Home
Главная
Vitek
Кухонные Комбайны
VT-1608
Инструкция по эксплуатации Страница: 6

Vitek VT-1608 [6/48] English

ENGLISH

– Install the lid (8) on the processing bowl

(4), matching the extreme left mark

the lid (8) and the mark

on the motor unit

(2), then turn the lid clockwise until fixing,

so that the mark

on the lid matches the

symbol

(CLOSE) (pic. 6).

– Install the food tray (10) on the lid (8).

USING THE SLOW JUICER

Important! Before switching the unit on,

make sure that all parts are installed prop-

erly. Do not switch the unit on without

food.

Fruit, vegetables and berries intended for

processing must be fresh.

– Before juice extracting remove inedible

parts from vegetables or fruits, such as

stems, hard peel or stones, for example,

cherry or peach stones.

– Wash fruit/vegetables and cut them into

pieces matching the feeding chute (9).

– Place unit on a flat stable surface.

– Place the juice cup (12) under the pro-

cessing bowl (4) spout (pic. 7).

– Insert the power plug into the socket.

– Switch the slow juicer on by setting the

switch (3) to the «I» position.

Operation mode switch (3) position

«I» - the juicer is on.

«O»– the juicer is off.

«R» means change of the screw rotation

direction. The Reverse mode is used only

when the screw (7) is blocked. The screw

can be blocked if the unit is overloaded

with products (due to processing of hard or

fibrous fruits or vegetables). To switch the

reverse mode turn the unit off setting the

switch (3) to the position «O», then press and

hold the switch (3) in the position «R». Use

this operation mode for 3-5 seconds. If the

problem still remains, disassemble the juicer,

clean and then assemble it .

If the screw is blocked again, you should

cut fruits and vegetables into smaller

pieces and feed products slower.

Note: The unit will be switched on only if all

the removable parts are installed properly,

and the lid (8) is in the position

(CLOSE).

– Feed fruit or vegetables into the feed-

ing chute (9), only when the screw (7) is

rotating.

– Put the precut vegetables or fruits into the

feeding chute (9) gradually and push them

slightly with the pusher (11). Do not press

on the pusher hardly as it can decrease the

amount of extracted juice and even stop

the screw (7) rotation. The slower is the

fruit and vegetables processing, the higher

is the juice extraction rate.

– Do not put your fingers or any other foreign

objects into the feeding chute (9).

– Periodically check the mesh filter (6) for

obstruction while operation and wash

the mesh filter (6), if necessary. Before

removing the filter switch the unit off and

unplug it.

– Control the pulp container (1) filling, if

the container is full, switch the juicer off,

unplug it and remove the pulp from the

container (1), then install the container (1)

back to its place.

Attention! The maximal continuous operation

time of the juicer is approximately 30 minutes

with a 10-15 minute subsequent break.

After processing of 1 kg hard and fibrous fruits

and vegetables (citrus plants, pineapples

etc.) disassemble and clean the unit. Non-

compliance with the requirement can cause

the screw blockage and will complicate the

unit cleaning.

Self-cleaning function

If you need to clean the unit before extract-

ing juice from another type of vegetables

or fruit, use the self-clean function.

– Switch the unit on and pour a glass of

water into the feeding chute (9). Most pulp

will be removed.

– Switch the unit off and clean the pulp con-

tainer (1) and the juice cup (12).

VT-1608_IM.indd 6 30.05.2013 14:44:32

Vitek VT-1608 [6/48] English

Содержание

Похожие устройства