Stadler Form Paul Black [7/33] If the supply cord is damaged it must be replaced by the manufacturer or its service agent or a qualified person in order to avoid a hazard

Stadler Form Paul Black [7/33] If the supply cord is damaged it must be replaced by the manufacturer or its service agent or a qualified person in order to avoid a hazard
distance of at least 100 cm to showers, bathtubs, water faucets, washba-
sins, etc.
1. Having set up Paul in the desired position connect the cable (1) to the
household supply socket.
2. First, push the main switch for power supply (4) on the back of the ap-
pliance.
3. Switch on the appliance by pressing the On/Off button (6). The target
temperature appears on the display.
4. The target temperature can be changed from 0 °C (cooling mode) to
26 °C or maximum «Hi» by making a vertical sliding movement across the
right-hand control panel for selection of temperature (8) «Temperature».
The heating mode is active from 1 ° – 26 °C & «Hi». The digit flashes in
configuration mode. Making a sliding movement upwards or typing «+»
in the upper field increases the target temperature. Making a sliding
movement downwards or typing «» in the lower field reduces the tar-
get temperature. The setting is saved if no change occurs on the control
panel for selection of temperature for three seconds. The current room
temperature is subsequently shown on the display.
Info: The appliance switches off the heating element when the target
temperature is reached and the temperature indicator flashes on the dis-
play. The ventilator remains switched on at the lowest level in order to
monitor room temperature. The appliance switches on again if the room
temperature recorded drops below the set target temperature.
5. Cooling mode: the heating element switches off if the temperature is set
to 0 °C and the ventilator blows cool air out of the appliance. The LED
light (7) changes from red to blue. There is no temperature shown on the
display in cooling mode.
6. The heat output level can be changed from low to high by making a
vertical sliding movement across the left-hand control panel for selec-
tion of heat output level (9) «Power Level». The display flashes during
the input process. Making a sliding movement upwards or typing «+» in
the upper field increases the output level. Making a sliding movement
downwards or typing «» in the lower field reduces the output level. The
setting is saved if no change occurs on the control panel for selection
of heat output level for three seconds. The current room temperature is
subsequently shown on the display.
7. Auto mode is activated by pressing the «Auto Mode» button (10). «Auto
Mode» is shown in the display. The preset target temperature of 22 °C
can be changed using the right-hand control panel for selection of tem-
perature (8). The heat output level is selected automatically in auto
mode - depending on the room temperature. The smaller the difference
between the room temperature and the target temperature, the smaller
the heat output level selected. We refer to this as «Adaptive Heat
TM
»
technology and we have filed for an international patent. This allows
Paul to make sure that the target temperature is reached, quickly and
efficiently, and maintained. Paul thus prevents a sharp temperature drop
and prevents the appliance from being constantly switched on and off.
Auto mode is deactivated if the heat output level is changed manually
(9).
Info: The appliance switches off the heating element when the target
temperature is reached and the temperature indicator flashes on the
display.
Stadler Form refuses all liability for loss or damage which arises as a
result of failure to follow these operating instructions.
The appliance is only to be used in the home for the purposes described
in these instructions. Unauthorised use and technical modifications to the
appliance can lead to danger to life and health.
Never submerge the unit in water (danger of short circuiting).
Never run a defective unit (e.g. supply cord).
Never touch energized parts.
Only connect the cable to alternating current. Observe the voltage infor-
mation given on the appliance. Do not use extension cords.
The heater must not be located directly below a socket-outlet.
Do not open the appliance (repairs only by service agents).
The appliance is dripping water-proof (vertical) according to the classifi-
cation IP21 and may only be used in bathrooms in case you keep a safety
distance of at least 100 cm to the following objects: bathtubs, showers,
swimming pools, water faucets, wash basins, etc.
Do not run the power cord over sharp edges and make sure that it does
not get trapped. Do not pull the plug from the socket with wet hands or by
holding on to the power cord.
Do not place the appliance near a heat source. Do not subject the power
cord to direct heat (such as a heated hotplate, open flames, hot iron sole
plates or heaters for example). Protect power cords from oil.
Please make sure that the used socket remains accessible.
Do not run the heater on an uneven or soft surface.
CAUTION: In order to avoid a hazard due to inadvertent resetting of the
thermal cut-out, this appliance must not be supplied through an external
switching device, such as a timer.
WARNING: In order to avoid overheating, do not cover the air inlet or air
outlet – fire hazard!
Do not use the heater in small rooms (below 4 m
2
in size), in explosive
environnment, or for drying laundry.
Do not touch the front part of the appliance, it might reach hot tempera-
ture.
Use the heater only under supervision.
Do not insert any object and/or finger into the openings of the heater.
To extinguish burning appliances only use fire blankets.
Setting up / operation
Note: Make sure that there is always sufficient space between the appli-
ance and the wall or other large objects (> 50 cm). The air flow must not be
blocked by objects of any kind. If Paul is set up in a bathroom, keep a safety
intended normal operating position and they have been given super-
vision or instruction concerning use of the appliance in a safe way and
understand the hazards involved. Children aged from 3 years and less
than 8 years shall not plug in, regulate and clean the appliance or per-
form user maintenance.
If the supply cord is damaged, it must be replaced by the manufacturer,
or its service agent, or a qualified person in order to avoid a hazard.

Содержание

Похожие устройства

Скачать