Liebherr G 5216 [3/5] Climate rating
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Liebherr G 5216 [3/5] Climate rating

Liebherr G 5216 [3/5] Climate rating
7
GB
Switching the appliance on and o
Switching on: Press the ON / OFF button so that the
temperature display lights up/ashes. When the appliance
is switched on for the rst time and while it is still warm,
the display will contain dashes until the temperature falls
below 0°C.
Switching o: Press the ON / OFF button for approx. two seconds
so that the temperature display goes out.
Operating and control elements
1 Temperature display
2 Temperature buttons
3 On/O button
4 SuperFrost button
5 Audible warning on/o button
6 Child-proof lock
Setting the temperature
To increase the temperature
Press the Up button.
To reduce the temperature
Press the Down button.
- When pressing one of the buttons for the first time, the display
will start to flash.
- Pressing this button again enables you to change the temperature
setting.
- The electronic controls will switch over automatically about 5 sec-
onds after the last time you pressed the button, and the actual
temperature will be displayed.
- The temperature can be set at between -14°C and -28°C.
If
F 3 appears in the display, the appliance has a fault. Consult the
customer serv ice department indicating the fault number displayed.
Setting up
• Do not place appliance in areas of direct sunlight or next to a
stove, heater or similar object.
• The floor on which the appliance stands should be horizontal and
level.Compensate for uneven floors with the adjustable feet.
• Always ensure good ventilation. Do not cover ventilation openings
or grille.
• Do not place heat-emitting appliances, e.g. microwave oven,
toaster, etc., on top of the freezer.
• Standard EN 378 specifies that the room in which you install your
appliance must have a volume of 1 m
3
per 8 g of R 600a refrigerant
used in the appliance, so as to avoid the formation of inflammable
gas/air mixtures in the room where the appliance is located in the
event of a leak in the refrigerant circuit. The quantity of refrigerant
used in your appliance is indicated on the type plate on the inside
of the appliance.
• Always install the appliance directly against the wall.
Saving energy
- Always ensure good ventilation. Do not cover ventilation openings
or grille.
- Do not place appliance in areas of direct sunlight or next to a
stove, heater or similar object.
- The energy consumption depends on the installation conditions,
e.g. the ambient temperature.
- Keep the time the appliance is open to a minimum.
- Store food logically.
- Ensure that all food is well packed and covered for storage. This
will prevent frost from forming.
- First cool warm food to room temperature before storing it.
- If there is a thick layer of frost in the appliance: defrost the appli-
ance.
Accumulated dust increases the energy consumption:
- Once a year, dust the refrigerating unit together with the metal
grille of the heat exchanger at the back of the appliance.
Dimensions
A= 1725 mm
B= 750 mm
C= 760 mm
D= 1447 mm
E= 790 mm
Climate rating
The climate rating indicates the room tem-
perature at which the appliance may be
operated in order to achieve full refrigeration
performance.
The climate rating is indicated on the type
plate.
The position of the type plate is shown in
the section entitled Description of the appliance.
Climate rating Room temperature
SN +10°C to +32°C
N +16°C to +32°C
ST +16°C to +38°C
T +16°C to +43°C
SN-ST +10°C to +38°C
SN-T +10°C to +43°C
Do not operate the appliance outside the specied room
temperature range.
Electrical connection
Only operate the appliance with alternating current (AC).
The permissible voltage and frequency are indicated on the type
plate. The position of the type plate is shown in the section entitled
Description of the appliance.
The socket must be properly earthed and protected by a fuse.
The tripping current of the fuse must be between 10 A and 16 A.
The socket must not be situated behind the appliance and must
be easily accessible.
Do not connect the appliance using an exten-
sion cable or extension socket.
Do not use stand-alone inverters (conversion
of direct current to alternating current/three-
phase current) or energy-saving plugs. Risk
of damage to the electronic control system!

Содержание

Похожие устройства

Скачать