BEST Isaschc 505 [2/32] Installation
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

BEST Isaschc 505 [2/32] Installation

BEST Isasc 505 [2/32] Installation
ENGLISH
The appliance must be installed by a qualified person in compliance with the instructions provided.
Warning: Failure to install the screws or fixing device in accordance with these instructions may result in electrical hazards.
Only for hoods equipped with electronic control: the 4th speed (intensive) is automatically lowered to 3rd speed after
5 minutes of operation to optimise energy consumption.
- If the hood is left on (lights and/or motor), after 10 hours in the absence of commands from the user, it will automatically
switch to OFF condition with all services switched off. In hoods with voltage 120V/60Hz this function is not active.
- The Buzzer emits a “beep” each time that a command is set from the keyboard or remote control (optional).
- In the event of interruption of power during the hood, if you restore the hood in the OFF state, then the engine must
be reactivate manually.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons
in order to avoid a hazard.
DESCRIPTION
The unit can be found in filtering hoods, ducting hoods or in hoods with an outside motor. In the Filtering
version the air and the kitchen fumes that are conveyed by the apparatus are depurated by the charcoal filter
and put back into the room through the small grilles of the ventilation flue (Fig. 1). ATTENTION: When using the
filtering version, a charcoal filter and an air baffle (Fig. 1A) must be used, which placed at the top of the structure,
allows the air to recycle back into the room. The charcoal filters are not supplied. In the Ducting version, cooking
vapours and odours are conveyed straight outside by a disposal duct which passes through the ceiling (Fig. 2).
In the hoods with an external motor (Fig. 3), a vacuum suction unit must be connected; this exhaust will operate
separately, conveying the exhaust air through the unit. Only use vacuum units suggested in the original
catalogue.
INSTALLATION
ATTENTION: 3 persons are required for proper installation; the unit should be installed by a qualified operator.
Also follow carefully each step of the assembly instructions, and once installation has been completed, make sure
that the hood is firmly secured in place.
Before proceeding with assembly operations and to ensure easier manoeuvrability of the appliance, disengage
the grease filter: push the handle outwards and pull the filter downwards. 4).
Also remove the metallic surround by removing the 4 retaining screws (Fig. 5).
Separate the upper part of the telescopic structure from the lower part by removing the 4 retaining screws and
the 4 washers (Fig. 6).
For assembling it is essential to: – Prepare the connection to the mains within the telescopic flue. – If your unit is
installed in an ducting hood or in a hood with outside motor, prepare the air exhaust hole.
When installing ducting hoods and hoods with outside motor, to achieve the best possible conditions use an
air exhaust pipe that : is as short as possible, has a minimum of curves (maximum angle: 90°), is made of a
material that complies with the standards (which vary from nation to nation) and iv) is smooth on the inside. It
is also advisable to avoid any drastic changes in pipe section (diameter: 150 mm).
ASSEMBLY
Ducting version and version with an external motor:
Using the specific drilling template, make holes for fixing to the ceiling in the vertical part of your cooking top; observe
all indications for the final positioning of the appliance. Bear in mind that one of the two axes of the template must
correspond with the axis of the extractor hood controls.
Secure the upper part of the telescopic structure to the ceiling using the 4 screws and pads supplied (Fig. 7); pay close
attention since the positioning of the structure determines the final position of the extractor hood. During this operation,
pass the air air evacuation pipe inside the telescopic structure and the electricity supply through the specific hole
in the structure (Fig. 7).
Fit the adapter flange A on the air output mouth of the motor (Fig. 8) and fix the flange B (Fig. 8).
Secure the motor unit to the lower telescopic structure, using 4 nuts and 4 washers (Fig. 9). This block should then
be secured to the upper telescopic structure (Fig. 10) previously secured to the ceiling (with the 4 screws and 4 washers
removed previously). Adjust the height of the telescopic structure using the four screws (Fig. 10) bearing in mind that
the extractor hood must be at minimum distance of 650 mm from the cooking top. (Fig.11).
Through the apertures in the telescopic structure, secure the air evacuation pipe to the adapter flange using a band
(Fig.12); the pipe and band are not supplied.
Only for models with external motor (Fig. 13): plug the hood into the outside control unit using the special terminal
block: remove wire clamp A and lid B from the wiring junction box; secure the wire connecting the control unit

Содержание

Похожие устройства

Скачать