Home
Главная
Vitek
Пылесос
VT-8136
Инструкция по эксплуатации Страница: 6

Vitek VT-8136 [6/28] English

ENGLISH

Attachment holder (31)

For easy storing of attachments (29, 30), the set

includes an attachment holder (31).

Install the holder (31) on the telescopic pipe (4) and

install the attachments (29, 30) into it.

Dust bin (11)

The dust bin (11) is equipped with a cyclonic filter,

which sifts out garbage and dust from the intake

air, while the filter block (16) retains the finest dust

particles.

Note: - provide that the filter block (16) is always

clean, because the overall performance of the vac

uum cleaner depends on it.

USING THE VACUUM CLEANER

Safety measures

•

Do not use the vacuum cleaner near hot sur-

faces, such as ashtrays and in places where

inflammable liquids are stored.

•

Take sharp objects away from the floor before

cleaning to prevent the unit damage.

•

If the suction power of the vacuum cleaner

decreases rapidly while cleaning, switch it off

immediately and check the telescopic pipe (4)

and the flexible hose (7) for obstruction. Switch

the vacuum cleaner off, then unplug it, remove

the obstruction and only after that continue

cleaning.

USING THE VACUUM CLEANER

Attention! You may switch the vacuum cleaner on

only with the dust bin (11), with the filter block (16)

and the outlet HEPA filter (27) installed in the

dust bin. Before switching the vacuum cleaner

on, always make sure that the filters (16, 27) are

installed properly.

•

Before using the unit, unwind the power cord to

the required length and insert the power plug

into the mains socket.

•

The yellow mark on the power cord indicates the

maximum cord length. Do not unwind the power

cord further than the red mark.

•

Press the ON/OFF button (28) to switch the vac-

uum cleaner on.

•

During the operation you can control the suc-

tion power using the suction power control (22)

or the manual suction power control (6) on the

flexible hose handle (5).

•

After room cleaning switch the vacuum cleaner

off by pressing the ON/OFF button (28) and

unplug the unit.

•

To wind the power cord, press the button (23),

hold the winding cord with your hand to avoid its

whipping and damage.

•

During breaks in cleaning, you can place the

brush (1) in the brush storage (24).

Note: - before replacing the brush (1), setting the

attachments (29, 30) or cleaning the dust bin (11),

switch the vacuum cleaner off and take the power

plug out of the mains socket.

CLEANING AND CARE

Cleaning the dust bin (11)

Remove garbage and dust from the dust bin (11)

after every room cleaning.

–

Switch the vacuum cleaner off and unplug it.

–

Take the handle (12), press the lock (21) and

remove the dust bin (11).

–

Place the dust bin (11) over a garbage bin.

–

Pull the lock (13) to release the lid (14) (pic. 1)

–

Remove accumulated dust and garbage from

dust bin (11).

–

Close the lid (14).

–

Install the dust bin (11) back to its place.

Cleaning the separator (20) and the filter

block (16) installed in the dust bin (11)

–

First remove dust and garbage from the dust

bin (11) as described above.

–

Pull the lock (18) and open the lid (17).

–

Remove the filter block (16), take the microfoam

filter out of the filter block (16).

–

Close the lid (17), take the handle (12) and turn

the cyclonic filter counterclockwise “ ” and

remove it (pic. 2, 3).

–

Turn the lock ring (19) counterclockwise

(“open”) and remove it (pic. 4).

–

Remove the separator (20) and wash it under a

warm water jet (pic. 4, 5).

–

Clean the filter block (16) and the microfoam fil-

ter from dust and garbage and wash them under

warm water jet.

–

Do not wash filters in a dishwashing machine.

–

Dry the filter block (16) and the microfoam filter

thoroughly.

–

Do not dry filters with a hairdryer.

–

Wash the dust bin flask (15), wipe it and dry.

–

Install the separator (20) back to its place

matching the grooves on the separator (20) with

the ledges on the cyclonic filter.

–

Install the lock ring (19) back to its place and turn

it clockwise (“close”) as far as it will go.

–

Install the cyclonic filter into the flask (15)

matching the mark on the cyclonic filter with

IM VT-8136.indd 6 13.12.2018 17:22:36

Vitek VT-8136 [6/28] English

Содержание

Похожие устройства