Home
Главная
Vitek
Утюг
VT-8321
Инструкция по эксплуатации Страница: 4

Vitek VT-8321 [4/32] English

ENGLISH

• The unit is not intended for usage by physi-

cally or mentally disabled persons (including

children) or by persons lacking experience or

knowledge if they are not under supervision of

a person who is responsible for their safety or

if they are not instructed by this person on the

usage of the unit.

• Do not use the unit if the power cord or the

plug is damaged, if the unit works improp-

erly or after it was dropped or in case of

leakage.

• Do not use the unit if the power plug or the

power cord is damaged. If the power cord is

damaged, it should be replaced by the manu-

facturer, maintenance service or similar quali-

fied personnel to avoid danger.

• Do not attempt to repair the unit. Do not disas-

semble the unit by yourself, if any malfunction

is detected or after it was dropped, unplug

the unit and apply to any authorized service

center from the contact address list given in

the warranty certificate and on the website

www.vitek.ru.

• Transport the unit in the original package

only.

• Keep the unit out of reach of children and dis-

abled persons.

THE UNIT IS INTENDED FOR HOUSEHOLD USE

ONLY, ITS COMMERCIAL USAGE AND USAGE

IN PRODUCTION AREAS AND WORK SPACES IS

PROHIBITED.

BEFORE THE FIRST USE

After unit transportation or storage at low

temperature keep it for at least three hours

at room temperature before switching on.

• Unpack the iron; remove the protection from

the soleplate (14), if any.

• Check the unit for damages, do not use the

iron in case of damages.

• Before switching the iron on, make sure that

your home mains voltage corresponds to the

iron operating voltage.

• There may be water residue in the tank, this

is normal, as the iron has undergone factory

quality control.

Note: While the first switching on the heating

element of the iron burns, therefore occurrence

of foreign smell and a small amount of smoke is

possible, it is normal.

WATER SELECTION

You can use tap water to fill the water tank (10).

If tap water is hard, use distilled or demineral-

ized water, this will prolong service life of the

iron.

Note: Do not fill the water tank (10) with scented

liquids, vinegar, starch solution, descaling

reagents, chemical agents etc.

FILLING THE WATER TANK

Before filling the iron with water, make sure that

it is unplugged.

• Set the temperature control knob (11) to the

position «OFF», and the continuous steam

supply knob (3) to the position «•» – continu-

ous steam supply is off.

• Open the lid (2) and pour water into the water

tank (10) using the beaker (15) and then close

the lid (2) tight.

Note:

• Do not exceed the «MAX» mark (13).

• If you need to refill water during ironing,

always switch the iron off first and unplug it.

• After you finish ironing, switch the iron off,

wait until it cools down completely, then open

the water inlet lid (2), turn over the iron and

drain the remaining water.

IRONING TEMPERATURE

Before operation, test the heated iron on a piece

of cloth to be sure that the iron soleplate (14) and

the water tank (10) are clean.

• Always check the recommended ironing tem-

perature indicated on the tag before ironing.

• If the item label is marked with the symbol

, do not iron the item.

• If there is no tag with recommended ironing

temperature, but you know the type of fab-

ric, use the following table to determine the

proper temperature.

Ironing temperature table

Icons Fabric type (temperature)

do not iron

•

Synthetics, nylon, acryl, polyester

(low temperature)

••

Silk/wool (medium temperature)

•••

Cotton (high temperature)

МАХ

Linen (high temperature)

IM VT-8321.indd 4 24.12.2018 14:17:04

Vitek VT-8321 [4/32] English

Содержание

Похожие устройства