Home
Главная
BEST
Вытяжка
Isasc 505
Инструкция по эксплуатации Страница: 3

BEST Isasc 505 [3/32] Operation

to terminal C; then replace wire clamp A and lid B on the wiring junction box; the other end of the wire is secured

to the terminal block on the outside control unit. Secure the box by means the 2 screws V (Fig. 13).

Make the electrical connection using the power supply cable.

Take the upper flue (the one with slots) and insert it into the telescopic structure, with the slots at the bottom; secure

it to the structure with 2 screws (Fig. 14).

Take the lower flue and insert it in the same way into the other flue; move it upwards and secure it with 4 screws (Fig.15).

Insert the control box in its seat and secure it by tightening the 2 screws inside the lower flue (Fig.16).

Refit the metallic surround removed prior to the installation procedure (Fig. 5).

Connect the halogen spot lights (Fig. 17).

Refit the grease filter.

Filtering Version:

Using the specific drilling template, make holes for fixing to the ceiling in the vertical part of your cooking top; observe

all indications for the final positioning of the appliance. Bear in mind that one of the two axes of the template must

correspond with the axis of the extractor hood controls.

Insert the baffle into the upper telescopic structure and secure it with 1 screw (Fig. 18). Connect a flex pipe, diameter

125 mm, securing it with a band (pipe and band not supplied).

Secure the upper part of the telescopic structure to the ceiling using the 4 screws and pads supplied (Fig. 7); pay close

attention since the positioning of the structure determines the final position of the extractor hood. During this operation,

insert the electricity supply cable through the specific hole in the structure (Fig. 7).

Fit the adapter flange B on the air output mouth of the motor (Fig. 19).

Fit the reducer R above the adapter flange (Fig. 19).

Secure the motor unit to the lower telescopic structure, using 4 nuts and 4 washers (Fig. 9). This block should then

be secured to the upper telescopic structure (Fig. 10) previously secured to the ceiling (with the 4 screws and 4 washers

removed previously).

Adjust the height of the telescopic structure using the four screws (Fig. 10) bearing in mind that the extractor hood

must be at minimum distance of 650 mm from the cooking top (Fig.11).

Through the apertures in the telescopic structure, secure the air evacuation pipe to the reducer using a band (Fig.20);

the tube and band are not supplied.

Make the electrical connection using the power supply cable.

Take the upper flue (the one with slots) and insert it into the telescopic structure, with the slots at the top; secure

it to the structure with 2 screws (Fig. 21).

Take the lower flue and insert it in the same way into the other tube; move it upwards and secure it with 4 screws (Fig.15).

Insert the control box in its seat and secure it by tightening the 2 screws inside the lower flue (Fig.16).

Refit the metallic surround removed prior to the installation procedure (Fig. 5).

Connect the halogen spot lights (Fig. 17).

Bear in mind that the Filtering Version requires a charcoal filter; verify whether this filter is already fitted and, if not,

install the filter: push the filter against the spring and twist it upwards (Fig. 22).

Refit the grease filter.

OPERATION

CONTROLS (Fig.23):

A) Turns the LIGHTS off

B) Turns the LIGHTS on.

C) Decreases speed down to minimum speed. If pressed for 2" the motor is turned off.

D) Activates the motor (calling the last speed used) and increases the speed until reaching maximum.

E) FILTER ALARM/TIMER RESET: when pressing the key during display of the filter alarm (motor off) it resets the hour

counter. When pressing the key when the motor is running, the TIMER is activated and the hood will automatically be switched

off after 5 minutes.

L1) The 4 green LEDs indicate the running speed.

L2) When the LED is red (motor off) it indicates the FILTER ALARM. When the LED is green (flashing) it indicates that

the TIMER has been activated with the key E.

FILTER ALARM:

After 30h of operation, the LED L2 turns RED. It indicates that the grease filters need to be cleaned.

After 120h of operation, the LED L2 turns RED and flashes; It indicates that the grease filters need to be cleaned and

the charcoal filters replaced. After cleaning the grease filters (and/or replacing the charcoal filters), restart the hour counter

(RESET) by pressing the key E during display of the filter alarm.

CONTROLS (Fig.24):

This appliance is equipped with a completely automatic system (Advanced Sensor Control) capable to manage

all the functions of your hood. Thanks to the ASC, the air in the kitchen is costantly clean and odour free

without any manual intervention. The advanced sensor catches all sort of vapours, smokes and odours caused

by the cooking process. The ASC also captures an abnormal presence of GAS. Moreover, this hood was

born of the Home Comfort project aimed at maximum noise reduction. It also has an Air Refresh function,

BEST Isasc 505 [3/32] Operation

Содержание

Похожие устройства