Hitachi WR12DAF2_1.5Ah [15/94] English
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Hitachi WR12DAF2_1.5Ah [15/94] English

Hitachi WR12DAF2_1.5Ah [15/94] English
English
14
MAINTENANCE AND INSPECTION
1. Inspecting the driver bit (WH12DAF2)
Using a broken bit or one with a worn out tip is
dangerous because the bit can slip. Replace it.
2. Inspecting the socket (WR12DAF2)
A worn or deformed hex. or a square-holed socket
will not give an adequate tightness to the fitting
between the nut or anvil, consequently resulting in
loss of tightening torque. Pay attention to wear of a
socket holes periodically, and replace with a new one
if needed.
3. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure
that they are properly tightened. Should any of the
screws be loose, retighten them immediately. Failure
to do so may result in serious hazard.
4. Cleaning of the outside
When the impact driver is stained, wipe with a soft
dry cloth or a cloth moistened with soapy water. Do
not use chloric solvents, gasoline or paint thinner, as
they melt plastics.
5. Storage
Store the impact driver in a place in which the
temperature is less than 40°C, and out of reach of
children.
6. Service parts list
A : Item No.
B : Code No.
C : No. Used
D : Remarks
CAUTION:
Repair, modification and inspection of Hitachi Power
Tools must be carried out by an Hitachi Authorized
Service Center.
This Parts List will be helpful if presented with the
tool to the Hitachi Authorized Service Center when
requesting repair or other maintenance.
In the operation and maintenance of power tools, the
safety regulations and standards prescribed in each
country must be observed.
MODIFICATIONS:
Hitachi Power Tools are constantly being improved
and modified to incorporate the latest technological
advancements.
Accordingly, some parts (i.e. code numbers and/or
design) may be changed without prior notice.
NOTE:
Due to HITACHI’s continuing program of reserch and
development, the specifications herein are subject to
change without prior notice.
Information concerning airborne noise and vibration
The measured values were determined according to
EN50260.
The typical A-weighted sound pressure level: 95 dB
The typical A-weighted sound power level: 108 dB
Wear ear protection.
The typical weighted root mean square acceleration
value: 9.6 m/s
2
(WH12DAF2)
7.6 m/s
2
(WR12DAF2)

Содержание

Похожие устройства

English MAINTENANCE AND INSPECTION 1 Inspecting the driver bit WH12DAF2 Using a broken bit or one with a worn out tip is dangerous because the bit can slip Replace it 2 Inspecting the socket WR12DAF2 A worn or deformed hex or a square holed socket will not give an adequate tightness to the fitting between the nut or anvil consequently resulting in loss of tightening torque Pay attention to wear of a socket holes periodically and replace with anew one if needed 3 Inspecting the mounting screws Regularly inspect all mounting screws and ensure that they are properly tightened Should any of the screws be loose retighten them immediately Failure to do so may result in serious hazard 4 Cleaning of the outside When the impact driver is stained wipe with a soft dry cloth or a cloth moistened with soapy water Do not use chloric solvents gasoline or paint thinner as they melt plastics 5 Storage Store the impact driver in a place in which the temperature is less than 40 C and out of reach of children 6 Service parts list A Item No B Code No C No Used D Remarks CAUTION Repair modification and inspection of Hitachi Power Tools must be carried out by an Hitachi Authorized Service Center This Parts List will be helpful if presented with the tool to the Hitachi Authorized Service Center when requesting repair or other maintenance In the operation and maintenance of power tools the safety regulations and standards prescribed in each country must be observed MODIFICATIONS Hitachi Power Tools are constantly being improved and modified to incorporate the latest technological advancements Accordingly some parts i e code numbers and or design may be changed without prior notice NOTE Due to HITACHI S continuing program of reserch and development the specifications herein are subject to change without prior notice Information concerning airborne noise and vibration The measured values were determined according to EN 50260 The typical A weighted sound pressure level 95 dB The typical A weighted sound power level 108 dB Wear ear protection The typical weighted root mean square acceleration value 9 6 m s2 WH12DAF2 7 6 m s2 WR12DAF2 14

Скачать