APC PRM24 для шасси Инструкция по эксплуатации онлайн
ProtectNet
®
Modular Data Line
Installation Manual
Surge Protection System
Thank you for purchasing APC’s Modular Data Line Surge Protection System. Please fill out the supplied Warranty Registration Card or an on-line Product Warranty Registration form at www.apc.com.
APC’s Modular Data Line Surge Protection System consists of a variety of interchangeable surge suppression modules installed in either a four position “PRM4” or a 24 position “PRM24” chassis with the mounting hardware and ground wire. A list
of the modules that are available, and the types of data lines they protect are provided below. The PRM4 is designed to mount inside a home wiring enclosure. The PRM24 is designed to mount in a standard 19-inch rack enclosure.
This manual provides basic installation information for the PRM4 chassis and associated modules. For PRM24 installation information, reference APC manual 990-1383A.
Note: Procedures provided in this document are not intended to supersede local standards or codes. Reference the Telecommunications Industries Association and Electronic Industries Alliance publication “Commercial Building,
Telecommunications Cabling Standard, General Requirements” (document number TIA/EIA-568-B.1-2001) to ensure the system wiring is installed properly.
Safety
Please read and save these instructions, and observe the following safety precautions.
• Use the system in a protected environment only.
• Never install telephone wiring or coaxial cable during a lightning storm.
• Follow the installation instructions carefully. The current limiting feature of this product could be rendered inoperable if the product is improperly installed.
Caution: This equipment is intended to be used in a restricted access area and should only be worked on by qualified service personal.
w
w
w
.apc.com
®
Other Considerations
• Do not install this device in an environment where the operating temperature exceeds 0 to 40
o
C (32 to 104
o
F).
• Do not install this device where the relative humidity exceeds 95%, non-condensing.
• Do not store this device in an environment that exceeds 0 to 45
o
C (32 to 113
o
F).
Chassis Installation and Grounding
APC recommends that the ProtectNet Data Line Surge Protection chassis ( , Figure 1) PRM24, be installed using the mounting hardware provided with the chassis.
Additionally, the chassis must be connected to a proper protective earth ground. A ground stud is provided on the back of the chassis. Ensure the mounting rack or
enclosure is connected to a proper ground. Install the chassis and modules as shown in Figure 1.
Module Installation
The system chassis is designed to accomodate up to 24 data line modules.To install a module, remove one of the blank panels by pulling it straight out from the
chassis.Align the module with the groove in the chassis, and slide the module fully into the chassis.
Cable Installation
To install a data line cable , connect the input RJ-45 connector to the signal source and then to the upper connector on the module. Connect a data line cable from the
lower connector on the module to the equipment to be protected.
Note: To accomodate 24 modules, the four-wide center blank panel must be removed.
1
2
3
4
5
6 7 8
9
Module Information
Model PNETR5 and PNETR6 (Cat5 and Cat6 Network Protection)
The PNETR5 and PNETR6 modules protect the ports of a
network interface cards, hubs or other local area network (LAN) equipment from damage caused by electrical tran-
sients over a Cat5 or Cat6 data line. These modules provide surge protection for 10Base-T, 100Base-T4, 100Base-TX, 100VG or Token Ring Type 3 UTP port (RJ-45), and
VOIP standards and applications. Both modules comply with IEEE 802.3 and IEEE 802.5. PNETR6 is also compatible with 1000Base-T/Cat6 and IEEE 802.12 Ethernet
standard, Cat5 and Cat6. PNETR5 and PNETR6 key specifications are listed below.
Item Specification
PNETR5/PNETR6 Lines Protected
Pins 1 - 8 on RJ-45 connector
PNETR5/
PNETR6 Mode of Protection
Between send/receive pairs and any signal line to ground.
PNETR5/
PNETR6 Peak Voltage
± 2,000 Volts, 1.2/ 50 µs test waveform
PNETR5 Peak Current 150 Amps, 8/20 µs test waveform
PNETR6 Peak Current 250 Amps, 8/20 µs test waveform
PNETR5 Breakover (turn on) Voltage 60 V peak nominal between send/receive pairs
PNETR6 Breakover (turn on) Voltage 60 Vdc nominal
PNETR5/
PNETR6 Isolation
Both comply with applicable safety isolation requirements of IEEE 802.3 and 802.5.
PNETR6 complies with 802.12 Ethernet Cat5, 6.
PNETR5/
PNETR6 Response Time
<1ns
Agency Approvals UL 497B recognized
6
3
4
8
To Equipment
to be Protected
From Signal
Source
1
7
5
2
9
Figure 1. Typical Installation
Ground
Stud / Wire
General Information
Содержание
- Apc com 1
- Installation manual 1
- Modular data line 1
- Protectne 1
- Surge protection system 1
- American power conversion 1 401 789 5735 or 1 800 800 4apc 4272 132 fairgrounds road http www apc com support or west kingston ri 01892 usa esupport apcc com 2
- Apc warrants its products to be free from defects in materials and workmanship under normal use and service for the lifetime of the original purchaser its obligation under this warranty is limited to repairing or replacing at its sole option any such defective products to obtain service under warranty you must obtain a returned material authorization rma number from apc or an apc service center product must be returned to apc or an apc service center with transportation charges pre paid and must be accompanied by a brief description of the problem and proof of date place of purchase this warranty applies only to the original purchaser 2
- As a secondary protector 2
- Customer service technical support 2
- Eia tia 568 category or cable type frequency mhz attenuation db 100m equivalent cable length m 2
- F the device arrived damaged notify the carrier immediately 2
- Federal communications commission fcc notice 2
- For information please call the apc customer service center at 2
- Go to http www apc com support 2 have the model number serial number and date of purchase available be prepared to troubleshoot the problem with an apc technical support representative if this is not successful apc will issue a return merchandise authorization rma number and a shipping address 2
- If the device requires service do not return it to the dealer the following steps should be taken 2
- Item specification 2
- Limited lifetime warranty 2
- Model p232r rs232 protection 2
- Model pdigtr digital telephone protection 2
- Model pnetr5 in applications where the network data transmission rate is high and cable lengths are long insertion loss introduced by in line devices is a major consideration at the 100 mbp s data transmission rate there is a small insertion loss introduced by the pnetr5 use table 1 below to approximate the insertion loss introduced by the pnetr5 based on your installed cable type the iso iec 8802 3 standard specifies a maximum utp cable length of 150 meters per segment at 10 and 100 mbp s for thinnet maximum cable length is 185 meters 607 ft 2
- Model pnetr6 applications where the network data transmission rate is high and cable lengths are long an insertion loss is introduced by in line devices at 250 mbp s there is a small insertion loss introduced by the pnetr6 use table 1 below to approximate the insertion loss based on the installed cable type the iso iec 8802 3 standard specifies a 150 meter maximum utp cable length per segment at 250 mbp s 2
- Model ptel2r analog telephone protection 2
- Model pvr digital cable protection 2
- Module information continued 2
- Service 2
- Table 1 2
- The p232r module is used for rs232 communications rs232 multiports asynchronous multiplexers asynchronous printer spoolers using unshielded twisted pair wiring with rj 45 connectors it protects up to four ports per unit 2
- The pdigtr module is only designed to be used in t1 csu dsu isdn dds and digital leased line telecommunication equipment and tnv 1 or selv circuits insertion loss introduced by in line devices is a major consideration 2
- The ptel2r module protects analog devices including telephones adsl isdn2 voice mail automated answering systems fax machines and modems from damage caused by lightning generated electrical transients each ptel2r module protects up to 2 lines 2
- The pvr module provides digital cable protection for video cable modem equipment against surges and spikes caused by lightning and electrostatic discharge esd it is compatible with cable television catv a digital satellite system dss television video cassette recorder vcr cable modem and tv antenna equipment it is also compatible with many dss units that have operating voltages below 26 volts dc the pvr is recognized by underwriter s laboratories u 2
Похожие устройства
- APC SURT192RMXLBP Инструкция по эксплуатации
- APC RM 192V Battery Pack SRT192RMBP2 Инструкция по эксплуатации
- APC RM 192V Battery Pack SRT192RMBP Инструкция по эксплуатации
- Stadler Form O-060 Инструкция по эксплуатации
- Elikor H1M-GA Инструкция по эксплуатации
- Tefal HD 5115 Инструкция по эксплуатации
- Babyliss E960Е Инструкция по эксплуатации
- Moulinex ME 456139 Инструкция по эксплуатации
- Gorenje EC52203AW0 Белый Инструкция по эксплуатации
- Moulinex Fresh Express + DJ755G Инструкция по эксплуатации
- Tefal Effectis GV6731 Белый, розовый Инструкция по эксплуатации
- Moulinex HV8 ME 660832 Инструкция по эксплуатации
- Gorenje K17TRE Инструкция по эксплуатации
- Gorenje E52102AW0 Белый Инструкция по эксплуатации
- APC SRT72BP Инструкция по эксплуатации
- Gorenje EC52203AS0 Cеребристый Инструкция по эксплуатации
- Babyliss AS101E Инструкция по эксплуатации
- Gorenje NRK6191GW White Инструкция по эксплуатации
- Gorenje RK6191AX Серебристый Инструкция по эксплуатации
- Gorenje RK6201FX Серебристый Инструкция по эксплуатации