Delonghi KT-T 60 BF [8/44] Use and maintenance
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Delonghi KT-T 60 BF [8/44] Use and maintenance

Delonghi KT-T 60 BF [8/44] Use and maintenance
- 8 -
Before this operation, perform the following steps
dependingonthemodelpurchased:
MODEL 1
Removethe3panelsAasshowninFig.4.
PullhandleBasshowninFig.6.
MODEL 2
OpenpanelCasshowninFig.5.
Pullhandle BasshowninFig.6.
Iftheappliancehasalid,removeitbyremovingthe4
screwsBasshowninFig.9A.
• WALL FIXING
Markthepositionofthelowersideofthehoodonthewall
(Fig.2A).Maintaintheminimumdistancerequiredfromthe
hobasshowninFig.2B.
-Position the xing templateon the wall, making sure
thatthelinecoincideswiththelinepreviouslymadeon
thewall.
- Markthe xingholes and cut theminto thematerial
(Fig.3).
-Fixthe2topscrewsKandscrewanchors(Fig.3),without
tighteningthemcompletely.
-Placetheapplianceagainstthewall,alignitinhorizontal
positionandtightenscrewsK(Fig.7).
-Oncetheadjustmenthasbeencompleted,xthehood
usingthe2 screwsC(Fig.8).
-Whencarryingoutthexingoperations,useonlyscrews
andscrewanchorssuitedtothetypeofwall(e.g.reinforced
concrete,plasterboardetc.).
-Ifthescrewsandscrewanchorsaresuppliedwiththe
appliance,makesurethattheyaresuitedtothetypeof
walltowhichthehoodmustbexed.
• INSTALLATION OF MODELS WITHOUT DECORATIVE
DUCTS
EXTRACTOR HOOD
-Removethe4screwsBasshownin(Fig.9A).
-RemovebothgridEontheairoutletholeandlidMas
shownin(Fig.9B).
-Connectthehoodtotheexible hose (not supplied)
andthehosetotheairexhaustholepreviouslyprepared
(Fig.9C).
-Fixthelidonceagainbyusingthe4screwspreviously
removedin(Fig.9A).
• OPTIONAL ACCESSORIES
This model may have decorative ducts as optional
accessories-askyourretailerforinformation.
Beforexing the decorativeducts,removeboth the 4
screwsB andlidM,asshownin(Fig.10A-B).
Asound-absorbingkitisalsoavailable(tobeorderedasan
OPTIONALaccessory)inordertoincreasethequietness
levelof the hood.The sound-absorbing layer mustbe
appliedto theback of the decorativepanel.For xing
operations,refertotheinstructionssuppliedwiththekit.
• INSTALLATION OF MODELS WITH DECORATIVE
DUCTS
Make sure the electrical power supply is within the
measurementsofthedecorativeconnector.
Adjustthewidthofthesupportbracketofthetopconnector
(Fig.11C).Thenxittotheceilingsothatitisonthesame
axisasthehoodusingscrewsA(Fig.11C)adheringto
thedistancefromtheceilingshownin(Fig.11B).Connect
angeC to the air exhausthole using exiblehose L
(Fig.11D).
Slidethetopductintothebottomduct.Fixthebottomduct
tothehoodusingscrewsB(supplied)(Fig.11E).
Pulloutthetopductasfarasthebracketandxitusing
screws F(Fig.11C).
• FILTER HOOD
Please note:
Theltersshouldbeorderedasaccessoriesfromyour
retailer.
Weoffer 2 differenttypes of kitwhich canbeused to
transformtheEXTRACTORhoodintoaFILTERhood,in
accordancewiththetypeofappliancemodelpurchased.
Onekitcontainsextractablelters(g.10)andtheother
containscircularlters(g.15).
1-Ifyoundabracket(suchastheoneindicateding.
14)includedintheproductpackaging,thisshouldbexed
tothehoodusingthe6screwssupplied.
Toreplacetheactivecarbonlterspulllever Boutwards
asshownin(Fig.10).
2-Ifyourproductisnotsuppliedwithabracket,thismeans
thattheactivecarbonlterisacircularversion(g.15).
Theltersshouldbettedtotheextractionassemblyinside
thehood,bycentringthemandrotatingthem90degrees,
untiltheyclickintoplace(Fig.15).
USE AND MAINTENANCE
• It is recommended tooperatethe appliance prior to
cooking.
It is recommendedtoleavethe appliance inoperation
for 15 minutes after cooking is terminated in order to
completelyeliminatecookingvapoursandodours.
Theproperfunctionofthecookerhoodisconditionedby
theregularityofthemaintenanceoperations,inparticular,
theactivecarbonlter.
•The anti-grease lters capture the grease particles
suspendedintheair,andarethereforesubjecttoclogging
accordingtothefrequencyoftheuseoftheappliance.
Inorder to preventrehazard, it is recommendableto
cleanthelteratamaximumof2monthsbycarryingout
thefollowinginstructions:
- Remove the lters from the cooker hood and wash
theminasolutionofwaterandneutralliquiddetergent,
leavingtosoak.
-Rinsethoroughlywithwarmwaterandleavetodry.
-Theltersmayalsobewashedinthedishwasher.
Thealuminium panelsmayalterin colourafter several
washes.Thisis not cause for customer complaint nor
replacementofpanels.
•Theactivecarbonlterspurifytheairthatisreplaced
intheenvironment.Thelters are not washablenor
re-useable and must be replaced at maximum every
four months.The saturation of the active carbon lter
depends on the frequencyof use of the appliance,by
the type of cooking and the regularity of cleaning the
anti-greaselters.

Содержание

Похожие устройства

Скачать
Случайные обсуждения

Ответы 0

Как заменить предохранитель
4 года назад