![Tp-Link T2500G-10TS V1 [182/365] Tracert](/img/pdf.png)
Tp-Link T2500G-10TS V1 [182/365] Tracert
![Tp-Link T2500G-10TS V1 [182/365] Tracert](/views2/1470624/page182/bgb6.png)
166
T2500G-10TS# ping 192.168.0.131 –n 8 –l 512
To test the connectivity between the switch and the network device with the
IP fe80::1234, please specify the
count
(-l) as 512 bytes and
count
(-i) as 1000
milliseconds. If there is not any response after 8 times’ Ping test, the
connection between the switch and the network device is failed to establish:
T2500G-10TS# ping fe80::1234 –n 8 –l 512
21.18 tracert
Description
The tracert command is used to test the connectivity of the gateways during
its journey from the source to destination of the test data.
Syntax
tracert [ ip | ipv6 ]
ip_addr
[
maxHops
]
Parameter
ip —— The type of the IP address for tracert test should be IPv4.
ipv6 —— The type of the IP address for tracert test should be IPv6.
ip_addr
—— The IP address of the destination device. If the parameter ip/ipv6
is not selected, both IPv4 and IPv6 addresses are supported, for example
192.168.0.100 or fe80::1234.
maxHops
—— The maximum number of the route hops the test data can pass
though. It ranges from 1 to 30. By default, this value is 4.
Command Mode
User EXEC Mode and Privileged EXEC Mode
Privilege Requirement
Only Admin, Operator and Power User level users have access to these
commands.
Example
Test the connectivity between the switch and the network device with the IP
192.168.0.131. If the destination device has not been found after 20
maxHops
,
the connection between the switch and the destination device is
failed to establish:
T2500G-10TS# tracert 192.168.0.131 20
Содержание
- Cli reference guide 1
- T2500g 10ts tl sg3210 1
- Copyright trademarks 2
- Chapter 1 using the cli 4 3
- Chapter 2 user interface 20 3
- Chapter 3 ieee 802 q vlan commands 28 3
- Contents 3
- Preface 1 3
- Chapter 4 mac based vlan commands 37 4
- Chapter 5 protocol based vlan commands 40 4
- Chapter 6 vlan vpn commands 44 4
- Chapter 7 voice vlan commands 50 4
- Chapter 10 etherchannel commands 65 5
- Chapter 11 user management commands 71 5
- Chapter 8 l2pt commands 56 5
- Chapter 9 gvrp commands 60 5
- Chapter 12 http and https commands 83 6
- Chapter 13 binding table commands 92 6
- Chapter 14 arp inspection commands 105 6
- Chapter 15 dos defend commands 111 7
- Chapter 16 ieee 802 x commands 114 7
- Chapter 17 pppoe id insertion commands 127 7
- Chapter 18 system log commands 132 8
- Chapter 19 ssh commands 139 8
- Chapter 20 mac address commands 145 8
- Chapter 21 system configuration commands 153 8
- Chapter 22 ipv6 address configuration commands 173 9
- Chapter 23 ethernet configuration commands 179 10
- Chapter 24 qos commands 189 10
- Chapter 25 port mirror commands 197 10
- Chapter 26 port isolation commands 200 10
- Chapter 27 loopback detection commands 202 11
- Chapter 28 acl commands 208 11
- Chapter 29 mstp commands 225 11
- Chapter 30 dldp commands 244 12
- Chapter 31 igmp snooping commands 249 12
- Chapter 32 mld snooping commands 267 13
- Chapter 33 snmp commands 288 14
- Chapter 34 lldp commands 311 15
- Chapter 35 aaa commands 322 15
- Chapter 36 dhcp relay commands 344 16
- Overview of this guide 17
- Preface 17
- Accessing the cli 20
- Chapter 1 using the cli 20
- Logon by a console port 20
- Logon by telnet 22
- Logon by ssh 26
- Cli command modes 31
- Configuration 32
- Exec mode 32
- Global 32
- Interface configuration mode can also be divided into interface ethernet interface 32
- Link aggregation and some other modes which is shown as the following diagram 32
- Logout or access the 32
- Mode accessing path prompt 32
- Next mode 32
- Privileged 32
- The following table gives detailed information about the accessing path prompt of each mode and how to exit the current mode and access the next mode 32
- User exec 32
- Configuration 33
- Each command mode has its own set of specific commands to configure some 33
- Interface 33
- Logout or access the 33
- Mode accessing path prompt 33
- Next mode 33
- Switch is established by a telnet ssh connection 33
- The user is automatically in user exec mode after the connection between the pc and the 33
- Privilege restrictions 34
- Conventions 35
- Format conventions 35
- Parameter format 35
- Special characters 35
- Chapter 2 user interface 36
- Command mode 36
- Description 36
- Enable 36
- Enable admin 36
- Example 36
- Privilege requirement 36
- Syntax 36
- Command mode 37
- Description 37
- Example 37
- Privilege requirement 37
- Service password encryption 37
- Syntax 37
- User guidelines 37
- Command mode 38
- Description 38
- Enable password 38
- Parameter 38
- Privilege requirement 38
- Syntax 38
- User guidelines 38
- Command mode 39
- Description 39
- Enable secret 39
- Example 39
- Parameter 39
- Privilege requirement 39
- Syntax 39
- Command mode 40
- Configure 40
- Description 40
- Example 40
- Privilege requirement 40
- Syntax 40
- User guidelines 40
- Clipaging 41
- Command mode 41
- Description 41
- Example 41
- Privilege requirement 41
- Syntax 41
- Clear history 42
- Command mode 42
- Description 42
- Example 42
- Privilege requirement 42
- Show history 42
- Syntax 42
- Command mode 43
- Example 43
- Privilege requirement 43
- Syntax 43
- Chapter 3 ieee 802 q vlan commands 44
- Command mode 44
- Description 44
- Example 44
- Parameter 44
- Privilege requirement 44
- Syntax 44
- Command mode 45
- Description 45
- Example 45
- Interface vlan 45
- Parameter 45
- Privilege requirement 45
- Syntax 45
- Command mode 46
- Description 46
- Example 46
- Parameter 46
- Privilege requirement 46
- Switchport mode 46
- Syntax 46
- Command mode 47
- Description 47
- Example 47
- Parameter 47
- Privilege requirement 47
- Switchport access vlan 47
- Switchport trunk allowed vlan 47
- Syntax 47
- Command mode 48
- Description 48
- Example 48
- Parameter 48
- Privilege requirement 48
- Switchport trunk allowed vlan all 48
- Syntax 48
- Command mode 49
- Description 49
- Example 49
- Parameter 49
- Privilege requirement 49
- Switchport general allowed vlan 49
- Syntax 49
- Command mode 50
- Description 50
- Example 50
- Parameter 50
- Privilege requirement 50
- Show vlan summary 50
- Switchport pvid 50
- Syntax 50
- Command mode 51
- Description 51
- Example 51
- Parameter 51
- Privilege requirement 51
- Show vlan 51
- Show vlan brief 51
- Syntax 51
- Command mode 52
- Description 52
- Example 52
- Parameter 52
- Privilege requirement 52
- Show interface switchport 52
- Syntax 52
- Chapter 4 mac based vlan commands 53
- Command mode 53
- Description 53
- Example 53
- Mac vlan mac address 53
- Parameter 53
- Privilege requirement 53
- Syntax 53
- Command mode 54
- Description 54
- Example 54
- Mac vlan 54
- Privilege requirement 54
- Show mac vlan 54
- Syntax 54
- Example 55
- Parameter 55
- Privilege requirement 55
- Chapter 5 protocol based vlan commands 56
- Command mode 56
- Description 56
- Parameter 56
- Privilege requirement 56
- Protocol vlan template 56
- Syntax 56
- Command mode 57
- Description 57
- Example 57
- Parameter 57
- Privilege requirement 57
- Protocol vlan vlan 57
- Syntax 57
- Command mode 58
- Description 58
- Example 58
- Parameter 58
- Privilege requirement 58
- Protocol vlan group 58
- Show protocol vlan template 58
- Syntax 58
- Command mode 59
- Description 59
- Example 59
- Privilege requirement 59
- Show protocol vlan vlan 59
- Syntax 59
- Chapter 6 vlan vpn commands 60
- Command mode 60
- Description 60
- Dot1q tunnel 60
- Dot1q tunnel tpid 60
- Example 60
- Privilege requirement 60
- Syntax 60
- Command mode 61
- Description 61
- Dot1q tunnel mapping 61
- Example 61
- Parameter 61
- Privilege requirement 61
- Syntax 61
- Command mode 62
- Description 62
- Example 62
- Parameter 62
- Privilege requirement 62
- Switchport dot1q tunnel mapping 62
- Syntax 62
- Command mode 63
- Description 63
- Example 63
- Privilege requirement 63
- Switchport dot1q tunnel missdrop 63
- Switchport dot1q tunnel mode uplink 63
- Syntax 63
- Command mode 64
- Description 64
- Example 64
- Privilege requirement 64
- Show dot1q tunnel 64
- Show dot1q tunnel mapping 64
- Syntax 64
- Command mode 65
- Description 65
- Example 65
- Privilege requirement 65
- Show dot1q tunnel interface 65
- Syntax 65
- Chapter 7 voice vlan commands 66
- Command mode 66
- Description 66
- Example 66
- Parameter 66
- Privilege requirement 66
- Syntax 66
- Voice vlan 66
- Voice vlan aging time 66
- Command mode 67
- Description 67
- Example 67
- Parameter 67
- Privilege requirement 67
- Syntax 67
- Voice vlan priority 67
- Command mode 68
- Description 68
- Example 68
- Parameter 68
- Privilege requirement 68
- Syntax 68
- Voice vlan mac address 68
- Command mode 69
- Description 69
- Example 69
- Parameter 69
- Privilege requirement 69
- Switchport voice vlan mode 69
- Switchport voice vlan security 69
- Syntax 69
- Command mode 70
- Description 70
- Example 70
- Privilege requirement 70
- Show voice vlan 70
- Show voice vlan oui 70
- Syntax 70
- Command mode 71
- Description 71
- Example 71
- Parameter 71
- Privilege requirement 71
- Show voice vlan switchport 71
- Syntax 71
- Chapter 8 l2pt commands 72
- Command mode 72
- Description 72
- Example 72
- L2protocol tunnel 72
- L2protocol tunnel type 72
- Privilege requirement 72
- Syntax 72
- Command mode 73
- Parameter 73
- Privilege requirement 73
- Syntax 73
- Command mode 74
- Description 74
- Example 74
- Parameter 74
- Privilege requirement 74
- Show l2protocol tunnel global 74
- Show l2protocol tunnel interface 74
- Syntax 74
- Command mode 75
- Example 75
- Privilege requirement 75
- Chapter 9 gvrp commands 76
- Command mode 76
- Description 76
- Example 76
- Gvrp interface 76
- Privilege requirement 76
- Syntax 76
- Command mode 77
- Description 77
- Example 77
- Gvrp registration 77
- Parameter 77
- Privilege requirement 77
- Syntax 77
- Command mode 78
- Description 78
- Example 78
- Gvrp timer 78
- Parameter 78
- Syntax 78
- Command mode 79
- Description 79
- Example 79
- Parameter 79
- Privilege requirement 79
- Show gvrp interface 79
- Syntax 79
- Command mode 80
- Description 80
- Example 80
- Privilege requirement 80
- Show gvrp global 80
- Syntax 80
- Channel group 81
- Chapter 10 etherchannel commands 81
- Command mode 81
- Description 81
- Parameter 81
- Privilege requirement 81
- Syntax 81
- Command mode 82
- Description 82
- Example 82
- Parameter 82
- Port channel load balance 82
- Privilege requirement 82
- Syntax 82
- Command mode 83
- Description 83
- Example 83
- Lacp port priority 83
- Lacp system priority 83
- Parameter 83
- Privilege requirement 83
- Syntax 83
- Command mode 84
- Description 84
- Example 84
- Parameter 84
- Privilege requirement 84
- Show etherchannel 84
- Syntax 84
- Command mode 85
- Description 85
- Example 85
- Parameter 85
- Privilege requirement 85
- Show etherchannel load balance 85
- Show lacp 85
- Syntax 85
- Command mode 86
- Description 86
- Example 86
- Privilege requirement 86
- Show lacp sys id 86
- Syntax 86
- Chapter 11 user management commands 87
- Description 87
- Parameter 87
- Syntax 87
- User name password 87
- Command mode 88
- Description 88
- Example 88
- Parameter 88
- Privilege requirement 88
- Syntax 88
- User guidelines 88
- User name secret 88
- Command mode 89
- Description 89
- Example 89
- Privilege requirement 89
- User access control ip based 89
- User guidelines 89
- Command mode 90
- Description 90
- Example 90
- Parameter 90
- Privilege requirement 90
- Syntax 90
- User access control mac based 90
- Command mode 91
- Description 91
- Example 91
- Parameter 91
- Privilege requirement 91
- Syntax 91
- User access control port based 91
- Command mode 92
- Description 92
- Example 92
- Parameter 92
- Privilege requirement 92
- Syntax 92
- Command mode 93
- Description 93
- Example 93
- Parameter 93
- Password 93
- Privilege requirement 93
- Syntax 93
- Command mode 94
- Description 94
- Example 94
- Privilege requirement 94
- Syntax 94
- User guidelines 94
- Command mode 95
- Description 95
- Example 95
- Login local 95
- Media type rj45 95
- Privilege requirement 95
- Syntax 95
- Command mode 96
- Description 96
- Example 96
- Privilege requirement 96
- Syntax 96
- Telnet 96
- Command mode 97
- Description 97
- Example 97
- Privilege requirement 97
- Show user account list 97
- Show user configuration 97
- Syntax 97
- Command mode 98
- Description 98
- Example 98
- Privilege requirement 98
- Show telnet status 98
- Syntax 98
- Chapter 12 http and https commands 99
- Command mode 99
- Description 99
- Example 99
- Ip http server 99
- Privilege requirement 99
- Syntax 99
- Command mode 100
- Description 100
- Example 100
- Ip http max users 100
- Ip http session timeout 100
- Parameter 100
- Privilege requirement 100
- Syntax 100
- Command mode 101
- Description 101
- Example 101
- Ip http secure server 101
- Parameter 101
- Privilege requirement 101
- Syntax 101
- Command mode 102
- Description 102
- Example 102
- Ip http secure ciphersuite 102
- Ip http secure protocol 102
- Parameter 102
- Privilege requirement 102
- Syntax 102
- Command mode 103
- Description 103
- Example 103
- Ip http secure max users 103
- Parameter 103
- Privilege requirement 103
- Syntax 103
- Command mode 104
- Description 104
- Example 104
- Ip http secure session timeout 104
- Parameter 104
- Privilege requirement 104
- Syntax 104
- Command mode 105
- Description 105
- Example 105
- Ip http secure server download certificate 105
- Parameter 105
- Privilege requirement 105
- Syntax 105
- Command mode 106
- Description 106
- Example 106
- Ip http secure server download key 106
- Parameter 106
- Privilege requirement 106
- Syntax 106
- Command mode 107
- Description 107
- Example 107
- Privilege requirement 107
- Show ip http configuration 107
- Show ip http secure server 107
- Syntax 107
- Chapter 13 binding table commands 108
- Description 108
- Ip source binding 108
- Parameter 108
- Syntax 108
- Command mode 109
- Description 109
- Example 109
- Ip source binding index 109
- Parameter 109
- Privilege requirement 109
- Syntax 109
- Command mode 110
- Description 110
- Example 110
- Ip dhcp snooping 110
- Privilege requirement 110
- Syntax 110
- Command mode 111
- Description 111
- Example 111
- Ip dhcp snooping global 111
- Parameter 111
- Privilege requirement 111
- Syntax 111
- Command mode 112
- Description 112
- Example 112
- Ip dhcp snooping information option 112
- Ip dhcp snooping information strategy 112
- Privilege requirement 112
- Syntax 112
- Command mode 113
- Description 113
- Example 113
- Ip dhcp snooping information format 113
- Parameter 113
- Privilege requirement 113
- Syntax 113
- Command mode 114
- Description 114
- Example 114
- Ip dhcp snooping information remote id 114
- Parameter 114
- Privilege requirement 114
- Syntax 114
- Command mode 115
- Description 115
- Example 115
- Ip dhcp snooping information circuit id 115
- Parameter 115
- Privilege requirement 115
- Syntax 115
- Command mode 116
- Description 116
- Example 116
- Ip dhcp snooping mac verify 116
- Ip dhcp snooping trust 116
- Privilege requirement 116
- Syntax 116
- Command mode 117
- Description 117
- Example 117
- Ip dhcp snooping limit rate 117
- Parameter 117
- Privilege requirement 117
- Syntax 117
- Command mode 118
- Description 118
- Example 118
- Ip dhcp snooping decline 118
- Privilege requirement 118
- Show ip source binding 118
- Syntax 118
- Command mode 119
- Description 119
- Example 119
- Gigabitethernet 119
- Privilege requirement 119
- Show ip dhcp snooping information 119
- Show ip dhcp snooping interface 119
- Show ip dhcp snooping interface gigabitethernet 119
- Syntax 119
- Command mode 120
- Example 120
- Parameters 120
- Privilege requirement 120
- Chapter 14 arp inspection commands 121
- Command mode 121
- Description 121
- Example 121
- Ip arp inspection global 121
- Ip arp inspection trust 121
- Privilege requirement 121
- Syntax 121
- Command mode 122
- Description 122
- Example 122
- Ip arp inspection interface 122
- Privilege requirement 122
- Syntax 122
- Command mode 123
- Description 123
- Example 123
- Ip arp inspection limit rate 123
- Parameter 123
- Privilege requirement 123
- Syntax 123
- Command mode 124
- Description 124
- Example 124
- Ip arp inspection recover 124
- Privilege requirement 124
- Show ip arp inspection 124
- Syntax 124
- Command mode 125
- Description 125
- Example 125
- Parameter 125
- Privilege requirement 125
- Show ip arp inspection interface 125
- Show ip arp inspection statistics 125
- Syntax 125
- Clear ip arp inspection statistics 126
- Command mode 126
- Description 126
- Example 126
- Privilege requirement 126
- Syntax 126
- Chapter 15 dos defend commands 127
- Command mode 127
- Description 127
- Example 127
- Ip dos prevent 127
- Ip dos prevent type 127
- Privilege requirement 127
- Syntax 127
- Command mode 128
- Description 128
- Example 128
- Parameter 128
- Privilege requirement 128
- Show ip dos prevent 128
- Syntax 128
- Command mode 129
- Example 129
- Privilege requirement 129
- Syntax 129
- Chapter 16 ieee 802 x commands 130
- Command mode 130
- Description 130
- Dot1x system auth control 130
- Example 130
- Privilege requirement 130
- Syntax 130
- Command mode 131
- Description 131
- Dot1x auth method 131
- Dot1x handshake 131
- Example 131
- Parameter 131
- Privilege requirement 131
- Syntax 131
- Command mode 132
- Description 132
- Dot1x accounting 132
- Example 132
- Privilege requirement 132
- Syntax 132
- Command mode 133
- Description 133
- Dot1x vlan assignment 133
- Example 133
- Privilege requirement 133
- Syntax 133
- Command mode 134
- Description 134
- Dot1x guest vlan global 134
- Dot1x quiet period 134
- Example 134
- Parameter 134
- Privilege requirement 134
- Syntax 134
- Command mode 135
- Description 135
- Dot1x timeout supplicant timeout 135
- Example 135
- Parameter 135
- Privilege requirement 135
- Syntax 135
- Command mode 136
- Description 136
- Dot1x max reauth req 136
- Example 136
- Parameter 136
- Privilege requirement 136
- Syntax 136
- Command mode 137
- Description 137
- Dot1x guest vlan interface 137
- Example 137
- Privilege requirement 137
- Syntax 137
- Command mode 138
- Description 138
- Dot1x mab 138
- Example 138
- Privilege requirement 138
- Syntax 138
- Command mode 139
- Description 139
- Dot1x port control 139
- Example 139
- Parameter 139
- Privilege requirement 139
- Syntax 139
- Command mode 140
- Description 140
- Dot1x port method 140
- Example 140
- Parameter 140
- Privilege requirement 140
- Syntax 140
- Command mode 141
- Description 141
- Example 141
- Parameter 141
- Privilege requirement 141
- Show dot1x global 141
- Show dot1x interface 141
- Syntax 141
- Example 142
- Chapter 17 pppoe id insertion commands 143
- Command mode 143
- Description 143
- Example 143
- Pppoe id insertion global 143
- Privilege requirement 143
- Syntax 143
- Command mode 144
- Description 144
- Example 144
- Parameter 144
- Pppoe circuit id interface 144
- Pppoe circuit id type 144
- Privilege requirement 144
- Syntax 144
- Command mode 145
- Description 145
- Example 145
- Parameter 145
- Pppoe remote id 145
- Privilege requirement 145
- Syntax 145
- Command mode 146
- Description 146
- Example 146
- Privilege requirement 146
- Show pppoe id insertion global 146
- Show pppoe id insertion interface 146
- Syntax 146
- Command mode 147
- Example 147
- Parameter 147
- Privilege requirement 147
- Syntax 147
- Chapter 18 system log commands 148
- Command mode 148
- Description 148
- Example 148
- Logging buffer 148
- Parameter 148
- Privilege requirement 148
- Syntax 148
- Command mode 149
- Description 149
- Example 149
- Logging file flash 149
- Logging file flash frequency 149
- Privilege requirement 149
- Syntax 149
- Command mode 150
- Description 150
- Example 150
- Logging file flash level 150
- Parameter 150
- Privilege requirement 150
- Syntax 150
- Command mode 151
- Description 151
- Example 151
- Logging host index 151
- Parameter 151
- Privilege requirement 151
- Syntax 151
- Clear logging 152
- Command mode 152
- Description 152
- Example 152
- Parameter 152
- Privilege requirement 152
- Show logging local config 152
- Syntax 152
- Command mode 153
- Description 153
- Example 153
- Parameter 153
- Privilege requirement 153
- Show logging buffer 153
- Show logging loghost 153
- Syntax 153
- Command mode 154
- Description 154
- Example 154
- Parameter 154
- Privilege requirement 154
- Show logging flash 154
- Syntax 154
- Chapter 19 ssh commands 155
- Command mode 155
- Description 155
- Example 155
- Ip ssh server 155
- Ip ssh version 155
- Privilege requirement 155
- Syntax 155
- Command mode 156
- Description 156
- Example 156
- Ip ssh algorithm 156
- Parameter 156
- Privilege requirement 156
- Syntax 156
- Command mode 157
- Description 157
- Example 157
- Ip ssh max client 157
- Ip ssh timeout 157
- Parameter 157
- Privilege requirement 157
- Syntax 157
- Command mode 158
- Description 158
- Example 158
- Ip ssh download 158
- Parameter 158
- Privilege requirement 158
- Syntax 158
- Command mode 159
- Description 159
- Example 159
- Parameter 159
- Privilege requirement 159
- Remove public key 159
- Show ip ssh 159
- Syntax 159
- Command mode 160
- Example 160
- Privilege requirement 160
- Chapter 20 mac address commands 161
- Command mode 161
- Description 161
- Example 161
- Mac address table static 161
- Parameter 161
- Privilege requirement 161
- Syntax 161
- Command mode 162
- Description 162
- Example 162
- Mac address table aging time 162
- Mac address table filtering 162
- Parameter 162
- Privilege requirement 162
- Syntax 162
- Command mode 163
- Description 163
- Example 163
- Mac address table max mac count 163
- Parameter 163
- Privilege requirement 163
- Syntax 163
- Command mode 164
- Description 164
- Example 164
- Privilege requirement 164
- Show mac address table 164
- Syntax 164
- Clear mac address table 165
- Command mode 165
- Description 165
- Example 165
- Parameter 165
- Privilege requirement 165
- Show mac address table aging time 165
- Syntax 165
- Command mode 166
- Description 166
- Example 166
- Parameter 166
- Privilege requirement 166
- Show mac address table max mac count 166
- Syntax 166
- Command mode 167
- Description 167
- Example 167
- Parameter 167
- Privilege requirement 167
- Show mac address table count 167
- Show mac address table interface 167
- Syntax 167
- Command mode 168
- Description 168
- Example 168
- Parameter 168
- Privilege requirement 168
- Show mac address table address 168
- Show mac address table vlan 168
- Syntax 168
- Chapter 21 system configuration commands 169
- Command mode 169
- Description 169
- Example 169
- Parameter 169
- Privilege requirement 169
- Syntax 169
- System time manual 169
- System time ntp 169
- Command mode 171
- Description 171
- Example 171
- Parameter 171
- Privilege requirement 171
- Syntax 171
- System time dst predefined 171
- Command mode 172
- Description 172
- Example 172
- Parameter 172
- Privilege requirement 172
- Syntax 172
- System time dst date 172
- Command mode 173
- Description 173
- Example 173
- Parameter 173
- Privilege requirement 173
- Syntax 173
- System time dst recurring 173
- Command mode 174
- Description 174
- Example 174
- Hostname 174
- Location 174
- Parameter 174
- Privilege requirement 174
- Syntax 174
- Command mode 175
- Contact info 175
- Description 175
- Example 175
- Parameter 175
- Privilege requirement 175
- Syntax 175
- Command mode 176
- Description 176
- Example 176
- Privilege requirement 176
- Reboot 176
- Syntax 176
- Command mode 177
- Copy running config startup config 177
- Copy startup config tftp 177
- Description 177
- Example 177
- Parameter 177
- Privilege requirement 177
- Syntax 177
- Command mode 178
- Copy tftp startup config 178
- Description 178
- Example 178
- Parameter 178
- Privilege requirement 178
- Syntax 178
- Boot application 179
- Command mode 179
- Description 179
- Example 179
- Parameter 179
- Privilege requirement 179
- Remove backup image 179
- Syntax 179
- Command mode 180
- Description 180
- Example 180
- Firmware upgrade 180
- Parameter 180
- Privilege requirement 180
- Syntax 180
- Command mode 181
- Description 181
- Example 181
- Parameter 181
- Privilege requirement 181
- Syntax 181
- Command mode 182
- Description 182
- Example 182
- Parameter 182
- Privilege requirement 182
- Syntax 182
- Tracert 182
- Command mode 183
- Description 183
- Example 183
- Privilege requirement 183
- Show boot 183
- Show system info 183
- Syntax 183
- Command mode 184
- Description 184
- Example 184
- Parameter 184
- Privilege requirement 184
- Show running config 184
- Syntax 184
- Command mode 185
- Description 185
- Example 185
- Privilege requirement 185
- Show startup config 185
- Show system time 185
- Syntax 185
- Command mode 186
- Description 186
- Example 186
- Privilege requirement 186
- Show system time dst 186
- Show system time ntp 186
- Syntax 186
- Command mode 187
- Description 187
- Example 187
- Gigabitethernet 187
- Parameter 187
- Privilege requirement 187
- Show cable diagnostics careful interface 187
- Show cable diagnostics interface 187
- Show cable diagnostics interface gigabitethernet 187
- Syntax 187
- Command mode 188
- Example 188
- Parameter 188
- Privilege requirement 188
- Syntax 188
- Chapter 22 ipv6 address configuration commands 189
- Command mode 189
- Description 189
- Example 189
- Ipv6 address autoconfig 189
- Ipv6 enable 189
- Privilege requirement 189
- Syntax 189
- Configuration mode 190
- Description 190
- Example 190
- Ipv6 address link local 190
- Parameter 190
- Privilege requirement 190
- Syntax 190
- Configuration mode 191
- Description 191
- Example 191
- Ipv6 address dhcp 191
- Ipv6 address ra 191
- Privilege requirement 191
- Syntax 191
- Configuration mode 192
- Description 192
- Example 192
- Ipv6 address eui 64 192
- Parameter 192
- Privilege requirement 192
- Syntax 192
- Configuration mode 193
- Description 193
- Example 193
- Ipv6 address 193
- Parameter 193
- Privilege requirement 193
- Syntax 193
- Command mode 194
- Description 194
- Example 194
- Privilege requirement 194
- Show ipv6 interface 194
- Syntax 194
- Chapter 23 ethernet configuration commands 195
- Command mode 195
- Description 195
- Example 195
- Interface gigabitethernet 195
- Interface range gigabitethernet 195
- Parameter 195
- Privilege requirement 195
- Syntax 195
- Command mode 196
- Description 196
- Example 196
- Parameter 196
- Privilege requirement 196
- Syntax 196
- User guidelines 196
- Command mode 197
- Description 197
- Example 197
- Privilege requirement 197
- Shutdown 197
- Syntax 197
- Command mode 198
- Description 198
- Duplex 198
- Example 198
- Flow control 198
- Parameter 198
- Privilege requirement 198
- Syntax 198
- Command mode 199
- Description 199
- Example 199
- Parameter 199
- Privilege requirement 199
- Syntax 199
- Bandwidth 200
- Command mode 200
- Description 200
- Example 200
- Parameter 200
- Privilege requirement 200
- Storm control 200
- Syntax 200
- Clear counters 201
- Command mode 201
- Description 201
- Example 201
- Parameter 201
- Privilege requirement 201
- Syntax 201
- Command mode 202
- Description 202
- Example 202
- Privilege requirement 202
- Show interface counters 202
- Show interface status 202
- Syntax 202
- Command mode 203
- Description 203
- Example 203
- Parameter 203
- Privilege requirement 203
- Show interface configuration 203
- Show storm control 203
- Syntax 203
- Command mode 204
- Description 204
- Example 204
- Parameter 204
- Privilege requirement 204
- Show bandwidth 204
- Syntax 204
- Chapter 24 qos commands 205
- Command mode 205
- Description 205
- Example 205
- Parameter 205
- Privilege requirement 205
- Syntax 205
- User guidelines 205
- Command mode 206
- Description 206
- Example 206
- Privilege requirement 206
- Qos dscp 206
- Qos queue cos map 206
- Syntax 206
- User guidelines 206
- Command mode 207
- Description 207
- Example 207
- Parameter 207
- Privilege requirement 207
- Qos queue dscp map 207
- Syntax 207
- User guidelines 207
- Command mode 208
- Description 208
- Example 208
- Parameter 208
- Privilege requirement 208
- Qos queue mode 208
- Syntax 208
- User guidelines 208
- Command mode 209
- Description 209
- Example 209
- Parameter 209
- Privilege requirement 209
- Show qos interface 209
- Syntax 209
- Command mode 210
- Description 210
- Example 210
- Privilege requirement 210
- Show qos cos map 210
- Show qos dscp map 210
- Syntax 210
- Command mode 211
- Description 211
- Example 211
- Privilege requirement 211
- Show qos queue mode 211
- Show qos status 211
- Syntax 211
- Example 212
- Privilege requirement 212
- Chapter 25 port mirror commands 213
- Command mode 213
- Description 213
- Example 213
- Monitor session destination interface 213
- Parameter 213
- Privilege requirement 213
- Syntax 213
- Command mode 214
- Description 214
- Monitor session source interface 214
- Parameter 214
- Privilege requirement 214
- Syntax 214
- User guidelines 214
- Command mode 215
- Description 215
- Example 215
- Parameter 215
- Privilege requirement 215
- Show monitor session 215
- Syntax 215
- Chapter 26 port isolation commands 216
- Command mode 216
- Description 216
- Example 216
- Parameter 216
- Port isolation 216
- Privilege requirement 216
- Syntax 216
- Command mode 217
- Description 217
- Example 217
- Parameter 217
- Privilege requirement 217
- Show port isolation interface 217
- Syntax 217
- Chapter 27 loopback detection commands 218
- Command mode 218
- Description 218
- Example 218
- Loopback detection global 218
- Loopback detection interval 218
- Parameter 218
- Privilege requirement 218
- Syntax 218
- Command mode 219
- Description 219
- Example 219
- Loopback detection recovery time 219
- Parameter 219
- Privilege requirement 219
- Syntax 219
- Command mode 220
- Description 220
- Example 220
- Loopback detection config 220
- Loopback detection interface 220
- Parameter 220
- Privilege requirement 220
- Syntax 220
- Command mode 221
- Description 221
- Example 221
- Loopback detection recover 221
- Privilege requirement 221
- Syntax 221
- Command mode 222
- Description 222
- Example 222
- Parameter 222
- Privilege requirement 222
- Show loopback detection global 222
- Show loopback detection interface 222
- Syntax 222
- Example 223
- Privilege requirement 223
- Absolute 224
- Chapter 28 acl commands 224
- Command mode 224
- Description 224
- Example 224
- Parameter 224
- Privilege requirement 224
- Syntax 224
- Time range 224
- Command mode 225
- Description 225
- Example 225
- Parameter 225
- Periodic 225
- Privilege requirement 225
- Syntax 225
- Command mode 226
- Description 226
- Example 226
- Holiday 226
- Parameter 226
- Privilege requirement 226
- Syntax 226
- Access list create 227
- Command mode 227
- Description 227
- Example 227
- Holiday global 227
- Parameter 227
- Privilege requirement 227
- Syntax 227
- Command mode 228
- Description 228
- Example 228
- Mac access list 228
- Parameter 228
- Privilege requirement 228
- Syntax 228
- Access list standard 229
- Command mode 229
- Description 229
- Example 229
- Parameter 229
- Privilege requirement 229
- Syntax 229
- Access list extended 230
- Description 230
- Parameter 230
- Syntax 230
- Command mode 231
- Description 231
- Example 231
- Parameter 231
- Privilege requirement 231
- Syntax 231
- Access list policy name 232
- Command mode 232
- Description 232
- Example 232
- Privilege requirement 232
- Access list policy action 233
- Command mode 233
- Description 233
- Example 233
- Parameter 233
- Privilege requirement 233
- Syntax 233
- Command mode 234
- Description 234
- Example 234
- Parameter 234
- Privilege requirement 234
- Redirect interface 234
- S condition 234
- Syntax 234
- Command mode 235
- Description 235
- Example 235
- Parameter 235
- Privilege requirement 235
- S mirror 235
- Syntax 235
- Command mode 236
- Description 236
- Example 236
- Parameter 236
- Privilege requirement 236
- Qos remark 236
- Syntax 236
- Access list bind interface 237
- Access list bind vlan 237
- Command mode 237
- Description 237
- Example 237
- Parameter 237
- Privilege requirement 237
- Syntax 237
- Command mode 238
- Description 238
- Example 238
- Parameter 238
- Privilege requirement 238
- Show access list 238
- Show access list status 238
- Syntax 238
- Command mode 239
- Description 239
- Example 239
- Parameter 239
- Privilege requirement 239
- Show access list bind 239
- Show access list policy 239
- Syntax 239
- Example 240
- Chapter 29 mstp commands 241
- Command mode 241
- Description 241
- Example 241
- Privilege requirement 241
- Spanning tree global 241
- Spanning tree interface 241
- Syntax 241
- Description 242
- Example 242
- Parameter 242
- Privilege requirement 242
- Spanning tree common config 242
- Syntax 242
- Command mode 243
- Description 243
- Example 243
- Parameter 243
- Privilege requirement 243
- Spanning tree mode 243
- Syntax 243
- Command mode 244
- Description 244
- Example 244
- Instance 244
- Privilege requirement 244
- Spanning tree mst configuration 244
- Syntax 244
- Command mode 245
- Description 245
- Example 245
- Parameters 245
- Privilege requirement 245
- Syntax 245
- Command mode 246
- Description 246
- Example 246
- Parameters 246
- Privilege requirement 246
- Revision 246
- Syntax 246
- Command mode 247
- Description 247
- Example 247
- Parameter 247
- Privilege requirement 247
- Spanning tree mst 247
- Spanning tree mst instance 247
- Syntax 247
- Command mode 248
- Description 248
- Example 248
- Parameter 248
- Privilege requirement 248
- Spanning tree priority 248
- Syntax 248
- Command mode 249
- Description 249
- Example 249
- Parameter 249
- Privilege requirement 249
- Spanning tree tc defend 249
- Syntax 249
- Command mode 250
- Description 250
- Example 250
- Parameter 250
- Privilege requirement 250
- Spanning tree timer 250
- Syntax 250
- Command mode 251
- Description 251
- Example 251
- Parameter 251
- Privilege requirement 251
- Spanning tree hold count 251
- Spanning tree max hops 251
- Syntax 251
- Command mode 252
- Description 252
- Example 252
- Privilege requirement 252
- Spanning tree bpdufilter 252
- Spanning tree bpduguard 252
- Syntax 252
- Command mode 253
- Description 253
- Example 253
- Privilege requirement 253
- Spanning tree guard loop 253
- Syntax 253
- Command mode 254
- Description 254
- Example 254
- Privilege requirement 254
- Spanning tree guard root 254
- Spanning tree guard tc 254
- Syntax 254
- Command mode 255
- Description 255
- Example 255
- Privilege requirement 255
- Spanning tree mcheck 255
- Syntax 255
- Command mode 256
- Description 256
- Example 256
- Privilege requirement 256
- Show spanning tree active 256
- Show spanning tree bridge 256
- Syntax 256
- Command mode 257
- Description 257
- Example 257
- Parameter 257
- Privilege requirement 257
- Show spanning tree interface 257
- Show spanning tree interface security 257
- Syntax 257
- Command mode 258
- Description 258
- Example 258
- Parameter 258
- Privilege requirement 258
- Show spanning tree mst 258
- Syntax 258
- Chapter 30 dldp commands 260
- Command mode 260
- Description 260
- Dldp global 260
- Dldp interval 260
- Example 260
- Parameter 260
- Privilege requirement 260
- Syntax 260
- Command mode 261
- Description 261
- Dldp shut mode 261
- Example 261
- Parameter 261
- Privilege requirement 261
- Syntax 261
- Command mode 262
- Description 262
- Dldp interface 262
- Dldp reset global 262
- Example 262
- Privilege requirement 262
- Syntax 262
- Command mode 263
- Description 263
- Dldp reset interface 263
- Example 263
- Privilege requirement 263
- Show dldp 263
- Syntax 263
- Command mode 264
- Description 264
- Example 264
- Parameter 264
- Privilege requirement 264
- Show dldp interface 264
- Syntax 264
- Chapter 31 igmp snooping commands 265
- Command mode 265
- Description 265
- Example 265
- Ip igmp snooping global 265
- Ip igmp snooping interface 265
- Privilege requirement 265
- Syntax 265
- Command mode 266
- Description 266
- Example 266
- Ip igmp snooping report suppression 266
- Privilege requirement 266
- Syntax 266
- Command mode 267
- Description 267
- Example 267
- Ip igmp snooping drop unknown 267
- Ip igmp snooping immediate leave 267
- Privilege requirement 267
- Syntax 267
- Description 268
- Example 268
- Ip igmp snooping vlan config 268
- Parameter 268
- Syntax 268
- Command mode 269
- Description 269
- Example 269
- Ip igmp snooping multi vlan config 269
- Privilege requirement 269
- Syntax 269
- Command mode 270
- Example 270
- Parameter 270
- Privilege requirement 270
- Command mode 271
- Description 271
- Example 271
- Ip igmp snooping filter global 271
- Ip igmp snooping filter interface 271
- Parameter 271
- Privilege requirement 271
- Syntax 271
- Command mode 272
- Description 272
- Example 272
- Ip igmp snooping filter add id 272
- Parameter 272
- Privilege requirement 272
- Syntax 272
- Command mode 273
- Description 273
- Example 273
- Ip igmp snooping filter maxgroup 273
- Ip igmp snooping filter mode 273
- Parameter 273
- Privilege requirement 273
- Syntax 273
- Command mode 274
- Description 274
- Example 274
- Ip igmp snooping querier vlan 274
- Parameter 274
- Privilege requirement 274
- Syntax 274
- Command mode 275
- Description 275
- Example 275
- Ip igmp snooping querier vlan general query 275
- Parameter 275
- Privilege requirement 275
- Syntax 275
- Description 276
- Example 276
- Ip igmp snooping querier vlan specific query 276
- Parameter 276
- Syntax 276
- Command mode 277
- Description 277
- Example 277
- Ip igmp snooping authentication 277
- Privilege requirement 277
- Syntax 277
- User guidelines 277
- Clear ip igmp snooping statistics 278
- Command mode 278
- Description 278
- Example 278
- Ip igmp snooping accounting 278
- Privilege requirement 278
- Syntax 278
- Command mode 279
- Description 279
- Example 279
- Parameter 279
- Privilege requirement 279
- Show ip igmp snooping 279
- Show ip igmp snooping interface 279
- Syntax 279
- Command mode 280
- Description 280
- Example 280
- Parameter 280
- Privilege requirement 280
- Show ip igmp snooping multi vlan 280
- Show ip igmp snooping vlan 280
- Syntax 280
- Command mode 281
- Description 281
- Example 281
- Parameter 281
- Privilege requirement 281
- Show ip igmp snooping groups 281
- Syntax 281
- Command mode 282
- Description 282
- Example 282
- Parameter 282
- Privilege requirement 282
- Show ip igmp snooping querier 282
- Syntax 282
- Chapter 32 mld snooping commands 283
- Command mode 283
- Description 283
- Example 283
- Ipv6 mld snooping 283
- Ipv6 mld snooping router aging time 283
- Privilege requirement 283
- Syntax 283
- Command mode 284
- Description 284
- Example 284
- Ipv6 mld snooping member aging time 284
- Parameter 284
- Privilege requirement 284
- Syntax 284
- Command mode 285
- Description 285
- Example 285
- Ipv6 mld snooping report suppression 285
- Ipv6 mld snooping unknown filter 285
- Privilege requirement 285
- Syntax 285
- Command mode 286
- Description 286
- Example 286
- Ipv6 mld snooping last listener query count 286
- Ipv6 mld snooping last listener query inteval 286
- Parameter 286
- Privilege requirement 286
- Syntax 286
- Command mode 287
- Description 287
- Example 287
- Ipv6 mld snooping multicast vlan 287
- Parameter 287
- Privilege requirement 287
- Syntax 287
- Command mode 288
- Description 288
- Example 288
- Ipv6 mld snooping multicast vlan vlan id 288
- Ipv6 mld snooping vlan 288
- Parameter 288
- Privilege requirement 288
- Syntax 288
- Command mode 289
- Description 289
- Example 289
- Ipv6 mld snooping vlan router aging time 289
- Parameter 289
- Privilege requirement 289
- Syntax 289
- Command mode 290
- Description 290
- Example 290
- Ipv6 mld snooping vlan immediate leave 290
- Ipv6 mld snooping vlan member aging time 290
- Parameter 290
- Privilege requirement 290
- Syntax 290
- Command mode 291
- Description 291
- Example 291
- Ipv6 mld snooping vlan mrouter 291
- Parameter 291
- Privilege requirement 291
- Syntax 291
- Command mode 292
- Description 292
- Example 292
- Ipv6 mld snooping querier vlan 292
- Ipv6 mld snooping vlan static 292
- Parameter 292
- Privilege requirement 292
- Syntax 292
- Command mode 293
- Description 293
- Example 293
- Ipv6 mld snooping querier vlan 293
- Ipv6 mld snooping querier vlan max response time 293
- Max response time 293
- Parameter 293
- Privilege requirement 293
- Syntax 293
- Command mode 294
- Description 294
- Example 294
- Ipv6 mld snooping querier vlan query interval 294
- Ipv6 mld snooping querier vlan query source 294
- Parameter 294
- Privilege requirement 294
- Syntax 294
- Command mode 295
- Description 295
- Example 295
- Ipv6 mld snooping filter global 295
- Parameter 295
- Privilege requirement 295
- Syntax 295
- Command mode 296
- Description 296
- Example 296
- Ipv6 mld snooping filter interface 296
- Ipv6 mld snooping filter mode 296
- Privilege requirement 296
- Syntax 296
- Command mode 297
- Description 297
- Example 297
- Ipv6 mld snooping filter id 297
- Parameter 297
- Privilege requirement 297
- Syntax 297
- Clear ipv6 mld snooping statistics 298
- Command mode 298
- Description 298
- Example 298
- Ipv6 mld snooping max group 298
- Parameter 298
- Privilege requirement 298
- Syntax 298
- Command mode 299
- Description 299
- Example 299
- Parameter 299
- Privilege requirement 299
- Show ipv6 mld snooping 299
- Show ipv6 mld snooping vlan 299
- Syntax 299
- Command mode 300
- Description 300
- Example 300
- Parameter 300
- Privilege requirement 300
- Show ipv6 mld snooping group 300
- Show ipv6 mld snooping static mcast 300
- Syntax 300
- Command mode 301
- Description 301
- Example 301
- Privilege requirement 301
- Show ipv6 mld snooping filter 301
- Show ipv6 mld snooping interface 301
- Syntax 301
- Command mode 302
- Description 302
- Example 302
- Parameter 302
- Privilege requirement 302
- Show ipv6 mld snooping interface filter 302
- Show ipv6 mld snooping querier 302
- Syntax 302
- Command mode 303
- Description 303
- Example 303
- Parameter 303
- Privilege requirement 303
- Show ipv6 mld snooping statistics 303
- Syntax 303
- Chapter 33 snmp commands 304
- Command mode 304
- Description 304
- Example 304
- Privilege requirement 304
- Snmp server 304
- Snmp server view 304
- Syntax 304
- Command mode 305
- Description 305
- Example 305
- Parameter 305
- Privilege requirement 305
- Snmp server group 305
- Syntax 305
- Command mode 306
- Example 306
- Parameter 306
- Privilege requirement 306
- Description 307
- Parameter 307
- Snmp server user 307
- Syntax 307
- Command mode 308
- Description 308
- Example 308
- Parameter 308
- Privilege requirement 308
- Snmp server community 308
- Syntax 308
- Command mode 309
- Description 309
- Example 309
- Parameter 309
- Privilege requirement 309
- Snmp server host 309
- Syntax 309
- Command mode 310
- Example 310
- Privilege requirement 310
- Command mode 311
- Description 311
- Example 311
- Parameter 311
- Privilege requirement 311
- Snmp server engineid 311
- Snmp server traps snmp 311
- Syntax 311
- Command mode 312
- Description 312
- Example 312
- Parameter 312
- Privilege requirement 312
- Snmp server traps link status 312
- Syntax 312
- Command mode 313
- Description 313
- Example 313
- Parameter 313
- Privilege requirement 313
- Snmp server traps 313
- Syntax 313
- Command mode 314
- Description 314
- Example 314
- Privilege requirement 314
- Snmp server traps mac 314
- Syntax 314
- Command mode 315
- Description 315
- Example 315
- Parameter 315
- Privilege requirement 315
- Snmp server traps vlan 315
- Syntax 315
- Command mode 316
- Description 316
- Example 316
- Parameter 316
- Privilege requirement 316
- Rmon history 316
- Syntax 316
- Command mode 317
- Description 317
- Example 317
- Parameter 317
- Privilege requirement 317
- Rmon event 317
- Syntax 317
- Command mode 318
- Description 318
- Example 318
- Parameter 318
- Privilege requirement 318
- Rmon alarm 318
- Syntax 318
- Command mode 319
- Example 319
- Privilege requirement 319
- Command mode 320
- Description 320
- Example 320
- Parameter 320
- Privilege requirement 320
- Rmon statistics 320
- Show snmp server 320
- Syntax 320
- Command mode 321
- Description 321
- Example 321
- Privilege requirement 321
- Show snmp server group 321
- Show snmp server view 321
- Syntax 321
- Command mode 322
- Description 322
- Example 322
- Privilege requirement 322
- Show snmp server community 322
- Show snmp server user 322
- Syntax 322
- Command mode 323
- Description 323
- Example 323
- Privilege requirement 323
- Show snmp server engineid 323
- Show snmp server host 323
- Syntax 323
- Command mode 324
- Description 324
- Example 324
- Parameter 324
- Privilege requirement 324
- Show rmon event 324
- Show rmon history 324
- Syntax 324
- Command mode 325
- Description 325
- Example 325
- Parameter 325
- Privilege requirement 325
- Show rmon alarm 325
- Show rmon statistics 325
- Syntax 325
- Command mode 326
- Example 326
- Parameter 326
- Privilege requirement 326
- Chapter 34 lldp commands 327
- Command mode 327
- Description 327
- Example 327
- Lldp hold multiplier 327
- Privilege requirement 327
- Syntax 327
- Command mode 328
- Description 328
- Example 328
- Lldp timer 328
- Parameter 328
- Privilege requirement 328
- Syntax 328
- Command mode 329
- Description 329
- Example 329
- Lldp receive 329
- Privilege requirement 329
- Syntax 329
- Command mode 330
- Description 330
- Example 330
- Lldp snmp trap 330
- Lldp transmit 330
- Privilege requirement 330
- Syntax 330
- Command mode 331
- Description 331
- Example 331
- Lldp tlv select 331
- Privilege requirement 331
- Syntax 331
- Command mode 332
- Description 332
- Example 332
- Lldp med fast count 332
- Lldp med status 332
- Parameter 332
- Privilege requirement 332
- Syntax 332
- Command mode 333
- Description 333
- Example 333
- Lldp med tlv select 333
- Privilege requirement 333
- Syntax 333
- Command mode 334
- Description 334
- Example 334
- Lldp med location 334
- Parameter 334
- Privilege requirement 334
- Syntax 334
- Command mode 335
- Description 335
- Example 335
- Parameters 335
- Privilege requirement 335
- Show lldp 335
- Show lldp interface 335
- Syntax 335
- Command mode 336
- Description 336
- Example 336
- Parameters 336
- Privilege requirement 336
- Show lldp local information interface 336
- Show lldp neighbor information interface 336
- Syntax 336
- Command mode 337
- Description 337
- Example 337
- Parameters 337
- Privilege requirement 337
- Show lldp traffic interface 337
- Syntax 337
- Aaa enable 338
- Chapter 35 aaa commands 338
- Command mode 338
- Description 338
- Privilege requirement 338
- Syntax 338
- Command mode 339
- Description 339
- Enable admin password 339
- Example 339
- Parameter 339
- Privilege requirement 339
- Syntax 339
- Description 340
- Enable admin secret 340
- Example 340
- Parameter 340
- Syntax 340
- User guidelines 340
- Command mode 341
- Description 341
- Example 341
- Parameter 341
- Privilege requirement 341
- Syntax 341
- Tacacas server host 341
- User guidelines 341
- Command mode 342
- Description 342
- Example 342
- Privilege requirement 342
- Show tacacs server 342
- Syntax 342
- User guidelines 342
- Description 343
- Example 343
- Parameter 343
- Radius server host 343
- Syntax 343
- Command mode 344
- Description 344
- Example 344
- Privilege requirement 344
- Show radius server 344
- Syntax 344
- User guidelines 344
- Aaa group 345
- Command mode 345
- Description 345
- Example 345
- Parameter 345
- Privilege requirement 345
- Server 345
- Syntax 345
- Command mode 346
- Description 346
- Example 346
- Parameter 346
- Privilege requirement 346
- Show aaa group 346
- Syntax 346
- Aaa authentication login 347
- Command mode 347
- Description 347
- Example 347
- Parameter 347
- Privilege requirement 347
- Syntax 347
- User guidelines 347
- Aaa authentication enable 348
- Command mode 348
- Description 348
- Example 348
- Parameter 348
- Privilege requirement 348
- Syntax 348
- User guidelines 348
- Aaa accounting dot1x default 349
- Aaa authentication dot1x default 349
- Command mode 349
- Description 349
- Example 349
- Parameter 349
- Privilege requirement 349
- Syntax 349
- Command mode 350
- Description 350
- Example 350
- Parameter 350
- Privilege requirement 350
- Show aaa authentication 350
- Syntax 350
- Command mode 351
- Description 351
- Example 351
- Line console 351
- Parameter 351
- Privilege requirement 351
- Show aaa accounting 351
- Syntax 351
- Command mode 352
- Description 352
- Example 352
- Login authentication console 352
- Parameter 352
- Privilege requirement 352
- Syntax 352
- Command mode 353
- Description 353
- Enable authentication console 353
- Example 353
- Line telnet 353
- Parameter 353
- Privilege requirement 353
- Syntax 353
- Command mode 354
- Description 354
- Example 354
- Login authentication telnet 354
- Parameter 354
- Privilege requirement 354
- Syntax 354
- Command mode 355
- Description 355
- Example 355
- Line ssh 355
- Login authentication ssh 355
- Parameter 355
- Privilege requirement 355
- Syntax 355
- Command mode 356
- Description 356
- Enable authentication telnet 356
- Example 356
- Parameter 356
- Privilege requirement 356
- Syntax 356
- Command mode 357
- Description 357
- Enable authentication ssh 357
- Example 357
- Ip http login authentication 357
- Parameter 357
- Privilege requirement 357
- Syntax 357
- Command mode 358
- Description 358
- Example 358
- Ip http enable authentication 358
- Parameter 358
- Privilege requirement 358
- Syntax 358
- Command mode 359
- Description 359
- Example 359
- Privilege requirement 359
- Show aaa global 359
- Syntax 359
- Chapter 36 dhcp relay commands 360
- Command mode 360
- Description 360
- Example 360
- Ip dhcp relay 360
- Ip dhcp relay information option 360
- Privilege requirement 360
- Syntax 360
- Command mode 361
- Description 361
- Example 361
- Ip dhcp relay information strategy 361
- Parameter 361
- Privilege requirement 361
- Syntax 361
- Command mode 362
- Description 362
- Example 362
- Ip dhcp relay information circuit id 362
- Ip dhcp relay information format 362
- Parameter 362
- Privilege requirement 362
- Syntax 362
- Command mode 363
- Description 363
- Example 363
- Ip dhcp relay information remote id 363
- Parameter 363
- Privilege requirement 363
- Syntax 363
- Comman 364
- Command mode 364
- Description 364
- Example 364
- Ip dhcp relay vlan 364
- Parameter 364
- Privilege requirement 364
- Show ip dhcp relay 364
- Syntax 364
- Example 365
- Privilege requirement 365
Похожие устройства
- Tp-Link T2500G-10TS V1 Client Software_User Guide
- Tp-Link T2500G-10TS V1 Руководство пользователя
- Tp-Link T2500G-10TS V1 Руководство по быстрому старту
- Tp-Link T2600G-52TS V3 Руководство по использованию коммандной строки
- Tp-Link T2600G-52TS V3 Jetstream L2 Managed Switch_UN__Installation Guide
- Tp-Link T2600G-52TS V3 Руководство по быстрому старту
- Tp-Link T2600G-52TS V3 Rackmount Switch_EU2_12Languages__ Installation Guide
- Tp-Link T2600G-52TS V3 Rackmount Switch_America_4Languages__Installation Guide
- Tp-Link T2600G-52TS V3 Руководство пользователя
- Tp-Link T2600G-52TS V2 Client Software_User Guide
- Tp-Link T2600G-52TS V2 Руководство по использованию коммандной строки
- Tp-Link T2600G-52TS V2 Jetstream L2 Managed Switch_UN__Installation Guide
- Tp-Link T2600G-52TS V2 Rackmount Switch_America_4Languages__Installation Guide
- Tp-Link T2600G-52TS V2 Руководство по быстрому старту
- Tp-Link T2600G-52TS V2 Rackmount Switch_EU2_12Languages__ Installation Guide
- Tp-Link T2600G-52TS V2 Configuration Guide
- Tp-Link T2600G-52TS V1 Руководство по использованию коммандной строки
- Tp-Link T2600G-52TS V1 Руководство по быстрому старту
- Tp-Link T2600G-52TS V1 Rackmount Switch_EU2_12Languages__ Installation Guide
- Tp-Link T2600G-52TS V1 Руководство пользователя
Скачать
Случайные обсуждения