Home
Главная
Telwin
Зарядное Устройство
DIGITRONY 230 START
Инструкция по эксплуатации Страница: 3

Telwin DIGITRONY 230 START Инструкция по эксплуатации онлайн [3/72] 413815

- 3 -

For very at or sulphated batteries TEST mode is not

available.

9- Display for showing the selected parameter. The

display also shows a number of abbreviations relating

to the present status/mode (FIG. C).

5. OPERATION

BEFORECHARGING

NB:Beforechargingcheckthatthecapacityofthe

battery(Ah)whichistobecharged,isnotinferiorto

thatreportedonthedatatable.(Cmin).

Followtheinstructions,takinggreatcaretorespect

theordergivenbelow.

- Remove the caps of the battery charger (if foreseen)

so as to let the gas produced go out.

- Check that the level of the electrolyte covers the plates

of the battery. If these were not covered add distilled

water and cover them up to 5-10 mm.

WARNING: USE THE MAXIMUM CAUTION

DURING THIS OPERATION AS THE

ELECTROLYTE IS A HIGHLY CORROSIVE

ACID.

- Please remember that the exact charge status of the

battery can only be determined by using a densimeter

which allows measurement of the specic gravity of

the electrolyte the following indicate approximate

density values for the solute (Kg/l at 20°c):

1.28 = charged battery;

1.21 = half-charged battery;

1.14 = at battery.

- With the power supply cable disconnected from the

mains socket connect the load terminals according to

the rated voltage of the battery being charged or else

position the 12 / 24 switch (if present) according to the

battery being charged.

- Position the switch/es for adjusting the type of charge

(if present) as required (FIG.D: LOW normal charging,

HIGH rapid charging).

- Check the polarities of the battery terminals: positive

for the + symbol and negative for the - symbol.

NOTE: if the symbols are indistinguishable remember

that the positive terminal is the one not connected to

the vehicle chassis.

- Connect the red charge clamp to the positive terminal

of the battery ( + symbol).

- Connect the black charge clamp to the vehicle chassis,

at a safe distance from the battery and the fuel pipe.

NOTE: if the battery is not installed in the vehicle,

connect the clamp directly to the negative terminal of

the battery (- symbol).

- Power the battery charger by inserting the power cable

in the mains outlet and turning the main switch ON.

- Check the battery voltage and make sure that the

settings on the battery charger panel are compatible

with the specications of the battery being charged.

These checks should be carried out with the

corresponding key in ”Test” mode.

CHARGING

- Press the corresponding key to switch to “CHARGE”

mode

- Monitor the battery voltage and charge current

parameters on the display using the V / I key

(FIG.B-7).

- The value shown on the display as parameter “I” shows

the battery charge current (in amps): during this phase

it will be observed that the value slowly decreases

to very low values depending on the capacity and

condition of the battery (Fig.B-9),

- The battery voltage can be constantly monitored on

the display as parameter “ V “.

NOTE: Once the battery is charged you may note the

liquid inside the battery starting to “boil”. It is advisable to

stop charging when this phenomenon appears so as to

prevent damage to the battery.

AUTOMATICCHARGING

Press the corresponding key to pass to “TRONIC” mode

During this phase the battery charger will constantly

monitor the voltage over the battery terminals,

automatically supplying or cutting off the charge current

to the battery as necessary.

Also in this case it is possible to monitor the battery

voltage and charge current on the display using the V

/ I key.

The charge current can be set as illustrated. When it is

cut off the display will show the message “END”.

WARNING:SEALEDBATTERIES(GEL,AGM)

Ifitisnecessarytochargethistypeofbattery

takegreatcare.Chargeslowlykeepinganeye

on the voltage over the battery terminals.

Whenthisvoltage,availableasparameter“V”onthe

display, reaches 14.4V for 12V batteries (28.8V for

24Vbatteries)werecommendyoustopcharging.

Formodelswhereforeseen,itisadvisabletosetthe

automaticfunction“TRONIC”.

Simultaneouschargingofseveralbatteries(FIG.E)

This operation must be performed with great caution:

WARNING; do not simultaneously charge different types

of batteries or batteries with different capacities or levels

of discharge.

If you have to charge more than one battery at the same

time you can connect them “in series” or “in parallel”. Of

the two systems, we recommend connecting the batteries

in series because in this way it is possible to monitor the

current circulating in each battery, which will be the same

as that shown by the ” I ” parameter on the display.

NOTE: If two batteries with rated voltages of 12V are

connected in series, the corresponding button must set

the battery charger to 24V.

ENDOFCHARGING

- Press the corresponding key to switch to “TEST”

mode.

- Remove the power supply from the battery charger by

turning the switch to OFF (if present) and/or removing

the power supply cable from the mains outlet.

- Disconnect the black charge clamp from the chassis of

the vehicle or from the negative terminal of the battery

(- symbol).

- Disconnect the red charge clamp from the positive

terminal of the battery (+ symbol).

- Store the battery charger in a dry place.

- Close up the battery cells with the appropriate plugs (if

present).

STARTING

Before starting the vehicle, make sure the battery

is connected properly to the respective (+ and

-) terminals, and that it is in good condition (not

sulphatedordud).

Never ever start vehicles with the batteries

disconnected from their respective terminals; the

presenceofthebatteryisessentialfortheelimination

ofpossibleovervoltagethatmaybegenerateddueto

energyaccumulatingintheconnectioncablesatthe

startingstage.

For starting turn the switch to the starting position

corresponding to the voltage of the vehicle. n this mode

the display will show only and exclusively “Str”.

FIG.B

Before turning the starter key, it is essential to make a

rapid charge of 5-10 minutes, which will make starting

much easier.

Rapid charging should always be done with the

batterychargerswitchedtothechargepositionand

NOTtostarting.

Telwin DIGITRONY 230 START Инструкция по эксплуатации онлайн [3/72] 413815

Содержание

Похожие устройства