Home
Главная
Timberk
Воздухоочиститель
Cloud TAP FL150 SF (BL)
Инструкция по эксплуатации Страница: 5

Timberk Cloud TAP FL150 SF (BL) [5/24] Operation of the instrument

Timberk Cloud TAP FL150 SF (W) [5/24] Operation of the instrument

www.timberk.com • electric air purifier

Power Control – To operate the TAP FL150 SF air purifier, press the ON/OFF

button to turn on the air purifier. Press the button again to turn the unit off.

Timer Control – The TAP FL150 SF air purifier can be programmed to turn off

after a preset amount of time. Press the «TIMER» button to program the timer.

Each press will add one hour up to a total of 24 hours. Keeping the button

pressed will automatically increase to 24 hours, 1 hour at a time, after that it

will turn back to off.

Fan Speed Control – The TAP FL150 SF has three different speeds of

cleaning, LOW, MED and HI. Press «SPEED» button to cycle the settings and

select the fan speed you desire. The speed state will be shown on the LED

display.

Clean Filter Indicator Light – The TAP FL150 SF Clean Filter Indicator Light

will turn on each time the filter needs to be cleaned. To reset the filter indicator,

press the TIMER and the ON/OFF buttons together for 3 seconds. The

CLEAN FILTER light will flash 3 times and then turn off completely, indicating

the unit has been reset.

Night Mode – If the UV light bar is too bright, press the «Night Mode» button

to turn off the UV light bar feature, and the lighted display. The ON/OFF

indicator, however, will remain lit. The night mode only turns off UV light bar not

the actual UV feature.

Reset Filter Control – Press down the «TIMER» and «ON/OFF» button for 3

seconds, the clean filter light will flash 3 times and then the clean filter light will

turn off, indicating the unit has been reset.

UV Control – Press the UV/VOC control button «UV/VOC» to turn on the UV

lamp to kill harmful airborne germs and reduce harmful VOC (volatile organic

compounds). Press it again to turn off the UV and VOC.

7. OPERATION OF THE INSTRUMENT

NOTE:

Always make sure the TAP FL150 SF is turned off and

unplugged before cleaning.

•Vacuuming will restore performance of the permanent

HEPA-type filter. However, the filter may appear stained.

This is normal and does not affect performance in any

way.

• Do not use water or any household cleaners or

detergents to clean the permanent HEPA-type filter.

• The inlet grill may be cleaned (after unit is turned off

and unplugged) with a vacuum or a slightly damp cloth.

1 2 3 4

Keep the TAP FL150 SF functioning properly by cleaning the permanent

HEPA-type filter every four weeks. More frequent cleaning will be necessary

if the unit is located in an area with a high level of airborne contaminants

(excessive amounts of smoke, pet dander, etc.).

8. CLEANING AND MAINTENANCE INSTRUMENT

Cleaning the permanent HEPA-type filter.

1. Release the inlet grill by pressing on the locking latch (see diagram of

Main Parts).

2. Remove the inlet grill from the unit as shown below.

3. Grasp the left and right frames of the permanent HEPA-type filter through

the indentations on the sides of the filter enclosure and remove the filter.

4. To clean the permanent HEPA-type filter, use the brush or crevice

attachment with a vacuum cleaner. Run the attachment along the inlet and

outlet side of the filter, cleaning between the crevices as much as possible.

Do not use water or any household cleaners or detergents to clean the

permanent HEPA-type filter.

5. Once the permanent HEPA-type filter has been cleaned and checked

for any possible damage, replace the filter back in the reverse direction

described here. Plug in the unit and hold down Timer + Power On button

for 3 seconds. The clean filter light will go off and your cleaning maintenance

Timberk Cloud TAP FL150 SF (BL) [5/24] Operation of the instrument

Содержание

Похожие устройства