Home
Главная
Liebherr
Шкаф морозильный
GGv 5860
Инструкция по эксплуатации Страница: 4

Liebherr GGv 5860 [4/7] Electrical connection

Switching the appliance on and o

Switching on: Press the ON/OFF button so that the

temperaturedisplaylightsup/ashes.Whentheappli-

anceisswitchedonforthersttimeandwhileitisstill

warm, the display will contain dashes until the temperature

fallsbelow0°C.

Switching o: Press the ON/OFF button for approx. two seconds

so that the temperature display goes out.

Audible warning signal

The appliance is equipped with an alarm function.

Audible door alarm:

This sounds when the door has been left open for longer

than about 180 seconds. Press the audible warning on/

obuttontocancelthealarm.Thealarmswitchesback

to standby when the door is shut.

Audible/visual temperature alarm:

It sounds when it is not cold enough in the freezer compartment.

The temperature display w i l l a l s oa s h.Theau d i b l e w a r n i n g d e v i c e 

isswitchedobypressingthe"ALARM" button. The temperature

displaywillcontinuetoashuntilthecauseofthealarmhasbeen

rectied.

This can be caused by:

• thefreezerdoorbeingleftopenforalongtime,allowingwarm

ambient air to enter;

• alongpowerfailure;

• afaultintheappliance.

In each case, make sure food has not thawed or perished.

Operating elements

1 Temperature display

2 Temperature setting buttons

3On/Obutton

4Audiblewarningon/obutton

5 Childlock

6 Appliance is defrosting.

Note

 No refrigeration takes place during the defrost

phase, and the operating noise changes.

Setting the temperature

To reduce the temperature: Press the DOWN

button.

To increase the temperature: Press the UP

button.

- Whileyouareenteringthetemperature,thesettemperaturewill

flash on the display.

- Whenyoupressthetemperaturesettingbuttonsforthefirsttime,

the most recent setting is displayed.

- Youcanchangethesettingsinincrementsof1°Cbybrieflypress-

ing the buttons again.

- The electronic controls will switch over automatically about 5 sec-

onds after the last time you pressed the button, and the actual

temperature in the freezer will be displayed.

- Thetemperaturecanbesetatbetween-14°Cand-28°C.

F3, F4 or HE appears in the display, the appliance has a fault.

Consult the customer serv ice department indicating the fault

number displayed.

Power failure FrostControl display

If nA appears in the display, this means that the

freezer temperature has risen too high during the last

few hours or days due to a power failure.

If you press the "ALARM" button whilst the display

is reading nA, the highest temperature registered

during the power failure will be displayed. Check the quality of the

food and its suitability for consumption in case it has become too

warm or even defrosted.

The highest temperature will appear for appox. 1 minute. After that,

the actual temperature in the freezer will re-appear. The display

canbeswitchedobypressingthe"ALARM" button.

Electrical connection

Only operate the appliance with alternating current (AC).

The permissible voltage and frequency are indicated on the type

plate. The position of the type plate is shown in the section entitled

Description of the appliance.

The socket must be properly earthed and protected by a fuse.

The tripping current of the fuse must be between 10 A and 16 A.

The socket must not be situated behind the appli-

ance and must be easily accessible.

Do not connect the appliance using an exten-

sion cable or extension socket.

Do not use stand-alone inverters (conversion of

d.c. to a.c./three-phase) or energy saving plugs.

Riskofdamagetotheelectroniccontrolsystem!

Liebherr GGv 5860 [4/7] Electrical connection

Содержание

Похожие устройства