![Rigol DG832 [4/148] Safety requirement](/img/pdf.png)
Rigol DG832 [4/148] Safety requirement
![Rigol DG812 [4/148] Safety requirement](/views2/1472902/page4/bg4.png)
RIGOL
II DG800 User's Guide
Safety Requirement
General Safety Summary
Please review the following safety precautions carefully before putting the
instrument into operation so as to avoid any personal injury or damage to the
instrument and any product connected to it. To prevent potential hazards, please
follow the instructions specified in this manual to use the instrument properly.
Use the BNC output connector properly.
The BNC output connector on the front panel only allows to output the signal but not
to input the signal.
Use Proper Power Cord.
Only the exclusive power cord designed for the instrument and authorized for use
within the local country could be used.
Ground the Instrument.
The instrument is grounded through the Protective Earth lead of the power cord. To
avoid electric shock, connect the earth terminal of the power cord to the Protective
Earth terminal before connecting any input or output terminals.
Connect the Probe Correctly.
If a probe is used, the probe ground lead must be connected to earth ground. Do not
connect the ground lead to high voltage. Improper way of connection could result in
dangerous voltages being present on the connectors, controls or other surfaces of
the oscilloscope and probes, which will cause potential hazards for operators.
Observe All Terminal Ratings.
To avoid fire or shock hazard, observe all ratings and markers on the instrument and
check your manual for more information about ratings before connecting the
instrument.
Use Proper Overvoltage Protection.
Ensure that no overvoltage (such as that caused by a bolt of lightning) can reach the
product. Otherwise, the operator might be exposed to the danger of an electric
shock.
Do Not Operate Without Covers.
Do not operate the instrument with covers or panels removed.
Do Not Insert Objects Into the Air Outlet.
Do not insert objects into the air outlet, as doing so may cause damage to the
instrument.
Содержание
- Jul 2018 rigol suzhou technologies inc 1
- User s guide dg800 series function arbitrary waveform generator 1
- Contact us 3
- Copyright 3
- Guaranty and declaration 3
- Notices 3
- Product certification 3
- Publication number 3
- Software version 3
- Trademark information 3
- General safety summary 4
- Safety requirement 4
- Safety notices and symbols 6
- Care and cleaning 7
- Environmental considerations 7
- Dg800 series function arbitrary waveform generator overview 8
- Content conventions in this manual 9
- Document overview 9
- Format conventions in this manual 9
- Main topics in this manual 9
- Manuals of this product 10
- Contents 11
- Chapter 1 quick start 15
- Quick start 15
- General inspection 16
- Appearance and dimensions 17
- Front panel overview 18
- Rear panel overview 22
- To connect to ac power 25
- To prepare for use 25
- To set the system language 25
- Turn on checkout 25
- User interface 26
- To use the built in help system 29
- Chapter 2 front panel operations 31
- Front panel operations 31
- To output basic waveform 32
- To select output channel 32
- To select basic waveform 33
- To set frequency period 34
- To set amplitude high level 35
- 10lg 0 01 vrms dbm r w 36
- Vrms 2 2 vpp 36
- To set offset low level 37
- To set start phase 38
- To set duty cycle square 39
- To set symmetry ramp 40
- To set pulse width duty cycle pulse 41
- To set rising falling edge pulse 42
- To enable channel output 43
- Align phase 44
- Example to output sine 45
- Figure 2 3 sine waveform 46
- To enable arbitrary waveforms 47
- To output the arbitrary waveform 47
- To select the waveform 47
- Built in waveform 48
- To set parameters 52
- 2 sin 2 sin 2 sin 53
- Harmonic overview 53
- To output harmonic 53
- Φ π ϕ π ϕ π t f a t f a t f a t f 53
- To select harmonic type 54
- To set fundamental waveform parameters 54
- To set harmonic order 54
- Example to output harmonic 55
- To select harmonic amplitude 55
- To set harmonic phase 55
- Figure 2 5 harmonic 57
- To output dual tone waveform 59
- To output advanced waveform 60
- Sequence 62
- Amplitude modulation am 64
- Modulation 64
- To select am modulation 64
- To select the carrier waveform 64
- To set carrier waveform parameters 64
- To select modulation source 65
- To set modulating waveform frequency 66
- To set the modulation depth 66
- Carrier waveform suppression 67
- Frequency modulation fm 68
- To select fm modulation 68
- To select the carrier waveform 68
- To set carrier waveform parameters 68
- To select modulation source 69
- To set modulating waveform frequency 69
- To set the frequency deviation 69
- Phase modulation pm 71
- To select pm modulation 71
- To select the carrier waveform 71
- To set carrier waveform parameters 71
- To select modulation source 72
- To set modulating waveform frequency 72
- To set phase deviation 73
- Amplitude shift keying ask 74
- To select ask modulation 74
- To select the carrier waveform 74
- To set carrier waveform parameters 74
- To select modulation source 75
- To set modulating rate 75
- To set the modulation amplitude 75
- To set the modulation polarity 76
- Frequency shift keying fsk 77
- To select fsk modulation 77
- To select the carrier waveform 77
- To set carrier waveform parameters 77
- To select modulation source 78
- To set hop frequency 78
- To set modulating rate 78
- To set the modulation polarity 79
- Phase shift keying psk 80
- To select psk modulation 80
- To select the carrier waveform 80
- To set carrier waveform parameters 80
- To select modulation source 81
- To set modulating phase 81
- To set modulating rate 81
- To set modulation polarity 82
- Pulse width modulation pwm 83
- To select pwm modulation 83
- To select the carrier waveform 83
- To set carrier waveform parameters 83
- To select modulation source 84
- To set modulating waveform frequency 84
- To set width duty deviation 85
- Linear sweep 86
- Sweep type 86
- To enable the sweep function 86
- Log sweep 87
- Step sweep 87
- Return time 88
- Sweep time 88
- Center frequency and frequency span 89
- Start frequency and stop frequency 89
- Sweep trigger source 90
- Marker freq 91
- Start hold 92
- Stop hold 92
- Burst type 93
- N cycle 93
- To enable the burst function 93
- Infinite burst 94
- Burst delay 95
- Gated burst 95
- Burst period 96
- Idle level 96
- Burst trigger source 97
- Gated polarity 98
- Frequency counter 99
- To enable the frequency counter 99
- To set the frequency counter 100
- Storage system 103
- Store and recall 103
- Categories 104
- File type 104
- File operation 105
- Copy and paste 107
- Delete 108
- Seamless interconnection with oscilloscope 109
- Channel setting 111
- Output setting 111
- Sync setting 113
- Coupling setting 115
- Frequency coupling 115
- Amplitude coupling 116
- Phase coupling 116
- Trigger coupling 117
- Track mode 118
- Waveform combination 119
- Common settings 120
- Power on 120
- System setting 120
- To set the system language 120
- Beeper 121
- Clock source 121
- Decimal point 121
- Delimiter 122
- Interface 122
- System log 122
- To set the gpib address 122
- Ip configuration 123
- Network status 123
- To set the lan parameters 123
- To set the subnet mask 124
- Visa address 124
- Default settings 125
- To set default gateway 125
- To set dns 125
- Display setting 126
- Option 126
- System info 126
- Print setting 127
- System utility function 128
- To restore preset 128
- Channel copy 132
- To install the option 133
- To lock the keyboard 135
- Chapter 3 remote control 137
- Remote control 137
- Remote control via lan 138
- Remote control via usb 138
- Remote control via gpib 140
- Chapter 4 troubleshooting 143
- Troubleshooting 143
- Appendix 145
- Appendix a accessories and options 145
- Chapter 5 appendix 145
- Description order no 145
- Option 145
- Optional accessories 145
- Standard accessories 145
- Appendix b warranty 146
- Visa address 2 94 waveform combination 2 89 width deviation 2 55 148
Похожие устройства
- Rigol DG952 Инструкция по эксплуатации(ENG)
- Rigol DG972 Инструкция по эксплуатации(ENG)
- Rigol DG992 Инструкция по эксплуатации(ENG)
- Rigol DL3021 Инструкция по эксплуатации(ENG)
- Rigol DL3021A Инструкция по эксплуатации(ENG)
- Rigol DL3031 Инструкция по эксплуатации(ENG)
- Rigol DL3031A Инструкция по эксплуатации(ENG)
- Rigol RSA3030 Инструкция по эксплуатации(ENG)
- Rigol RSA3030-TG Инструкция по эксплуатации(ENG)
- Rigol RSA3045 Инструкция по эксплуатации(ENG)
- Rigol RSA3045-TG Инструкция по эксплуатации(ENG)
- Rigol DS7014 Инструкция по эксплуатации(ENG)
- Rigol DS7024 Инструкция по эксплуатации(ENG)
- Rigol DS7034 Инструкция по эксплуатации(ENG)
- Rigol DS7054 Инструкция по эксплуатации(ENG)
- Rigol MSO7014 Инструкция по эксплуатации(ENG)
- Rigol MSO7024 Инструкция по эксплуатации(ENG)
- Rigol MSO7034 Инструкция по эксплуатации(ENG)
- Rigol MSO7054 Инструкция по эксплуатации(ENG)
- Rigol RSA5032 Инструкция по эксплуатации(ENG)