Ryobi RAG800-115G Angle grinder 800W IN2 5133002518 [4/24] Angle grinder safety warnings

Ryobi RAG750-115G Angle grinder IN2 5133002489 [4/24] Angle grinder safety warnings

maintained cutting tools with sharp cutting edges

DUHOHVVOLNHO\WRELQGDQGDUHHDVLHUWRFRQWURO

g) Use the power tool, accessories and tool bits

etc, in accordance with these instructions,

taking into account the working conditions and

the work to be performed. Use of the power tool

for operations different from those intended could

result in a hazardous situation.

SERVICE

Have your power tool serviced by a qualified repair

person using only identical replacement parts. This will

ensure that the safety of the power tool is maintained.

ANGLE GRINDER SAFETY WARNINGS

SAFETY WARNINGS COMMON FOR GRINDING OR

ABRASIVE CUTTING-OFF OPERATIONS:

a) This power tool is intended to function as a

grinder or cut-off tool. Read all safety warnings,

instructions, illustrations and specifications

provided with this power tool. Failure to follow

all instructions listed below may result in electric

VKRFNILUHDQGRUVHULRXVLQMXU\

b) Operations such as sanding, wire brushing

or polishing are not recommended to be

performed with this power tool. Operations for

which the power tool was not designed may create

DKD]DUGDQGFDXVHSHUVRQDOLQMXU\

c) Do not use accessories which are not

specifically designed and recommended by the

tool manufacturer. Just because the accessory

can be attached to your power tool does not assure

safe operation.

d) The rated speed of the accessory must be at

least equal to the maximum speed marked on

the power tool. Accessories running faster than

WKHLUUDWHGVSHHGFDQEUHDNDQGIO\DSDUW

e) The outside diameter and the thickness of your

accessory must be within the capacity rating

of your power tool. Incorrectly sized accessories

cannot be adequately guarded or controlled.

f) Threaded mounting of accessories must match

the grinder spindle thread. For accessories

mounted by flanges, the arbour hole of the

accessory must fit the locating diameter of

the flange. Accessories that to do not match the

mounting hardware of the power tool will run out of

EDODQFH YLEUDWH H[FHVVLYHO\ DQG PD\FDXVHORVV

of control.

g) Do not use a damaged accessory. Before each

use inspect the accessory such as abrasive

wheels for chips and cracks, backing pad

for cracks, tear or excess wear, wire brush

for loose or cracked wires. If power tool or

accessory is dropped, inspect for damage

or install an undamaged accessory. After

inspecting and installing an accessory,

position yourself and bystanders away from

the plane of the rotating accessory and run the

power tool at maximum no-load speed for one

minute.'DPDJHGDFFHVVRULHVZLOOQRUPDOO\EUHDN

apart during this test time.

h) Wear personal protective equipment.

Depending on application, use face

shield, safety goggles or safety glasses.

As appropriate, wear dust mask, hearing

protectors, gloves and workshop apron

capable of stopping small abrasive or

workpiece fragments. The eye protection must

be capable of stopping flying debris generated by

YDULRXV RSHUDWLRQV 7KH GXVW PDVN RU UHVSLUDWRU

must be capable of filtrating particles generated

E\ \RXU RSHUDWLRQ 3URORQJHG H[SRVXUH WR KLJK

intensity noise may cause hearing loss.

i) Keep bystanders a safe distance away from

work area. Anyone entering the work area must

wear personal protective equipment. Fragments

RI ZRUNSLHFH RU RI D EURNHQ DFFHVVRU\ PD\ IO\

DZD\DQGFDXVHLQMXU\EH\RQGLPPHGLDWHDUHDRI

operation.

M Hold the power tool by insulated gripping

surfaces only, when performing an operation

where the cutting accessory may contact

hidden wiring or its own cord. Cutting accessory

FRQWDFWLQJD³OLYH´ ZLUHPD\PDNHH[SRVHGPHWDO

parts of the power tool “live” and could give the

RSHUDWRUDQHOHFWULFVKRFN

N Position the cord clear of the spinning

accessory. If you lose control, the cord may be cut

or snagged and your hand or arm may be pulled

into the spinning accessory.

l) Never lay the power tool down until the

accessory has come to a complete stop. The

spinning accessory may grab the surface and pull

the power tool out of your control.

m) Do not run the power tool while carrying it at

your side. Accidental contact with the spinning

accessory could snag your clothing, pulling the

accessory into your body.

n) Regularly clean the power tool’s air vents. The

motor’s fan will draw the dust inside the housing

DQG H[FHVVLYH DFFXPXODWLRQ RI SRZGHUHG PHWDO

may cause electrical hazards.

o) Do not operate the power tool near flammable

materials.6SDUNVFRXOGLJQLWHWKHVHPDWHULDOV

p) Do not use accessories that require liquid

coolants. Using water or other liquid coolants may

UHVXOWLQHOHFWURFXWLRQRUVKRFN

FURTHER SAFETY INSTRUCTIONS FOR ALL

OPERATIONS

Kickback and related warnings

.LFNEDFN LV D VXGGHQ UHDFWLRQ WR D SLQFKHG RU VQDJJHG

URWDWLQJZKHHOEDFNLQJSDGEUXVKRUDQ\RWKHUDFFHVVRU\

Pinching or snagging causes rapid stalling of the rotating

accessory, which in turn causes the uncontrolled power

tool to be forced in the direction opposite of the accessory’s

rotation at the point of the binding.

)RUH[DPSOHLIDQ DEUDVLYHZKHHOLVVQDJJHG RUSLQFKHG

E\ WKH ZRUNSLHFH WKH HGJH RI WKH ZKHHO WKDW LV HQWHULQJ

into the pinch point can dig into the surface of the material

FDXVLQJWKHZKHHOWRFOLPERXWRUNLFNRXW7KHZKHHOPD\

HLWKHUMXPSWRZDUGRU DZD\IURP WKHRSHUDWRUGHSHQGLQJ

on the direction of the wheel’s movement at the point of

SLQFKLQJ $EUDVLYH ZKHHOV PD\ DOVR EUHDN XQGHU WKHVH

conditions.

.LFNEDFNLVWKHUHVXOWRISRZHUWRROPLVXVHDQGRULQFRUUHFW

operating procedures or conditions and can be avoided by

WDNLQJSURSHUSUHFDXWLRQVDVJLYHQEHORZ

a) Maintain a firm grip on the power tool and

Ryobi RAG800-115G Angle grinder 800W IN2 5133002518 [4/24] Angle grinder safety warnings

Содержание

Похожие устройства