Hitachi CG47EYNK Инструкция по эксплуатации онлайн [12/86] 309352
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Hitachi CG47EYNK Инструкция по эксплуатации онлайн [12/86] 309352

Hitachi CG47EYNK Инструкция по эксплуатации онлайн [12/86] 309352
'"
"LADE&IG
7!2.).'
7EARPROTECTIVEGLOVESWHENHANDLINGORPERFORMING
MAINTENANCEONTHEBLADE
o5SEASHARPBLADE!DULLBLADEISMORELIKELYTOSNAGANDTHRUST
2EPLACETHEFASTENINGNUTIFITISDAMAGEDANDHARDTOTIGHTEN
o7HENREPLACINGBLADEPURCHASEONERECOMMENDEDBY()4!#()
WITHAMMONEINCHüTTINGHOLE
o7HENINSTALLINGSAWBLADEALWAYSFACETHESTAMPEDSIDEUP
)NTHECASEOFATOOTHBLADEITCANBEUSEDONEITHERSIDE
o5SECORRECTBLADEFORTHETYPEOFWORK
o7HENREPLACINGBLADEUSEAPPROPRIATETOOLS
o7HENCUTTINGEDGESBECOMEDULLRESHARPENORüLEASSHOWNIN
üGURE)NCORRECTSHARPENINGMAYCAUSEEXCESSIVEVIBRATION
o$ISCARDBLADESTHATAREBENTWARPEDCRACKED
BROKENORDAMAGEDINANYWAY
./4%
7HENSHARPENINGBLADEITISIMPORTANTTOMAINTAINANORIGINALSHAPE
OFRADIUSATTHEBASEOFTHETOOTHTOAVOIDCRACKING
-AINTENANCESCHEDULE
"ELOWYOUWILLüNDSOMEGENERALMAINTENANCEINSTRUCTIONS&OR
FURTHERINFORMATIONPLEASECONTACT()4!#()DEALER
$AILYMAINTENANCE
o#LEANTHEEXTERIOROFTHEUNIT
o#HECKTHATTHEHARNESSISUNDAMAGED
o#HECKTHEBLADEGUARDFORDAMAGEORCRACKS#HANGETHEGUARD
INCASEOFIMPACTSORCRACKS
o#HECKTHATTHECUTTINGATTACHMENTISPROPERLYCENTREDSHARPAND
WITHOUTCRACKS!NOFFCENTREDCUTTINGATTACHMENTINDUCESHEAVY
VIBRATIONSTHATMAYDAMAGETHEUNIT
o#HECKTHATTHECUTTINGATTACHMENTNUTISSUFüCIENTLYTIGHTENED
o-AKESURETHATTHEBLADETRANSPORTGUARDISUNDAMAGEDANDTHAT
ITCANBESECURELYüTTED
o#HECKTHATNUTSANDSCREWSARESUFüCIENTLYTIGHTENED
7EEKLYMAINTENANCE
o#HECKTHESTARTERESPECIALLYCORD
o#LEANTHEEXTERIOROFTHESPARKPLUG
o2EMOVETHESPARKPLUGANDCHECKTHEELECTRODEGAP!DJUSTIT
TOMMORCHANGETHESPARKPLUG
o#HECKTHATTHEAIRINTAKEATTHESTARTERISNOTCLOGGED
o#HECKTHATTHEANGLEGEARISüLLEDWITHGREASEUPTO
o#LEANTHEAIRüLTER
-ONTHLYMAINTENANCE
o2INSETHEFUELTANKWITHGASOLINEANDCLEANFUELüLTER
o#LEANTHEEXTERIOROFTHECARBURETORANDTHESPACEAROUNDIT
1UARTERLYMAINTENANCE
o#LEANTHECOOLINGüNSONTHECYLINDER
o#LEANTHEFANANDTHESPACEAROUNDIT
o#LEANTHEMUFČEROFCARBON
#!54)/.
#LEANINGOFCYLINDERüNSFANANDMUFČERSHALLBEDONEBYA
()4!#()!UTHORIZED3ERVICE#ENTER

Содержание

Похожие устройства

Blade Fig 30 Quarterly maintenance Clean the cooling fins on the cylinder WARNING Clean the fan and the space around it Wear protective gloves when handling or performing Clean the muffler of carbon maintenance on the blade CAUTION Cleaning of cylinder fins fan and muffler shall be done by a Use a sharp blade A dull blade is more likely to snag and thrust Replace the fastening nut if it is damaged and hard to tighten When replacing blade purchase one recommended by HITACHI with a 25 4mm one inch fitting hole When installing saw blade 2 always face the stamped side up In the case of a 4 tooth blade 1 it can be used on either side Use correct blade for the type of work When replacing blade use appropriate tools When cutting edges become dull re sharpen or file as shown in figure Incorrect sharpening may cause excessive vibration Discard blades that are bent warped cracked broken or damaged in any way NOTE When sharpening blade it is important to maintain an original shape of radius at the base of the tooth to avoid cracking Maintenance schedule Below you will find some general maintenance instructions For further information please contact HITACHI dealer Daily maintenance Clean the exterior of the unit Check that the harness is undamaged Check the blade guard for damage or cracks Change the guard in case of impacts or cracks Check that the cutting attachment is properly centred sharp and without cracks An off centred cutting attachment induces heavy vibrations that may damage the unit Check that the cutting attachment nut is sufficiently tightened Make sure that the blade transport guard is undamaged and that it can be securely fitted Check that nuts and screws are sufficiently tightened Weekly maintenance Check the starter especially cord Clean the exterior of the spark plug Remove the spark plug and check the electrode gap Adjust it to 0 6 mm or change the spark plug Check that the air intake at the starter is not clogged Check that the angle gear is filled with grease up to 3 4 Clean the air filter Monthly maintenance Rinse the fuel tank with gasoline and clean fuel filter Clean the exterior of the carburetor and the space around it GB 8 HITACHI Authorized Service Center

Скачать