Vitek VT-8120 [5/32] English
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Vitek VT-8120 [5/32] English

Vitek VT-8120 [5/32] English
5
E N G L I S H
Note: - provide that the HEPA filter (19) is always
clean, because the overall performance of the
vacuum cleaner depends on it.
USING THE VACUUM CLEANER
Safety measures
• Do not use the vacuum cleaner near hot sur-
faces, such as ashtrays and in places where
inflammable liquids are stored.
• Take sharp objects away from the floor before
cleaning to prevent damage to the unit.
• If the suction power of the vacuum cleaner
decreases rapidly while cleaning, switch it off
immediately and check the telescopic pipe
(4) and the flexible hose (7) for obstruction.
Switch the vacuum cleaner off, then unplug
it, remove the obstruction and only after that
continue cleaning.
USING THE VACUUM CLEANER
Attention! You may switch the vacuum cleaner
on only with the dust bin (11) installed with the
HEPA filter (19) installed in the dust bin, and with
the outlet filter (23) installed. Before switching
the vacuum cleaner on always make sure that the
filters (19, 23) are installed properly.
• Before using the unit unwind the power cord
to the required length and insert the plug into
the socket.
• The yellow mark on the power cord indicates
the maximum cord length. Do not unwind the
power cord further than the red mark.
• Press the on/off button (17) to switch the vac-
uum cleaner on.
• During the operation you can control the suc-
tion power with the suction power control (15)
and with the manual suction power control (6)
on the flexible hose handle (5).
• After room cleaning switch the vacuum
cleaner off by pressing the on/off button (17)
and unplug the unit.
• To wind the cord press the button (14), hold
the winding cord with hand to avoid its whip-
ping and damage.
• During the breaks you can place the brush (1)
in the brush storage (16).
CLEANING AND CARE
Cleaning the dust bin (11)
Remove garbage and dust from the dust bin (11)
after every room cleaning.
– Switch the vacuum cleaner off and unplug it.
– Take the handle (12), press the lock (13) and
remove the dust bin (11).
– Place the dust bin (11) over a garbage bin.
– Lift the clamp (22) and carefully open the
lower lid.
– Remove accumulated dust and garbage from
dust bin (11).
– Close the lower lid and make sure that it is
fixed with the clamp (22).
– Install the dust bin (11) back to its place and
make sure that it is fixed.
Cleaning the HEPA filter (19)
installed in the dust bin (11)
– Preliminarily remove dust and garbage from
the dust bin (11) as described above.
– Holding by the handle (12) turn the upper
lid (18) counterclockwise and remove it.
– Remove the HEPA filter (19)
– Clean the HEPA filter (19) from dust and gar-
bage and wash it under warm water jet.
– Do not wash the filter (19) in a dishwashing
machine.
– Dry the HEPA filter (19) thoroughly.
– Do not dry the HEPA filter (19) with a hairdryer.
– Remove the separator (20) from the flask (21),
wash it and dry.
– Wash the flask (21), wipe it and dry.
– Install the separator (20) into the flask (21),
make sure that the semicircular ledge on the
separator (20) matches the groove on the
flask (21).
– Install the HEPA filter (19) back to its place.
– Install the upper lid (18) back to its place, first
match the mark «▼» on the lid (18) with the
mark «
▲
» on the flask (21) and turn the lid
(18) in the directions of the marks «
▲
» until
bumping.
– Install the assembled dust bin (11) back to its
place, make sure that the dust bin (11) is fixed
properly.
Attention!
Before installing the dust bin (11) make sure that
the HEPA filter is dry and there is no moisture
inside the dust bin (11).
Cleaning the outlet filter (23)
• Switch the vacuum cleaner off and unplug it.
• Turn the grid (24) counterclockwise and
remove it.
• Press on the outlet filter lock and remove the
filter (23).
IM VT-8120.indd 5 05.03.2018 12:58:50

Содержание

Похожие устройства

Скачать