Home
Главная
Dimplex
Камин
Bingham
Инструкция по эксплуатации Страница: 7

Dimplex Bingham Инструкция по эксплуатации онлайн [7/16] 277306

Before installing this appliance, we recommend that;

1. Choose which style of Bingham you require and make the

required adjustments to the appliance

2. If the appliance is to be installed in an existing chimney

breast, ensure that the chimney is cleaned by a competent

chimney sweep and block o the chimney  ue.

This procedure is important for the e cient operation of

appliance.

Installation.

Ensure that all packing items are removed (read any

warning labels carefully).

Retain all packing for possible future use, in the event of

moving or returning the appliance to your supplier.

Under the appliance there are four adjustable supports

provided for levelling, where the base of the  replace opening

is raised above the level of the hearth.

You are now ready to install the electric  re. Make sure the unit

is switched OFF.

Using the correct  xings for your wall  x the wall bracket to

the wall. With two persons hold the  re by the sides and gently

manoeuvre into position. Plug the  re into a 13amp/240 volt

outlet. Ensure that the supply cable exits at the front of the

 re, at the right or left hand corner to suit your supply socket

location and is not trapped under the  re such that it might

become damaged, also that the plug is accessable after

installation.

Before using the manual controls  rstly  ll the water tank

(See ‘Maintenance’, ‘Filling the water tank’).

Manual Controls.

The Opti-myst Manual controls are located behind the drawer

front. Slide out the drawer to access the controls. (See Fig. 2 for

Manual Control lay out)

Switch ‘A’:- Controls the electricity supply to the heater.

Note: This switch must be in the ‘ON’ ( I ) position for the

appliance to operate, with or without heat.

Switch ‘B’:- Controls the functions of the  re.

Press

once to turn on  ame e ect. This will be indicated

by one beep.

Although the main lights operate immediately it will take a

further 30 seconds before the  ame e ect starts.

Press it again to give  ame e ect and heat. This will be

indicated by two beeps.

Press it again to return to  ame e ect only.

This will be indicated by one beep.

Press to put  re in to standby mode.

This will be indicated by one beep.

Switch ‘C’:- Controls the mist extractor motor.

There are two speeds for the mist extractor motor, low and

high. This function is required to eliminate concensation on

the glass. When the unit is switched on the mist extractor

motor will run at high speed for 1 minute and then will default

to the low setting.

Thumb Wheel ‘D’:- Controls the mist output.

Turning the wheel upwards will increase the amount of mist

produced and turning the wheel downwards decreaces the

amount of mist produced.

Note: Should condendsation appear on the glass, simply turn

down the mist and switch the mist extractor motor to high

speed until the condensation has been eliminated.

When the water tank is empty the main lamps will go out. See

instructions under ‘Maintenance’, ‘Filling the water tank’. When

this procedure is complete, the main lamps will illuminate but

it will take approx 30 seconds before the  ames return.

Remote Control Operation

On the control panel, Switch A (see Fig. 2) must be in the ‘ON’ ( I

) position in order for the remote control to operate. There are 3

buttons on the remote control. (See Fig. 7)

To operate correctly the remote must be pointed towards the

front of the fuel e ect.

The remote control functions are as follows:

Press once to turn on Flame e ect only.

This will be indicated by one beep.

Press once to turn on Heat and Flame e ect.

This will be indicated by two beeps.

Standby

This will be indicated by one beep.

Battery Information.

1. Unclip the battery cover on the back of the remote control.

(See Fig. 7)

2. Install AAA batteries into the remote control.

3. Replace the battery cover.

Discard leaky batteries.

Dispose of batteries in the proper manner according to

national and local regulations.

Any battery may leak electrolyte if mixed with a di erent

battery type, if inserted incorrectly, if all the batteries are

not replaced at the same time, if disposed of in a  re, or if

an attempt is made to charge a battery not intended to be

recharged.

Thermal safety cut-out

A thermal safety cut-out is incorporated in the fan heater to

prevent damage due to overheating. This can happen if the

heat outlet is restricted in any way or if the chimney  ue has

not been blocked o e ectively. If the cut-out operates, unplug

the heater from the socket outlet and allow approximately 10

minutes before reconnecting. Before switching the heater

back on remove any obstruction that may be restricting the

heat outlet, then continue normal operation.

Caution: In order to avoid hazard due to inadvertent resetting

of the thermal cutout, this appliance must not be powered

through an external switching device, such as a timer, or

connected to a switch that is regularly switched on and o by

the utility.

This heater is not equipped with a thermostat to control the

room temperature.

Tips for using your appliance.

1. Only pull out the drawer when its time to re ll the water

tank or change a lamp, otherwise it may lead to excess

water in the sump and reduced  ame e ect. If this happens

empty the water from the sump as instructed under

Dimplex Bingham Инструкция по эксплуатации онлайн [7/16] 277306

Содержание

Похожие устройства