Home
Главная
Nemco
Картофелерезка
55050AN-WCT
Инструкция по эксплуатации Страница: 1

Nemco 55050AN-WCT Инструкция по эксплуатации онлайн

Nemco 55050AN-CT Инструкция по эксплуатации онлайн

Operating and Maintenance Instructions

Model: 55050AN

Spiral Fry™ Potato Cutter

55050AN-G

Fine Cut Garnish Cutter

55050AN-R Ribbon Fry Cutter

55050AN-WR Wavy Cut Ribbon Fry Cutter

55050AN-CT Chip Twister

55050AN-WCT Wavy Chip Twister

IMPORTANT

1. To get the best operation and life from your machine, please read and comply with these instructions.

2. Clean machine thoroughly before and after each use using cleaning instructions below.

3. Minimize the use of alkaline cleaners as they may cause pitting and dulling of the finish.

SAFETY INSTRUCTIONS

Remember that the blades are VERY SHARP; be careful when handling and operating the machine to keep hands away from

the cutting edges.

PREPARATION

1. Remove the mounting base from the machine as it is received and install it on a tabletop. Insert the SUPPORT STAND into the

MOUNTING BASE and secure in place with the LOCK SCREW.

2. If unit fails to operate properly when first used call NEMCO customer service at 1-800-782-6761

OPERATION

of Spiral Fry™

First disengage the DRIVE LEVER by lifting it off the DRIVE SCREW and letting it hang down from the SUPPORT ROD. Pull back on

CRANK until the back face of the DRIVE PLATE mounted on the rear of the DRIVE SCREW strikes the face of the stand. Push the

large diameter end of the product onto the fingers of the DRIVE PLATE and then push product, drive plate and crank forward until

CENTER SCREW is embedded in the product. Engage DRIVE LEVER by placing it over the DRIVE SCREW. Then turn CRANK

clockwise until product is completely processed. Disengage DRIVE LEVER, pull DRIVE SCREW back, remove product heel and

repeat the process.

Note: For best results, place a hand lightly on the DRIVE LEVER while turning the crank. When the DRIVE LEVER rises, stop

cranking; lift the DRIVE LEVER and pull the CRANK and DRIVE SCREW back to accept the next product. Do not continue

to crank after the DRIVE LEVER rises.

OPERATION OF RIBBON FRY, GARNISH CUTTER, & WAVY CUT

Pull back on CRANK until back face of the DRIVE PLATE mounted on the rear of the DRIVE SHAFT strikes the face of the STAND.

Push the large diameter end of the product on to the fingers of the DRIVE PLATE and then push the DRIVE PLATE and CRANK

forward until the round blade is embedded in the product. Then press the CRANK forward firmly while turning CRANK clockwise

until product is completely processed. The DRIVE LEVER is used on the spiral fry only.

CLEANING

Loosen LOCK SCREW and remove the machine from the MOUNTING BASE. The machine can be cleaned by immersing, pressure

spraying or putting it through a dishwasher.

When necessary, the machine can be easily disassembled for further cleaning as follows:

1. Remove FRONT PLATE ASSEMBLY by removing the WING NUTS.

2. The BLADES can be removed with a screwdriver. Note: CENTER SCREW has a LEFT HAND THREAD so turn

clockwise to remove.

3. Remove the DRIVE PLATE by unthreading it from the DRIVE SCREW.

4. The SUPPORT RODS can be unthreaded from the SUPPORT STAND ASSEMBLY.

5. To reassemble, reverse the procedure.

PREVENTATIVE MAINTENANCE

1. All BLADES are made of hardened Stainless Steel. They can be re-sharpened with a file or sharpening stone (except for Wavy

Cut).

2. Clean machine after each use.

Nemco 55050AN-WCT Инструкция по эксплуатации онлайн

Содержание

Похожие устройства