Loewe OLED56437D50 Bild 7.77 Graphite Grey [10/52] Подключение телевизора

Loewe OLED56437D50 Bild 7.77 Graphite Grey [10/52] Подключение телевизора
Loewe bild 7
Operating Manual
english
10
Connecting the TV set
Connecting to the mains supply
Remove the cover for the connections.
Connect the TV set to a 220-240V mains socket:
First plug the smaller plug (small connector) of the power cord into
the AC inlet (AC IN) on the TV set, and then the larger connector (Euro
plug) into a mains socket.
Connecting antennas
Cable (analogue) / DVB-C / DVB-T antenna:
Plug the cable of antenna, cable TV system or room antenna into the
ANT TV socket.
If you want to use analogue cables / DVB-C connection and a DVB-T
antenna together, use an external antenna switch (available from
your dealer).
Satellite antenna DVB-S:
Depending on the used satellite system, connect a connecting cable
from the multi-switch or directly from the LNC to the ANT-SAT and
ANT-SAT2 sockets of the TV set respectively.
When connecting the TV set to a single cable community antenna,
connect the ANT-SAT and ANT-SAT2 sockets directly to the
appropriate SAT antenna socket.
When connecting the TV set to a DiSEqC single cable community
antenna (in accordance with EN 50494), connect the ANT-SAT
socket directly to the appropriate SAT antenna socket.
In case of a DiSEqC one cable communal system you require only
one antenna cable. Further distribution of the signal to the two
reception routes is accomplished by the TV set’s satellite tuner.
It is possible, however, to continue using an existing SAT cabling
with two antenna cables in a DiSEqC one cable communal system.
If two transmission channels of the DiSEqC single cable community
exist, one system channel is used per satellite antenna cable.
Ask your dealer in this regard.
Connecting the TV set to the Home network
You may link your TV set to the home network by a wired connection
(Ethernet, Powerline adapters separately available) or by a wireless
radio connection (WLAN). For wireless connections, the TV set has
an internal WLAN antenna.
In order to play back data from your home network your Loewe TV
supports the UPnP AV standard.
You call the network wizard to configure the network adaptor (System
settingsטMultimedia/Network טNetwork settingsטNet-
working).
Under no circumstances may the TV set be wired and at the same
time connected by a wireless connection to the same network, e.g.
router. This may cause severe operational faults!
Example for a wired connection
Connect the LAN socket of your TV set to the LAN switch/router of
your home network with a network cable (available from your dealer).
R TV
Cable
analogue /
DVB-C
DVB-T DVB-S
DSL
LAN switch/router
TV set
PC
Preparing the TV set
Loewe bild 7
Руководство по эксплуатации
Подключение телевизора
Подключение телевизора
Подключение к электрической сети
Удалите заглушку с разъемов.
Подключите телевизор к розетке сети 220-240 В.
Вначале подключите меньший разъем кабеля питания к разъему на
задней панели телевизора AC IN, затем вставьте сетевую вилку
в розетку.
Подключение антенны
Аналоговый кабель антенны / DVB-C / DVB-T.
Подключается к разъему ANT TV. При необходимости подключения
одновременного подключения DVB-C и DVB-T кабелей используйте
внешний переходник (приобретается у дилера).
Спутниковая антенна DVB-S:
В зависимости от используемой системы спутникового
вещания подключается через мультисвитч или напрямую к
соответствующему разъему – ANT-SAT или ANT-SAT2.
При подключении телевизора к общей антенне одним кабелем
включите кабель в соответствующий разъем ANT-SAT или ANT-
SAT2.
При подключении телевизора к кабельной антенне общего
пользования DiSEqC соответствии с EN 50494), подключите
гнездо ANT-SAT напрямую к соответствующему антенному гнезду
S AT.
В случае использования кабельной системы общего пользования
DiSEqC, Вам потребуется только один антенный кабель.
Дальнейшее распределение сигнала по двум каналам приёма
осуществляется спутниковым тюнером телевизора.
Существует возможность продолжать использование текущего
подключения SAT с двумя антенными кабелями DiSEqC в общей
системе пользования При необходимости обратитесь к дилеру за
консультацией.
Подключение телевизора к домашней сети
Подключение возможно как по проводам (Ethernet, адаптеры
Powerline), так и без проводов (WLAN). Для беспроводного
подключения телевизор оснащен внутренней антенной.
Для воспроизведения контента из домашней сети телевизор Loewe
поддерживает стандарт UPnP AV.
Настройка сетевого подключения производится в меню (Системные
настройки - Мультимедиа/Сеть - Сетевые настройки).
Ни в коем случае не подключайте телевизор к одной сети по
проводному и беспроводному подключению. Это может повлечь
ошибки в работе.
Пример проводного подключения
Подключите разхем LAN телевизора к разъему роутера домашней
сети при помощи сетевого кабеля (приобретается у дилера).
Аналоговый
кабель /
Телевизор Сетевой роутер Компьютер

Содержание

Похожие устройства

Скачать