaging (fig.
2).
▼ Lift the washing machine and remove the polystyrene base and the plastic
spacer (fig. 3).
This appliance is intended to be used in household and similar applications such as:
▼ Staff kitchen areas in shops, offices and other working environments;
▼ Farm houses;
▼ By clients in hotels, motels and other residential type environments;
▼ Bed and breakfast type environments.
EN
3
4
2
5
▼ Incline the washing machine and extract the two internal polystyrene corner
pieces (if present) by pulling the two cardboard strips, first E and then F (fig.5).
▼ Remove the polystyrene spacer (fig. 6).
F
E
6
UNPACKING AND UNBLOCKING THE MACHINE
16
SM3130
For transportation, the machine’s oscillating parts are
blocked by two spacers with screws.
Remove these spacers and screws before starting the
machine.
Preserve them for any future moves.
Close the holes with the caps provided inside of the document bag.
INSTALLING THE MACHINE
The machine must be installed by qualified personnel following the manufacturer’s
instructions. Incorrect installation can lead to injuries for persons and damage to
objects.
When deciding where to install the washing machine, consider the following advice:
▼ The room must have a water and electrical system. (Remember that cables
and hoses at the back of the washing machine must not be crushed).
▼ The washing machine must be placed on a flat and solid surface.
▼ Do not install the machine in a room where the temperature could go below
3°C.
▼ Place the machine in the chosen location and remove external packaging (fig.
2).
▼ Lift the washing machine and remove the polystyrene base and the plastic
spacer (fig. 3).
This appliance is intended to be used in household and similar applications such as:
▼ Staff kitchen areas in shops, offices and other working environments;
▼ Farm houses;
▼ By clients in hotels, motels and other residential type environments;
▼ Bed and breakfast type environments.
EN
3
4
2
5
▼ Incline the washing machine and extract the two internal polystyrene corner
pieces (if present) by pulling the two cardboard strips, first E and then F (fig.5).
▼ Remove the polystyrene spacer (fig. 6).
F
E
6
UNPACKING AND UNBLOCKING THE MACHINE
16
SM3130
For transportation, the machine’s oscillating parts are
blocked by two spacers with screws.
Remove these spacers and screws before starting the
machine.
Preserve them for any future moves.
Close the holes with the caps provided inside of the document bag.
INSTALLING THE MACHINE
The machine must be installed by qualified personnel following the manufacturer’s
instructions. Incorrect installation can lead to injuries for persons and damage to
objects.
When deciding where to install the washing machine, consider the following advice:
▼ The room must have a water and electrical system. (Remember that cables
and hoses at the back of the washing machine must not be crushed).
▼ The washing machine must be placed on a flat and solid surface.
▼ Do not install the machine in a room where the temperature could go below
3°C.
▼ Place the machine in the chosen location and remove external packaging (fig.
2).
▼ Lift the washing machine and remove the polystyrene base and the plastic
spacer (fig. 3).
This appliance is intended to be used in household and similar applications such as:
▼ Staff kitchen areas in shops, offices and other working environments;
▼ Farm houses;
▼ By clients in hotels, motels and other residential type environments;
▼ Bed and breakfast type environments.
EN
3
4
2
5
▼ Incline the washing machine and extract the two internal polystyrene corner
pieces (if present) by pulling the two cardboard strips, first E and then F (fig.5).
▼ Remove the polystyrene spacer (fig. 6).
F
E
6
UNPACKING AND UNBLOCKING THE MACHINE
16
SM3130
For transportation, the machine’s oscillating parts are
blocked by two spacers with screws.
Remove these spacers and screws before starting the
machine.
Preserve them for any future moves.
Close the holes with the caps provided inside of the document bag.
INSTALLING THE MACHINE
The machine must be installed by qualified personnel following the manufacturer’s
instructions. Incorrect installation can lead to injuries for persons and damage to
objects.
When deciding where to install the washing machine, consider the following advice:
▼ The room must have a water and electrical system. (Remember that cables
and hoses at the back of the washing machine must not be crushed).
▼ The washing machine must be placed on a flat and solid surface.
▼ Do not install the machine in a room where the temperature could go below
3°C.
▼ Place the machine in the chosen location and remove external packaging (fig.
2).
▼ Lift the washing machine and remove the polystyrene base and the plastic
spacer (fig. 3).
This appliance is intended to be used in household and similar applications such as:
▼ Staff kitchen areas in shops, offices and other working environments;
▼ Farm houses;
▼ By clients in hotels, motels and other residential type environments;
▼ Bed and breakfast type environments.
EN
3
4
2
5
▼ Incline the washing machine and extract the two internal polystyrene corner
pieces (if present) by pulling the two cardboard strips, first E and then F (fig.5).
▼ Remove the polystyrene spacer (fig. 6).
F
E
6
UNPACKING AND UNBLOCKING THE MACHINE
17
SM3130
EN
INSTALLING THE MACHINE
9
LEVELLING THE WASHING MACHINE
WHERE PROVIDED, use the handling wheel to help moving. To use it, push the lever
on the bottom right moving it to the other side. Move the lever back to the original
position after moving (fig.8).
UNPACKING AND UNBLOCKING THE MACHINE
8
7
▼ Remove the polystyrene spacer (fig. 7).
10
11
CONNECTING TO THE POWER SUPPLY
Make sure that the voltage indicated on the identification plate
attached to the inside of the filter door corresponds to that of the
mains supply (fig. 10)
All cut-outs, electric wiring and mains sockets must have a rating such that
enables them to support the maximum load indicated on the identification plate.
Once the appliance has been installed, it must be connected to the mains supply
through a single-pole switch.
The mains supply to which the appliance is connected must be fitted with an
earthing system. If this is not the case, the manufacturer will not be held liable
for any incidents that may occur (fig. 11).
If the mains socket to which the appliance is connected is faulty or unsuitable,
it must be replaced by a qualified electrician.
The washing machine must not be connected to the mains supply using indirect
methods such as extension leads or multiple adapters.
During maintenance work, the washing machine must be disconnected from
the mains electricity supply.
Having chosen the adapt place, set the adjustable feet well so that the machine is
level (Fig. 9).
Pay particular attention to the choice of the position, to levelling the washing machine
and to securing the counternuts.
If the washing machine is not levelled correctly, it will be instable
and make noise when operating causing damage.
If the machine is placed on a rug, make sure that air circulates freely between the
washing machine and the floor.
17
SM3130
EN
INSTALLING THE MACHINE
9
LEVELLING THE WASHING MACHINE
WHERE PROVIDED, use the handling wheel to help moving. To use it, push the lever
on the bottom right moving it to the other side. Move the lever back to the original
position after moving (fig.8).
UNPACKING AND UNBLOCKING THE MACHINE
8
7
▼ Remove the polystyrene spacer (fig. 7).
10
11
CONNECTING TO THE POWER SUPPLY
Make sure that the voltage indicated on the identification plate
attached to the inside of the filter door corresponds to that of the
mains supply (fig. 10)
All cut-outs, electric wiring and mains sockets must have a rating such that
enables them to support the maximum load indicated on the identification plate.
Once the appliance has been installed, it must be connected to the mains supply
through a single-pole switch.
The mains supply to which the appliance is connected must be fitted with an
earthing system. If this is not the case, the manufacturer will not be held liable
for any incidents that may occur (fig. 11).
If the mains socket to which the appliance is connected is faulty or unsuitable,
it must be replaced by a qualified electrician.
The washing machine must not be connected to the mains supply using indirect
methods such as extension leads or multiple adapters.
During maintenance work, the washing machine must be disconnected from
the mains electricity supply.
Having chosen the adapt place, set the adjustable feet well so that the machine is
level (Fig. 9).
Pay particular attention to the choice of the position, to levelling the washing machine
and to securing the counternuts.
If the washing machine is not levelled correctly, it will be instable
and make noise when operating causing damage.
If the machine is placed on a rug, make sure that air circulates freely between the
washing machine and the floor.
17
SM3130
EN
INSTALLING THE MACHINE
9
LEVELLING THE WASHING MACHINE
WHERE PROVIDED, use the handling wheel to help moving. To use it, push the lever
on the bottom right moving it to the other side. Move the lever back to the original
position after moving (fig.8).
UNPACKING AND UNBLOCKING THE MACHINE
8
7
▼ Remove the polystyrene spacer (fig. 7).
10
11
CONNECTING TO THE POWER SUPPLY
Make sure that the voltage indicated on the identification plate
attached to the inside of the filter door corresponds to that of the
mains supply (fig. 10)
All cut-outs, electric wiring and mains sockets must have a rating such that
enables them to support the maximum load indicated on the identification plate.
Once the appliance has been installed, it must be connected to the mains supply
through a single-pole switch.
The mains supply to which the appliance is connected must be fitted with an
earthing system. If this is not the case, the manufacturer will not be held liable
for any incidents that may occur (fig. 11).
If the mains socket to which the appliance is connected is faulty or unsuitable,
it must be replaced by a qualified electrician.
The washing machine must not be connected to the mains supply using indirect
methods such as extension leads or multiple adapters.
During maintenance work, the washing machine must be disconnected from
the mains electricity supply.
Having chosen the adapt place, set the adjustable feet well so that the machine is
level (Fig. 9).
Pay particular attention to the choice of the position, to levelling the washing machine
and to securing the counternuts.
If the washing machine is not levelled correctly, it will be instable
and make noise when operating causing damage.
If the machine is placed on a rug, make sure that air circulates freely between the
washing machine and the floor.
17
SM3130
EN
INSTALLING THE MACHINE
9
LEVELLING THE WASHING MACHINE
WHERE PROVIDED, use the handling wheel to help moving. To use it, push the lever
on the bottom right moving it to the other side. Move the lever back to the original
position after moving (fig.8).
UNPACKING AND UNBLOCKING THE MACHINE
8
7
▼ Remove the polystyrene spacer (fig. 7).
10
11
CONNECTING TO THE POWER SUPPLY
Make sure that the voltage indicated on the identification plate
attached to the inside of the filter door corresponds to that of the
mains supply (fig. 10)
All cut-outs, electric wiring and mains sockets must have a rating such that
enables them to support the maximum load indicated on the identification plate.
Once the appliance has been installed, it must be connected to the mains supply
through a single-pole switch.
The mains supply to which the appliance is connected must be fitted with an
earthing system. If this is not the case, the manufacturer will not be held liable
for any incidents that may occur (fig. 11).
If the mains socket to which the appliance is connected is faulty or unsuitable,
it must be replaced by a qualified electrician.
The washing machine must not be connected to the mains supply using indirect
methods such as extension leads or multiple adapters.
During maintenance work, the washing machine must be disconnected from
the mains electricity supply.
Having chosen the adapt place, set the adjustable feet well so that the machine is
level (Fig. 9).
Pay particular attention to the choice of the position, to levelling the washing machine
and to securing the counternuts.
If the washing machine is not levelled correctly, it will be instable
and make noise when operating causing damage.
If the machine is placed on a rug, make sure that air circulates freely between the
washing machine and the floor.
17
SM3130
EN
INSTALLING THE MACHINE
9
LEVELLING THE WASHING MACHINE
WHERE PROVIDED, use the handling wheel to help moving. To use it, push the lever
on the bottom right moving it to the other side. Move the lever back to the original
position after moving (fig.8).
UNPACKING AND UNBLOCKING THE MACHINE
8
7
▼ Remove the polystyrene spacer (fig. 7).
10
11
CONNECTING TO THE POWER SUPPLY
Make sure that the voltage indicated on the identification plate
attached to the inside of the filter door corresponds to that of the
mains supply (fig. 10)
All cut-outs, electric wiring and mains sockets must have a rating such that
enables them to support the maximum load indicated on the identification plate.
Once the appliance has been installed, it must be connected to the mains supply
through a single-pole switch.
The mains supply to which the appliance is connected must be fitted with an
earthing system. If this is not the case, the manufacturer will not be held liable
for any incidents that may occur (fig. 11).
If the mains socket to which the appliance is connected is faulty or unsuitable,
it must be replaced by a qualified electrician.
The washing machine must not be connected to the mains supply using indirect
methods such as extension leads or multiple adapters.
During maintenance work, the washing machine must be disconnected from
the mains electricity supply.
Having chosen the adapt place, set the adjustable feet well so that the machine is
level (Fig. 9).
Pay particular attention to the choice of the position, to levelling the washing machine
and to securing the counternuts.
If the washing machine is not levelled correctly, it will be instable
and make noise when operating causing damage.
If the machine is placed on a rug, make sure that air circulates freely between the
washing machine and the floor.
18
SM3130
INSTALLING THE MACHINE
EN
WATER CONNECTION
The mains water pressure must be between 0.05 and 1.00 MPa
(0,5 - 10 bar.)
▼ Before connection, open the tap and let the water run in order to clean the pipes
from impurities like sand and rust. (This operation is very important when the
washing machine has been inactive for a long time or when connected to new
piping).
▼ The water supply hose must be connected to the cold water outlet with a 3/4”
threaded opening.
▼ Connect the supply hose (fig. 12/13).
Use the new hose provided with the machine. Do not reuse the
old one.
Do not connect to the hot water supply.
▼ The water supply tap must be completely open during washing.
▼ Connect the drain hose to a drain piping or wall drain between 60 and 90 cm
from the ground without squeezing it (fig.14).
▼ If the water drains directly into the drain piping, the free end of the machine
hose must be inserted in the piping with an inside diameter no smaller than 40
mm.
▼ If water is drained into the washbasin or another drain, the free end of the hose
must be previously reinforced at the bending with an appropriate hook, provided
with the washing machine. Then place the hose at the edge of the washbasin
and fix the hook to prevent the hose from falling (fig. 15). The washbasin must
have its drain clean to allow water to drain freely.
12
13
14
15
INSTALLING THE MACHINE
Do not insert or remove the plug from the mains socket with wet hands.
If the power supply cable is damaged in any way, contact the appropriate specialised service centre.
The plug used to connect the machine to the power supply must never be fixed behind the machine,
but must be in a position easily accessible in an emergency.
18
SM3130
INSTALLING THE MACHINE
EN
WATER CONNECTION
The mains water pressure must be between 0.05 and 1.00 MPa
(0,5 - 10 bar.)
▼ Before connection, open the tap and let the water run in order to clean the pipes
from impurities like sand and rust. (This operation is very important when the
washing machine has been inactive for a long time or when connected to new
piping).
▼ The water supply hose must be connected to the cold water outlet with a 3/4”
threaded opening.
▼ Connect the supply hose (fig. 12/13).
Use the new hose provided with the machine. Do not reuse the
old one.
Do not connect to the hot water supply.
▼ The water supply tap must be completely open during washing.
▼ Connect the drain hose to a drain piping or wall drain between 60 and 90 cm
from the ground without squeezing it (fig.14).
▼ If the water drains directly into the drain piping, the free end of the machine
hose must be inserted in the piping with an inside diameter no smaller than 40
mm.
▼ If water is drained into the washbasin or another drain, the free end of the hose
must be previously reinforced at the bending with an appropriate hook, provided
with the washing machine. Then place the hose at the edge of the washbasin
and fix the hook to prevent the hose from falling (fig. 15). The washbasin must
have its drain clean to allow water to drain freely.
12
13
14
15
INSTALLING THE MACHINE
Do not insert or remove the plug from the mains socket with wet hands.
If the power supply cable is damaged in any way, contact the appropriate specialised service centre.
The plug used to connect the machine to the power supply must never be fixed behind the machine,
but must be in a position easily accessible in an emergency.
Содержание
- Maintenance 2
- Troubleshooting 2
- Общие рекомендации 3
- A top cover 4
- A загрузочный люк b барабан c диспенсер d панель управления e крышка фильтра f ножки 4
- After the end of each washing cycle it is ad visable to unplug the machine and shut off the water supply 4
- All cut outs electric wiring and mains sockets must have a rating such that enables them to support the maximum load indicated on the identification plate 4
- B drum 4
- C detergent compartment 4
- Connecting to the power supply 4
- D control panel 4
- Description of the appliance 4
- Do not expose the ap pliance to atmospheric agents 4
- Do not plug in or un plug the machine with wet hands 4
- During maintenance work the washing machine must be disconnected from the mains electricity supply 4
- E filter door 4
- Extension leads or mul tiple adapters must not be used to connect the washing ma chine to the mains supply 4
- F feet 4
- Having chosen the adapt place set the adjustable feet well so that the machine is level fig 9 4
- If the machine is placed on a rug make sure that air circulates freely between the washing machine and the floor 4
- If the mains socket to which the appliance is connected is faulty or unsuitable it must be replaced by a qualified electrician 4
- If the washing machine is not levelled correctly it will be instable and make noise when operating causing damage 4
- Installing the machine 4
- Levelling the washing machine 4
- Make sure that the voltage indicated on the identification plate attached to the inside of the filter door corresponds to that of the mains supply fig 10 4
- Notes and advice for the user 4
- Once the appliance has been installed it must be connected to the mains supply through a single pole switch 4
- Pay particular attention to the choice of the position to levelling the washing machine and to securing the counternuts 4
- Remove the polystyrene spacer fig 7 4
- The mains supply to which the appliance is connected must be fitted with an earthing system if this is not the case the manufacturer will not be held liable for any incidents that may occur fig 11 4
- The power supply sock et must be earthed and must comply with the safety requirements 4
- The washing machine can be opened only after the led or display indicate the end of the cycle on some models this is indicated by the start button flashing 4
- The washing machine must not be connected to the mains supply using indirect methods such as extension leads or multiple adapters 4
- To disconnect the ma chine from the power supply pull the plug and not the cable 4
- Unpacking and unblocking the machine 4
- Unplug the washing ma chine from the power supply before servicing and cleaning 4
- Water connection 4
- Where provided use the handling wheel to help moving to use it push the lever on the bottom right moving it to the other side move the lever back to the original position after moving fig 4
- Before placing the clothes in the washing machine and selecting the wash programme examine the symbols on the manufacturer s label the table reported below will provide a useful guide to reading the symbols 5
- Clean using a soft cloth soaked in ethyl alcohol take care not to spread the stain 5
- Cleaning the filter 5
- Cleaning the washing machine 5
- Delicately soap the stain use diluted bleach good results can be obtained on woollen fabrics using 90 alcohol 5
- Do not allow the paint to dry rub the area with the solvent recommended by the paint manufacturer e g water turps trichlo roethylene soap and then rinse 5
- Follow the instructions for mould and damp 5
- If the fabric supports the use of bleach carry out a wash cycle adding bleach otherwise soak the soiled part in hydrogen peroxide 10 volumes and leave for 10 to 15 minutes 5
- Information before use 5
- Installing the machine 5
- Maintenance 5
- Place a sheet of absorbent paper on the stained material then dampen the back of the fabric with acetone frequently changing the absorbent paper placed over the stain continue in this manner until the stain has disappeared 5
- Put into soak in cold water with added salt then wash with washing soap 5
- Recovering fallen items between drum and basin 5
- Rub ice over the fabric scrape away as much chewing gum as possible and then rub with a piece of cotton soaked in acetone 5
- Scrape the wax using a rounded point in order not to damage the fabric then with the fabric placed between two pieces of ab sorbent paper run a hot iron over the stain 5
- Spread a little fresh butter over the stain allow to stand and then wash with oil of turpentine 5
- Stains exist that cannot be removed by machine washing alone before trying to remove any type of stain by hand first try the removal procedure on a small area of hidden fabric start from the edge of the stain and working inwards this will prevent a dark ring from forming around the site of the stain a few methods to adopt for removing stains are reported below 5
- Stains on cotton or wool can be elimi nated using a cloth soaked in ether stains on silk require the use of trichloroethylene 5
- Use of detergent 5
- Use products specially designed for rust stains following the manufacturer s instruc tions written on the packet 5
- Using the washing machine 5
- Washing machine use 5
- Water connection 5
- Глажка до 100 5
- Глажка до 150 5
- Глажка до 200 5
- Деликатная стирка 5
- Макс температура 30 c 5
- Макс температура 40 c 5
- Макс температура 60 c 5
- Макс температура 95 c 5
- Не гладить 5
- Не отбеливать 5
- Не подвергать сухой чистке 5
- Не сушить в стиральной машине 5
- Обычная стирка 5
- Отбеливать в холодной воде 5
- Ручная стирка 5
- Сухая чистка с бензином с этиловым спиртом либо r113 5
- Сухая чистка с растворителем 5
- Сухая чистка с этиловым перхлоратом бензином этиловым спиртом r113 r111 5
- Сушить в стиральной машине при низкой температуре 5
- Сушить в стиральной машине при нормальной температуре 5
- Сушить вертикально 5
- Сушить горизонтально 5
- Сушить на вешалке 5
- Таблица символов на бирках изделий 5
- Только сухая чистка 5
- Общие правила безопасности 6
- Техника безопасности 6
- Установка 7
- Эксплуатация и уход 8
- E 03 e 02 обратитесь в авторизованный сервисный центр 11
- Код ошибки возможные причины и практические решения 11
- Стиральная машина не работает дисплей светится 11
- Стиральная машина не сливает воду барабан не вращается 11
- Стиральная машина неприрывно набирает и сливает воду 11
- Устранение неисправностей 11
- Белье после стирки становится перекрученым 12
- Крышка стиральной машины не открывается 12
- После стрики в диспенсере остается порошок 12
- Проблема возможные причины и практические решения 12
- Сильные вибрации шумы при отжиме 12
- Стиральная машина не работает дисплей не светится 12
- Стиральная машина останавливается во время стирки 12
- Wash in the correct way 14
- Washing guide 14
- Управление и программы стирки 14
- Program table 16
- Таблица программ 16
- Технические параметры 17
- Гарантия 18
- Um kwmt 1070 1485 0860 ver 1 19
- Информация от производителя 19
Похожие устройства
- Korting KWMT 0860 Руководство пользователя
- Korting KSI 17895 CNFZ Руководство пользователя
- Korting KSI 8256 Руководство пользователя
- Korting KSI 8251 Руководство пользователя
- Korting KSI 8259 F Руководство пользователя
- Supra STV-LC55LT0010F Руководство по эксплуатации
- Supra STV-LC50LT0010F Руководство по эксплуатации
- Supra STV-LC40LT0010F Руководство по эксплуатации
- Supra STV-LC40LT0011F Руководство по эксплуатации
- Supra STV-LC32LT0060F Руководство по эксплуатации
- Supra STV-LC32ST3001F Руководство по эксплуатации
- Supra STV-LC40ST1000F Руководство по эксплуатации
- Supra STV-LC32ST2000W Руководство по эксплуатации
- Supra STV-LC24LT0030W Руководство по эксплуатации
- Supra STV-LC40LT0050F Руководство по эксплуатации
- Supra STV-LC24LT0020F Руководство по эксплуатации
- Supra STV-LC24LT0010W Руководство по эксплуатации
- Supra PHS-1002S Руководство по эксплуатации
- Supra PHS-1603M Руководство по эксплуатации
- Lenovo IdeaCentre AIO510-22ISH, F0CB00T2RK Инструкция по эксплуатации
Скачать
Случайные обсуждения