![Gigabyte GA-8I945GMH-RH [11/88] English](/img/pdf.png)
Gigabyte GA-8I945GMH-RH [11/88] English
![Gigabyte GA-8I945GMH-RH [11/88] English](/views2/1047836/page11/bgb.png)
Hardware Installation- 11 -
English
Rear Panel I/O 1 PS/2 keyboard port
1 PS/2 mouse port
1 parallel port
1 SPDIF Out port
1 SPDIF In port
1 VGA port
4 USB 2.0/1.1 ports
1 1394 port
1 RJ-45 port (LAN)
6 audio jacks (Line In / Line Out / MIC In / Surround Speaker Out (Rear
Speaker Out) / Center/Subwoofer Speaker Out / Side Speaker Out)
I/O Control IT8712 chip
Hardware Monitor System voltage detection
CPU temperature detection
CPU / System fan speed detection
CPU warning temperature
CPU / System fan failure warning
CPU smart fan control
BIOS 1 4M bit flash ROM
Use of licensed AWARD BIOS
Additional Features Supports @BIOS
Supports Download Center
Supports Q-Flash
Supports EasyTune
(Note 4)
Supports Xpress Install
Supports Xpress Recovery2
Supports Xpress Rescue
Bundle Software Norton Internet Security (OEM revision)
Form Factor Mirco ATX form factor; 24.4cm x 24.4cm
(Note 1) For further CPU support information, please go to GIGABYTE's website.
(Note 2) Due to standard PC architecture, a certain amount of memory is reserved for system usage
andtherefore the actual memory size is less than the stated amount.
For example, 4 GB of memory size will instead be shown as 3.xxGB memory during system
startup.
(Note 3) To use a DDRII 667 memory module on the motherboard, you must install an 800/1066MHz
FSB processor .
(Note 4) EasyTune functions may vary depending on different motherboards.
Содержание
- D pentiu 1
- Ga 8i945gmh rh 1
- Lga775 processor motherboard 1
- Pentiu 1
- Processor extreme edition inte 1
- Rev 1001 12me 945gmhr 1001r 1
- User s manual 1
- Copyright 3
- Notice 3
- Product manual classification 3
- Block diagram 7 4
- Chapter 1 hardware installation 9 4
- Chapter 2 bios setup 29 4
- Ga 8i945gmh rh motherboard layout 6 4
- Table of contents 4
- Chapter 3 install drivers 49 5
- Chapter 4 appendix 53 5
- Ga 8i945gmh rh 6
- Ga 8i945gmh rh motherboard layout 6
- Block diagram 7
- 1 considerations prior to installation 9
- Chapter 1 hardware installation 9
- English 9
- Installation notices 9
- Instances of non warranty 9
- Preparing your computer 9
- 2 feature summary 10
- English 10
- English 11
- 3 1 installation of the cpu 12
- 3 installation of the cpu and heatsink 12
- English 12
- 3 2 installation of the heatsink 13
- English 13
- 4 installation of memory 14
- English 14
- Dual channel ddr ii 15
- English 15
- 5 install expansion cards 16
- English 16
- 6 i o back panel introduction 17
- English 17
- Ieee 1394 port 17
- Lan port 17
- Line in 17
- Line out front speaker out 17
- Lpt parallel port 17
- Mic in 17
- Ps 2 keyboard and ps 2 mouse connector 17
- Spdif_i 17
- Spdif_o 17
- Usb port 17
- Vga port 17
- 7 connectors introduction 18
- Center subwoofer speaker out 18
- English 18
- Rear speaker out 18
- Side speaker out 18
- 2 atx_12v atx power connector 19
- English 19
- Hardware installation 19 19
- With the use of the power connector the power supply can supply enough stable power to all the components on the motherboard before connecting the power connector please make sure that all components and devices are properly installed align the power connector with its proper location on the motherboard and connect tightly the atx_12v power connector mainly supplies power to the cpu if the atx_12v power connector is not connected the system will not start caution please use a power supply that is able to handle the system voltage requirements it is recommended that a power supply that can withstand high power consumption be used 300w or greater if a power supply is used that does not provide the required power the result can lead to an unstable system or a system that is unable to start if you use a 24 pin atx power supply please remove the small cover on the power connector on the motherboard before plugging in the power cord otherwise please do not remove it 19
- 4 cpu_fan sys_fan cooler fan power connector 20
- English 20
- Fdd floppy connector 20
- An ide device connects to the computer via an ide connector one ide connector can connect to one ide cable and the single ide cable can then connect to two ide devices hard drive or optical drive if you wish to connect two ide devices please set the jumper on one ide device as master and the other as slave for information on settings please refer to the instructions located on the ide device 21
- English 21
- Hardware installation 21 21
- Ide ide connector 21
- Sata 3gb s can provide up to 300mb s transfer rate please refer to the bios setting for the serial ata and install the proper driver in order to work properly 21
- Sataii0 sataii1 sataii2 sataii3 sata 3gb s connector 21
- English 22
- F_panel front panel jumper 22
- Ga 8i945gmh rh motherboard 22 22
- Please connect the power led pc speaker reset switch and power switch etc of your chassis frontpanel to the f_panel connector according to the pin assignment below 22
- By default the audio driver is configured to support hd audio to connect an ac97 front panel audio module to this connector please refer to the instructions on page 77 about the software settings 23
- English 23
- F_audio front audio connector 23
- Hardware installation 23 23
- Pwr_led 23
- Pwr_led is connect with the system power indicator to indicate whether the system is on off it will blink when the system enters suspend mode 23
- This connector supports either hd high definition or ac97 front panel audio module if you wish to use the front audio function connect the front panel audio module to this connector check the pin assignments carefully while you connect the front panel audio module incorrect connection between the module and connector will make the audio device unable to work or even damage it for optional front panel audio module please contact your chassis manufacturer 23
- Be careful with the polarity of the front usb connector check the pin assignments carefully while you connect the front usb cable incorrect connection between the cable and connector will make the device unable to work or even damage it for optional front usb cable please contact your local dealer 24
- Cd_in cd in 24
- Connect cd rom or dvd rom audio out to the connector 24
- English 24
- F_ usb f_usb2 front usb connector 24
- Ga 8i945gmh rh motherboard 24 24
- Be careful with the polarity of the com connector check the pin assignment carefully while you connect the com cable incorrect connection between the cable and connector will make the device unable to work or even damage it for optional com cable please contact your local dealer 25
- Coma serial port connector 25
- English 25
- F1_1394 f2_1394 ieee 1394 connector 25
- Hardware installation 25 25
- Serial interface standard set by institute of electrical and electronics engineers which has features like high speed highbandwidth and hot plug be careful with the polarity of the ieee1394 connector check the pin assignment carefully while you connect the ieee1394 cable incorrect connection between the cable and connector will make the device unable to work or even damage it for optional ieee1394 cable please contact your local dealer 25
- Ci chassis intrusion case open 26
- Clr_cmos clear cmos 26
- English 26
- Bat battery 27
- English 27
- Hardware installation 27 27
- English 28
- Chapter 2 bios setup 29
- Control keys 29
- English 29
- Main menu 29
- Status page setup menu option page setup menu 29
- English 30
- For boot menu 30
- Ga 8i945gmh rh motherboard 30 30
- If you can t find the setting you want please press ctrl f1 to search the advanced option hidden please load optimized defaults in the bios when somehow the system works not stable as usual this action makes the system reset to the default for stability the bios setup menus described in this chapter are for reference only and may differ from the exact settings for your motherboard 30
- Select boot sequence for onboard or add on cards device 30
- The main menu for example bios ver f1 30
- To accept or enter the sub menu 30
- To exit this menu 30
- English 31
- 1 standard cmos features 32
- Access mode use this to set the access mode for the hard drive the four options are chs lba large auto default auto hard drive information should be labeled on the outside drive casing enter the appropriate option based on this information 32
- Cylinder number of cylinders 32
- Day the day from 1 to 31 or the maximum allowed in the month 32
- English 32
- Ga 8i945gmh rh motherboard 32 32
- Head number of heads 32
- Ide channel 0 master slave 32
- Ide hdd auto detection press enter to select this option for automatic device detection ide channel 0 master slave ide device setup you can use one of three methods auto allows bios to automatically detect ide devices during post default none select this if no ide devices are used and the system will skip the automatic detection step and allow for faster system start up manual user can manually input the correct settings 32
- Month the month jan through dec 32
- Precomp write precomp 32
- The time is calculated base on the 24 hour military time clock for example 1 p m is 13 00 00 32
- Week the week from sun to sat determined by the bios and is display only 32
- Year the year from 1999 through 2098 32
- Base memory 33
- Drive a drive b 33
- English 33
- Extended memory 33
- Floppy 3 mode support for japan area 33
- Halt on 33
- Memory 33
- 2 advanced bios features 34
- Cdrom select your boot device priority by cdrom 34
- Disabled disabled this function 34
- English 34
- First second third boot device 34
- Floppy select your boot device priority by floppy 34
- Ga 8i945gmh rh motherboard 34 34
- Hard disk boot priority 34
- Hard disk select your boot device priority by hard disk 34
- Lan select your boot device priority by lan 34
- Ls120 select your boot device priority by ls120 34
- Note this item will show up when you install a processor which supports this function 34
- Password check 34
- Pentiu 34
- Processor with ht technology 34
- Select boot sequence for onboard or add on cards scsi raid etc 34
- Setup the system will boot but will not access to setup page if the correct password is not entered at the prompt default value 34
- System the system will not boot and will not access to setup page if the correct password is not entered at the prompt 34
- System will detect automatically and show up when you install the inte 34
- To exit this menu 34
- Usb cdrom select your boot device priority by usb cdrom 34
- Usb fdd select your boot device priority by usb fdd 34
- Usb hdd select your boot device priority by usb hdd 34
- Usb zip select your boot device priority by usb zip 34
- Zip select your boot device priority by zip 34
- Cpu eist functio 35
- Cpu enhanced halt c1e 35
- Cpu hyper threading 35
- Cpu thermal monitor 2 tm2 35
- English 35
- Limit cpuid max to 3 35
- No execute memory protec 35
- On chip frame buffer size 35
- 3 integrated peripherals 36
- Ahci set the onboard sata controller to ahci mode advanced host controller interface ahci is an interface specification that allows the storage driver to enable advanced serial ata features such as native command queuing and hot plug for more details about ahci please visit intel s website 36
- Auto bios will auto detect default value combined set on chip sata mode to combined you can use up to 4 hdds on the motherboard 2 for sata and the other for pata ide 36
- Ch master slave set pata ide to ch 0 master slave 36
- Ch master slave set pata ide to ch 1 master slave default value 36
- Disabled disable onboard 1st channel ide port 36
- Disabled disable this function 36
- Disabled set the onboard sata controller to ide mode default value 36
- Enabled enable onboard 1st channel ide port default value 36
- English 36
- Enhanced set on chip sata mode to enhanced the motherboard allows up to 6 hdds to use 36
- Ga 8i945gmh rh motherboard 36 36
- Non combined set on chip sata mode to non combined sata will be simulated to pata mode 36
- On chip primary pci ide 36
- On chip sata mode 36
- Pata ide set to 36
- Raid set the onboard sata controller to raid mode 36
- Sata port 0 2 set to 36
- Sata raid ahci mode 36
- This value will auto make by the setting on chip sata mode and pata ide set to if pata ide were set to ch 1 master slave this function will auto set to ch 0 master slave 36
- Azalia codec 37
- English 37
- Legacy usb storage detect 37
- Onboard h w 1394 37
- Onboard h w lan 37
- Onboard lan boot rom 37
- Onboard serial port 1 37
- Sata port 1 3 set to 37
- Usb 2 controller 37
- Usb controller 37
- Usb keyboard support 37
- Usb mouse support 37
- Ecp mode use dma 38
- English 38
- Onboard parallel port 38
- Parallel port mode 38
- 4 power management setup 39
- Acpi suspend type 39
- Bios setup 39 39
- Date of month alarm everyday 1 31 39
- Delay 4 sec press power button 4 sec to power off enter suspend if button is pressed less than 4 sec 39
- Disabled disable power on by ring function 39
- Disabled disable this function 39
- Disabled disable this function default value 39
- Enabled enable alarm function to power on system if rtc alarm lead to power on is enabled 39
- Enabled enable pme event wake up default value 39
- Enabled enable power on by ring function default value 39
- Enabled enable quick resume technology 39
- English 39
- Instant off press power button then power off instantly default value 39
- Pme event wake up 39
- Power on by ring 39
- Quick resume technology 39
- Resume by alarm 39
- S1 pos set acpi suspend type to s1 pos power on suspend default value 39
- S3 str set acpi suspend type to s3 str suspend to ram 39
- Soft off by pwr bttn 39
- Time hh mm ss alarm 0 23 0 59 0 59 39
- You can set resume by alarm item to enabled and key in data time to power on system 39
- 5 pnp pci configurations 40
- Ac back function 40
- English 40
- Kb power on password 40
- Pci 1 irq assignment 40
- Pci 2 irq assignment 40
- Power on by keyboard 40
- Power on by mouse 40
- 6 pc health status 41
- Bios setup 41 41
- Case opened 41
- Cpu system fan fail warning 41
- Cpu warning temperature 41
- Current cpu system fan speed rpm 41
- Current cpu temperature 41
- Current voltage v vcore ddrv 3 v 12v 41
- Detect cpu system fan speed status automatically 41
- Detect cpu temperature automatically 41
- Detect system s voltage status automatically 41
- Disabled disable this function default value 41
- Disabled don t reset case open status default value 41
- Disabled fan warning function disable default value 41
- Enabled clear case open status at next boot 41
- Enabled fan warning function enable 41
- English 41
- F monitor cpu temperature at 6 41
- F monitor cpu temperature at 7 41
- F monitor cpu temperature at 8 41
- F monitor cpu temperature at 9 41
- If the case is closed case opened will show no if the case have been opened case opened will show yes if you want to reset case opened value set reset case open status to enabled and save cmos your computer will restart 41
- Reset case open status 41
- Cpu smart fan control 42
- Cpu smart fan mode 42
- English 42
- 7 frequency voltage control 43
- Cpu clock ratio 43
- English 43
- Memory frequency mhz 43
- Normal cpu vcore 43
- System memory multiplier 43
- 8 load fail safe defaults 44
- 9 load optimized defaults 44
- English 44
- Fail safe defaults contain the most appropriate values of the system parameters that allow minimum system performance 44
- Ga 8i945gmh rh motherboard 44 44
- Selecting this field loads the factory defaults for bios and chipset features which the system automatically detects 44
- 10 set supervisor user password 45
- Bios setup 45 45
- English 45
- When you are prompted to enter password a message password disabled will appear to confirm the password being disabled once the password is disabled the system will boot and you can enter setup freely the bios setup program allows you to specify two separate passwords supervisor password and a user password when disabled anyone may access all bios setup program function when enabled the supervisor password is required for entering the bios setup program and having full configuration fields the user password is required to access only basic items if you select system at password check in advance bios features menu you will be prompted for the password every time the system is rebooted or any time you try to enter setup menu if you select setup at password check in advance bios features menu you will be prompted only when you try to enter setup 45
- 11 save exit setup 46
- 12 exit without saving 46
- English 46
- Ga 8i945gmh rh motherboard 46 46
- Type y will quit the setup utility and save the user setup value to rtc cmos type n will return to setup utility 46
- Type y will quit the setup utility without saving to rtc cmos type n will return to setup utility 46
- English 47
- English 48
- 1 install chipset drivers 49
- Chapter 3 install drivers 49
- English 49
- 2 software applications 50
- 3 driver cd information 50
- English 50
- 4 hardware information 51
- 5 contact us 51
- English 51
- English 52
- 1 unique software utilities 53
- C i a cpu intelligent accelerator 2 53
- C o m corporate online management 53
- Chapter 4 appendix 53
- Download center 53
- English 53
- M i b memory intelligent booster 2 53
- M i t motherboard intelligent tweaker 53
- S o s system overclock saver 53
- U plus d p s universal plus dual power system 53
- 1 1 easytune 5 introduction 54
- English 54
- User interface overview 54
- 1 2 xpress recovery2 introduction 55
- Boot from cd dvd 55
- English 55
- How to use the xpress recovery2 55
- System requirements 55
- Xpress recovery2 55
- Backup 56
- English 56
- Limitations 56
- Precautions 56
- Reboot 56
- Remove 56
- Restore 56
- The main screen of xpress recovery2 56
- 1 3 flash bios method introduction 57
- Before you begin 57
- English 57
- Method 1 q flas 57
- Part one 57
- Updating bios with q flas 57
- Utility 57
- Utility on dual bios motherboards 57
- Action bar 58
- Contains the names of eight tasks and two item showing information about the bios rom type blocking a task and pressing enter key on your keyboard to enable execution of the task 58
- Contains the names of four actions needed to operate the q flash dual bios utility pressing the buttons mentioned on your keyboards to perform these actions 58
- Contains the names of four tasks blocking a task and pressing enter key on your keyboard to enable execu tion of the task 58
- Dual bios 58
- Dual bios utility bar 58
- Dual bios utility screen 58
- English 58
- Entering the q flas 58
- Exploring the q flas 58
- Ga 8i945gmf motherboard 58 58
- Q flas 58
- Step 2 press f8 button on your keyboard and then y button to enter the dual bios q flash utility 58
- Step1 to use q flash utility you must press del in the boot screen to enter bios menu 58
- Task menu for 58
- Task menu for dual bios utility 58
- Task menu for q flash utility 58
- The q flash dual bios utility screen consists of the following key components 58
- Utility 58
- Utility title 58
- After bios file is read you ll see a confirmation dialog box asking you are you sure to update bios 59
- After pressing enter you ll then see the progress of reading the bios file from the floppy disk 59
- Appendix 59 59
- Bios file in the floppy 59
- Do not trun off power or 59
- English 59
- If you want to save the current bios for backup purpose you can begin step 1 with save main bios to floppy item 59
- In this example we only download one bios file to the floppy disk so only one bios file 59
- Knxpu fba is listed 59
- Move to the bios file you want to flash and press enter 59
- Please confirm again you have the correct bios file for your motherboard 59
- Press arrow buttons on your keyboard to move the light bar to load main bios from floppy item in the q flash menu and press enter button later you will see a box pop up showing the bios files you previously downloaded to the floppy disk 59
- Reset your system at this 59
- This section tells you how to update bios using the q flash utility as described in the before you begin section above you must prepare a floppy disk having the bios file for your motherboard and insert it to your computer if you have already put the floppy disk into your system and have entered the q flash utility please follow the steps below to flash bios 59
- Using the q flas 59
- Utility 59
- After system reboots you may find the bios version on your boot screen becomes the one you flashed 60
- Becomes fab after 60
- Bios too 60
- English 60
- Ga 8i945gmf motherboard 60 60
- Please do not take out the floppy disk when it begins flashing bios 60
- Press any keys to return to the q flash menu when the bios updating procedure is completed 60
- Press esc and then y button to exit the q flash utility the computer will restart automatically after you exit q flash 60
- Press y button on your keyboard after you are sure to update bios then it will begin to update bios the progress of updating bios will be displayed 60
- The bios file 60
- To flash the backup 60
- Updating 60
- You can repeat step 1 to 60
- Appendix 61 61
- English 61
- Part two updating bios with q flas 61
- Press del to enter bios menu after system reboots when you are in bios menu move to load fail safe defaults item and press enter to load bios fail safe defaults normally the system redetects all devices after bios has been upgraded therefore we highly recommend reloading the bios defaults after bios has been upgraded 61
- Press y on your keyboard to load defaults 61
- Press y on your keyboard to save and exit 61
- Select save exit setup item to save the settings to cmos and exit the bios menu system will reboot after you exit the bios menu the procedure is completed 61
- This part guides users of single bios motherboards how to update bios using the q flas 61
- Utility 61
- Utility on single bios motherboards 61
- Action bar 62
- After bios file is read you ll see a confirmation dialog box asking you are you sure to update bios 62
- Bios file in the floppy disk 62
- Contains the names of four actions needed to operate the q flash utility pressing the buttons mentioned on your keyboards to perform these actions 62
- Contains the names of three tasks blocking a task and pressing enter key on your keyboard to enable execution of the task 62
- Do not trun off power or reset your system at 62
- English 62
- Exploring the q flas 62
- Ga 8i945gmf motherboard 62 62
- If you want to save the current bios for backup purpose you can begin step 1 with save bios to floppy item 62
- Move to the bios file you want to flash and press enter in this example we only download one bios file to the floppy disk so only one bios file 8ge800 f4 is listed 62
- Please confirm again you have the correct bios file for your motherboard 62
- Please do not take out the floppy disk when it begins flashing bios 62
- Press arrow buttons on your keyboard to move the light bar to update bios from floppy item in the q flash menu and press enter button later you will see a box pop up showing the bios files you previously downloaded to the floppy disk 62
- Q flas 62
- Task menu for 62
- Task menu for q flash utility 62
- The q flashbios utility screen consists of the following key components 62
- This section tells you how to update bios using the q flash utility as described in the before you begin section above you must prepare a floppy disk having the bios file for your motherboard and insert it to your computer if you have already put the floppy disk into your system and have entered the q flash utility please follow the steps below to flash bios 62
- This stage 62
- Using the q flas 62
- Utility 62
- Utility bar 62
- Utility screen 62
- After system reboots you may find the bios version on your boot screen becomes the one you flashed 63
- Appendix 63 63
- Congratulation you have updated bios successfully 63
- Do not trun off power or 63
- English 63
- Press any keys to return to the q flash menu when the bios updating procedure is completed 63
- Press del to enter bios menu after system reboots and load bios fail safe defaults see how to load bios fail safe defaults please kindly refer to step 6 to 7 in part one 63
- Press esc and then y button to exit the q flash utility the computer will restart automatically after you exit q flash 63
- Press y button on your keyboard after you are sure to update bios then it will begin to update bios the progress of updating bios will be shown at the same time 63
- Reset your system at this stage 63
- The bios file becomes f4 after updating 63
- English 64
- Method 2 bio 64
- Methods and steps 64
- Utility 64
- English 65
- 1 4 configuring sata hard drive s controller intel ich7 dh 66
- 1 install sata hard drive s in your system 2 configure sata controller mode and boot sequence in bios setup 3 configure raid set in raid bios 4 make a floppy disk containing the sata controller driver 66
- 1 installing sata hard drive s in your computer 66
- 5 install the sata controller driver during os installation 66
- Before you begin 66
- English 66
- To configure sata hard drive s follow the steps below 66
- 2 configuring sata controller mode and boot sequence in bios setup 67
- Appendix 67 67
- English 67
- Figure 1 67
- Step 1 turn on your computer and press del to enter bios setup during post power on self test if you want to create raid set sata raid ahci mode under the integrated peripherals menu to raid disabled by default then set on chip sata mode to manual or auto default based on your own requirements 67
- The bios setup menus described in this section may not show the exact settings for your motherboard the actual bios setup menu options you will see shall depend on the motherboard you have and the bios version 67
- You have to make sure whether the sata controller is configured correctly in system bios setup and set bios boot sequence for the sata hard drive s 67
- English 68
- Figure 2 68
- Figure 3 68
- Ga 8i945gmh rh motherboard 68 68
- Step 2 later select hard disk boot priority under the advanced bios features menu in the hard disk boot priority submenu select the model of the sata hard drive onto which you intent to install microsoft windows 2000 xp figure 2 68
- Step 3 set first boot device under the advanced bios features menu to cd rom to boot from cd rom after system restarts figure 3 68
- Step 4 save and exit bios setup 68
- 3 configuring raid set in raid bios 69
- Appendix 69 69
- English 69
- Enter the raid bios setup utility to configure a raid array skip this step and proceed to section 4 if you do not want to create raid 69
- Figure 4 69
- Figure 5 69
- Step 2 after you press ctrl i the create raid volume screen will appear figure 5 create raid volume g if you want to create raid array select create raid volume in main menu and press enter 69
- To enter configuration utility figure 4 press ctrl i to enter the raid bios setup utility 69
- English 70
- Figure 6 70
- Figure 7 70
- Ga 8i945gmh rh motherboard 70 70
- Step 3 after entering the create volume menu screen name the disk array with 1 16 letters letters cannot be special characters under the name item when finished press enter to select a raid level figure 6 there are four raid levels raid0 raid1 raid10 and raid5 select a raid level and press enter 70
- Step 4 set the stripe block size figure 7 the kb is the standard unit of stripe block size the stripe block size can be set from 4kb to 128kb after the setting press enter to set array capacity 70
- Appendix 71 71
- English 71
- Figure 8 71
- Figure 9 71
- Step 5 after setting all the items above select create volume and press enter figure 8 to begin the creation of the raid array 71
- Step 6 when prompted to confirm whether to create this volume press y to create or n to cancel 71
- After the creation is completed you can see detailed information about the raid array in the disk volume information section including raid mode disk block size disk name and disk capacity etc 72
- Delete raid volume if you want to delete a raid volume select the delete raid volume option in main menu press enter and follow on screen instructions 72
- English 72
- Figure 10 72
- Ga 8i945gmh rh motherboard 72 72
- Now you can proceed to the installation of the sata driver and operating system 72
- To exit the ich7r raid bios utility press esc in main menu 72
- 4 making a sata driver disk 73
- English 73
- 5 installing sata controller driver during os installation 74
- English 74
- English 75
- After the sata controller driver installation is completed you should see a screen as below it indicates that you have installed the sata controller driver successfully you can proceed with the windows 2000 xp installation 76
- English 76
- Figure 19 76
- Ga 8i945gmh rh motherboard 76 76
- Note each time you add a new hard drive to a raid array the raid driver will have to be installed under windows once for that hard drive after that the driver will not have to be installed 76
- 1 5 2 4 6 8 channel audio function introduction 77
- English 77
- Stereo speakers connection and settings 77
- Channel audio setup 78
- English 78
- Channel audio setup 79
- English 79
- English 80
- 2 troubleshooting 81
- English 81
- English 82
- English 83
- English 84
- English 85
- English 86
- Appendix 87 87
- Contact us 87
- English 87
- English 88
- Ga 8i945gmh rh motherboard 88 88
Похожие устройства
- Toshiba 26 DV703 R Инструкция по эксплуатации
- BBK LT4217HD Инструкция по эксплуатации
- Ballu BPDA-12C Инструкция по эксплуатации
- Apple iPhone 4 8GB Black Инструкция по эксплуатации
- Gigabyte GA-8I945GZME-RH Инструкция по эксплуатации
- Toshiba 32 AV704 R Инструкция по эксплуатации
- Bork HF SUL 1420 SI Инструкция по эксплуатации
- Ballu BPDA-09C Инструкция по эксплуатации
- Gigabyte GA-8I945GMF-RH Инструкция по эксплуатации
- Apple iPhone 4 8GB White Инструкция по эксплуатации
- Toshiba 32 AV703 R Инструкция по эксплуатации
- Panasonic NR-B53M1 Инструкция по эксплуатации
- Ballu MPA-09ER Инструкция по эксплуатации
- Gigabyte GA-8I945GME Инструкция по эксплуатации
- JVC HR-XVS30ER Инструкция по эксплуатации
- Toshiba 32 RV733 R Инструкция по эксплуатации
- Ballu AC-N006R Инструкция по эксплуатации
- Gigabyte GA-8I945GMBX Инструкция по эксплуатации
- Toshiba 32 DV703 R Инструкция по эксплуатации
- Ballu AC-T009R Инструкция по эксплуатации
Скачать
Случайные обсуждения