Home
Главная
BEST
Вытяжка
Phantom 90
Инструкция по эксплуатации Страница: 15

BEST Phantom 90 [15/56] English

English

! The appliance must be installed by a qualified

person in compliance with the instructions

provided.

Wear gloves when carrying out installation and

maintenance operations.

If the supply cord is damaged, it must be replaced by

the manufacturer, its service agent or similarly qualified

persons in order to avoid a hazard.

Warning: Failure to install the screws or fixing device in

accordance with these instructions may result in

electrical hazards.

AIR VENT

(for ducting versions)

! Prepare the hole and the air vent duct (150 mm

diameter).

! Use a duct of the minimum indispensible length.

! Use a duct with as few elbows as possible (maximum

elbow angle: 90°).

! Avoid drastic changes in the duct cross-section.

! Use a duct with an as smooth as possible inside.

! The duct must be made of certified material.

! Do not connect the hood to smoke exhaust ducts for

the products of combustion (boilers, fireplaces,

stoves, etc).

! For the air vents comply with the provisions laid down

by the competent authorities.

In addition, the air must not be evacuated through a

hole in the wall unless specifically intended for this

purpose.

! Fit air intakes in the room to prevent the hood from

creating a negative pressure in the room (which must

not exceed 0.04 mbar); if the hood is used at the

same time as non-electrical equipment (gas-, oil- and

charcoal-fired stoves, etc.) the exhaust gas may be

sucked in by the heat source.

FILTERING OR DUCTING VERSION ?

The hood may be in filtering or in ducting version.

Decide from the outset which type is to be installed.

For better efficiency, we recommend installing the hood

in the ducting version (if possible).

Ducting version

Versione with external motor

The hood purifies the air and evacuates it to the outside

through an exhaust duct (diameter 150 mm).

Filtering version

The hood purifies the air and recycles the clean air

back into the room.

Only for hoods equipped with electronic control:

The 4th speed (intensive) is automatically lowered to

3rd speed after 5 minutes of operation to optimise energy

consumption; in hoods with voltage 120V/60Hz this

function is not active and the 4th speed is indicated by

the letter b (Booster).

- If the hood is left on (lights and/or motor), after 10

hours in the absence of commands from the user, it will

automatically switch to OFF condition with all services

switched off. In hoods with voltage 120V/60Hz this

function is not active.

- The Buzzer emits a “beep” each time that a command

is set from the keyboard or remote control (optional).

- In the event of interruption of power during the hood,

if you restore the hood in the OFF state, then the

engine must be reactivate manually.

Only for hoods equipped with infrared sensor

controls: The unit is equipped with infrared sensor

controls that, if exposed to direct sunlight may not work

properly; use curtains or other devices to shield the

sunlight.

CONTROLS

Controls

Key A: light switch.

Key B: first speed motor ON/OFF switch.

Key C: second speed switch.

Key D: third speed switch.

Controls

Button TC1 (Lights): Switches main light ON/OFFWhen

the main light is on, BL1 changes colour and becomes

active.When the button is pressed for more than a

second, it switches the courtesy lights (optional) on/off.

Button TC2 (Motor-V1): Motor ON/OFF - Activates the

motor at 1st speed.

Button TC3 (Motor-V2)Activates the motor at 2nd

speed.

Button TC4 (Motor-V3)Activates the motor at 3rd speed.

Button TC5 (Motor-V4)Activates the motor at 4th

speedMaximum speed is timed at a maximum of 5

minutes, after which 3rd speed is set

automatically.When the motor is active, the LED of the

last selected button (TC2-TC5) active to signal which

speed has been set.

Button TC6 (TIMER auto power off 5 min.)Activates the

TIMER function at the speed that has already been

selectedIf the motor is NOT active, it switches on the

motor at the 1st speed and activates the TIMER

functionWhen the TIMER function is active, BL6

becomes active.

30h filter ALARM: after 30 hours of operation, an alarm

switches on to signal the need for anti-grease filter

cleaning.The filter alarm, when active, is displayed for

30 sec each time the motor is deactiva-ted:BL6 remains

TC1

TC2

TC3

TC4

TC5

TC6

Содержание

Похожие устройства

English The appliance must be installed by a qualified person in compliance with the instructions provided Wear gloves when carrying out installation and maintenance operations If the supply cord is damaged it must be replaced by the manufacturer its service agent or similarly qualified persons in order to avoid a hazard Warning Failure to install the screws or fixing device in accordance with these instructions may result in electrical hazards AIRVENT for ducting versions Prepare the hole and the air vent duct 150 mm diameter Use a duct of the minimum indispensible length Use a duct with as few elbows as possible maximum elbow angle 90 Avoid drastic changes in the duct cross section Use a duct with an as smooth as possible inside The duct must be made of certified material Do not connect the hood to smoke exhaust ducts for the products of combustion boilers fireplaces stoves etc For the air vents comply with the provisions laid down by the competent authorities In addition the air must not be evacuated through a hole in the wall unless specifically intended for this purpose At air intakes in the room to prevent the hood from creating a negative pressure in the room which must not exceed 0 04 mbar if the hood is used at the same time as non electrical equipment gas oil and charcoal fired stoves etc the exhaust gas may be sucked in by the heat source FILTERING OR DUCTING VERSION The hood may be in filtering or in ducting version Decide from the outset which type is to be installed For better efficiency we recommend installing the hood in the ducting version if possible Ducting version Versione with external motor The hood purifies the air and evacuates it to the outside through an exhaust duct diameter 150 mm version The hood purifies the air and recycles the clean air back into the room Only for hoods equipped with electronic control The 4th speed intensive is automatically lowered to 3rd speed after 5 minutes of operation to optimise energy consumption in hoods with voltage 120V 60Hz this function is not active and the 4th speed is indicated by the letter b Booster If the hood is left on lights and or motor after 10 hours in the absence of commands from the user it will automatically switch to OFF condition with all services switched off In hoods with voltage 120V 60Hz this function is not active The Buzzer emits a beep each time that a command is set from the keyboard or remote control optional In the event of interruption of power during the hood if you restore the hood in the OFF state then the engine must be reactivate manually Only for hoods equipped with infrared sensor controls The unit is equipped with infrared sensor controls that if exposed to direct sunlight may not work properly use curtains or other devices to shield the sunlight CONTROLS ABCD Controls Key A light switch Key B first speed motor ON OFF switch Key C second speed switch Button TC1 Lights Switches main light ON OFFWhen the main light is on BL1 changes colour and becomes active When the button is pressed for more than a second it switches the courtesy lights optional on off Button TC2 Motor V1 Motor ON OFF Activates the motor at 1st speed Button TC3 Motor V2 Activates the motor at 2nd speed Button TC4 Motor V3 Activates the motor at 3rd speed Button TC5 Motor V4 Activates the motor at 4th speedMaximum speed is timed at a maximum of 5 minutes after which 3rd speed is set automatically When the motor is active the LED of the last selected button TC2 TC5 active to signal which speed has been set Button TC6 TIMER auto power off 5 min Activates the TIMER function at the speed that has already been selectedlf the motor is NOT active it switches on the motor at the 1st speed and activates the TIMER functionWhen the TIMER function is active BL6 becomes active 30h filter ALARM after 30 hours of operation an alarm switches on to signal the need for anti grease filter cleaning The filter alarm when active is displayed for 30 sec each time the motor is deactiva ted BL6 remains

Скачать