Dahua DHI-ARC2000B-W [2/2] Product installation
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Dahua DHI-ARC2000B-W [2/2] Product installation

Dahua DHI-ARC2000B-W [2/2] Product installation

Содержание

Похожие устройства

Step 9 Observe status of hub indicator If it turns from slow pulse red to solid blue it is connected successfully Press Yes to continue If it turns from slow pulse red to solid red it fails to be Tamperproof Switch connected Press Load Again to repeat above steps Step 5 Select device hotspot input the hotspot password Figure 3 28 hotspot name is device SN and default password is Figure 4 1 4 2 Installation with Foam Rubber 12345678 connect the mobile phone to device hotspot and connect EQ Note Figure 3 23 If the mobile phone has once connected this device hotspot it has no need to input hotspot password again Step 10 Input hub name and press ViewAlarm Hub Press to arm or disarm 2M065D3PAN00003 3 5 Detector Enters Armed Mode Step 1 Paste 3M foam rubber on the bracket Only when the detector is enabled can the alarm be triggered Step 2 Paste the device to an appropriate position on the wall under arm mode T Caution After enabling the detector it shall be armed again to take effect Excellent Step 1 Press first and then press Display mode setting WPA2 PSK interface S CANCEL Q1 Intelligent alarm hub cannot be booted normally A Please check input power of the hub including adapter and USB cable Q2 Accessory pairing fails A Please check if the hub is in wireless pairing mode Please check if electric quantity of accessory battery is sufficient Please check if the accessory has connected with other hubs Please clear configuration and try pairing again Please check if the accessory is too far away from the hub and beyond effective range Please move the detector closer and try pairing again CONNECT Figure 3 17 Figure 3 24 Q3 Accessory is triggered without any response A Please check if electric quantity of accessory battery is sufficient Please check if the accessory has been added to arm mode Please check if the hub is armed Please check if cables of the accessory drop off Please check if the accessory exceeds detection scope Figure 3 29 Q4 Mobile phone client doesn t receive messages after an alarm is triggered A Please check if network connection of the hub or router is normal Please check if alarm subscription of APP is enabled Figure 3 18 Step 6 In APP interface press Connected next step Step 7 Press scan QR code on the back of the device obtain device SN and input device password Start to search nearby available WiFi EQ Note Figure 3 25 ZhsCaution Make sure that the device has completed initialization and Figure 3 30 network configuration Password is the password set during device Q5 The accessory goes online and offline frequently A Please check if the hub or accessory is power off frequently Please check if the hub network is normal Please check if the accessory is too far away from the hub and at the critical state of communication 3 3 3 P2P Scanning Step 1 In Add Device interface press Add Device initialization Step 2 Press Q to enable the detector Press menu key at the top to switch armed mode ___ stay S away E3 custom Step 3 Press D to save the settings Appendix 1 Technical Parameters Parameter 3 6 Clear Detector Siren Pairing Info MT7688AN Wireless Carrier Frequency 433 868 915MHz WiFi Carrier Frequency 2 4GHz support 802 11 b g n If the detector needs to be used with a new hub or restore Figure 3 26 Figure 3 19 Standard factory defaults slide the tamperproof switch of the case for 5 Wireless Transmitting Power times quickly to clear config info and restore factory defaults WiFi Transmitting Power 18dBm The indicator light will be normally on and then flash if it clears Wireless Transmission 1000m open air Distance 3 7 Remote Control Paring Wireless Device Access Max 32 Supply Voltage DC5V Through pairing multiple wireless remote controls can be Power Consumption 5W bound with the hub so as to realize quick arm disarm and Working Temperature 10 C 55 C emergency alarm function Installation Desktop and wall mounted Step 1 Short press the function key of hub to enter pairing Dimension then the hub gives off the prompt tone of beep which means paring success Otherwise pairing fails Please pairagain EQ Note After entering pairing mode multiple wireless remote controls can be added in sequence Disarm Figure 3 27 input password and press OK At this time red indicator flashes slowly indicating hub is connecting selected WiFi Step 2 Press scan QR code on the back of the device Emergency Alarm obtain device SN input hub name and password Step3 Press ViewAlarm Hub Press Q to arm or disarm 3 4 Detector Siren Pairing In pairing mode of the hub multiple detectors and sirens can be Figure 3 31 added one by one Step 1 Short press the function key of hub to enter pairing mode and then the blue indicator flashes quickly 3 8 Delete Detector Siren and Remote Control Step 2 Power on the detector siren Its indicator light is normally on and then flashes fast representing that it enters pairing mode and starts pairing Pair successfully when the hub gives off prompt tone of beep Fail to pair if red light flashes slowly for 3 times Repeat above steps until it is paired successfully Or slide the tamperproof switch of the case and pair Method 1 In APP check accessory details and delete according to prompts Method 2 Press the RESET button for 6s when the power is on until indicator is off then hub will restart and red flashes slowly indicating all config info has been cleared and factory default settings have been restored manually EQ Note Hub paring process will last 120s After that exit pairing Product Installation mode automatically and blue indicator light is normally on During pairing short press the function key to stop pairing manually Take wireless PIR detector as an example position of tamperproof switch is shown as follows This product provides installation with screw and foam rubber 4 1 Installation with Screw Step 1 Take down the bracket and drill holes in the wall according to bracket hole positions Step 2 Insert expansion pipe into the hole Step 3 Fix the bracket with self tapping screw Step 4 Buckle the hub into the bracket from top to bottom Figure 3 22 140mmx142mmx19 5mm length width thickness Step 2 Press any key of wireless remote control for 2s and Step 8 In the list of available WiFi network select the WiFi s 10dBm successfully mode and then blue indicatorflashes quickly Figure 3 20 Description Main Processor Weight 0 2kg

Скачать