Alpicair AWI/AWO-26HPDC1 [4/5] Operating the remote controller
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Alpicair AWI/AWO-26HPDC1 [4/5] Operating the remote controller

Alpicair AWI/AWO-26HPDC1 [4/5] Operating the remote controller
2
5
1. If the AUTO mode is not comfortable , you may manually override
the settings by using COOL, DRY, HEAT( HEAT PUMP units only),
or FAN ONLY modes.
2. Push the or button to set the desired room temperature.
When in COOLING mode, the most comfortable settings are 21 C
or above. When in HEATING mode, the most comfortable settings
are 28 C or below.
3. Push the button to select the FAN mode of AUTO, HIGH,
MED or LOW.
4. Push the button. The operation lamp lights and the air
conditioner starts to operate per your settings. Push the
button again to stop this unit operation.
Fan
On/off
On/off
The FAN ONLY mode cannot be used to control the temperature. While
in this mode, only steps 1 3 and 4 may be performed.
COOL , HEAT, and FAN ONLY Operation
NOTE
Due to the difference of the set temperature of the unit and the
actual indoor temperature, the Air Conditioner when in DRY mode
will automatically operate many times without running the COOL
and FAN mode.
1. Push the button to select DRY.
2. Push the or button to set the desired temperature from
21 C to 28 C.
3. Push the button. The operation lamp lights and the air
conditioner starts to operate in the DRY mode. Push the
button again to stop this unit operation.
Mode
On/off
On/off
DRY OPERATION
NOTE
Push Timer on/off button to set the on and off times of the unit. The
effective operation time set by the remote controller for the timer function
is limited to a period of between 0.5 and less than 24 hours.
TIMER OPERATION
1. To set the STARTING time.
Button : Push the button to decrease the indoor temperature
setting to 17 .
Mode Button: Each time you press the button, a mode is
selected in a sequence that goes from AUTO COOL DRY
HEAT and FAN only as the following figure indicates:
Swing Button: Press the SWING button to activate the swing
feature. Push the button again to stop.
NOTE: HEAT only for Heat Pump
AUTO
COOL
DRY
HEAT
FAN
Fan Button: This button is used for selecting Fan Speed. Each time
you press the button, a fan speed is selected in a sequence
that goes from AUTO LOW MED to HIGH, then back to Auto.
When you select the AUTO or DRY mode, the fan speed will be
automatically controlled and you can not set the fan speed.
Button : Push the button to increase the indoor temperature
setting to 30 .
1
2
3
4
5
6
7
8
9
On/off Button: Push this button to start the unit operation. Push
the button again to stop the unit operation.
Air direction Button: Press this button to change the swing
angle of the louver. The swing angle of the louver is 6 C for
each press. When the louver swing at a certain angle which
would affect the cooling and heating effect of the air conditioner,
it would automatically change the swing direction . No symbol
will appear in the display area when press this button.
o
Timer on Button: Press this button to initiate the auto-on time
sequence. Each press will increase the auto-timed setting in 30
minutes increments. When the setting time displays 10Hr, each
press will increase the auto-timed setting 60 minutes increments.
To cancel the auto-timed program, continue pressing the button
until nothing displays.
Sleep/Turbo Button: Press this button to select SLEEP or TURBO
mode. Each time you press the button, the operation mode is shifted in
the direction of the arrow. When the operation mode is either DRY or
FAN only, this function can not be used.
1.1 Push the button, then the remote controller shows
, the last set time for the starting operation and the
signal " " will be shown on the Timer display area. You
are now ready to reset the time to START the operation.
1.2 Push the button again to set desired unit start time.
1.3 After setting the ,there will be a one-half second
delay before the remote controller transmits the signal to
the air conditioner.
Timer on
ON TIMER
Hr
Timer on
Timer on
SLEEP
SLEEP OFF
TURBO
TURBO OFF
10
Timer off Button: Press this button to initiate the auto-off time
sequence. Each press will increase the auto-timed setting in 30
minutes increments. When the setting time displays 10Hr, each
press will increase the auto-timed setting 60 minutes increments.
To cancel the auto-timed program, continue pressing the button
until nothing displays.
1
3
4
5
6
7
8
9
10
2
5
1. If the AUTO mode is not comfortable , you may manually override
the settings by using COOL, DRY, HEAT( HEAT PUMP units only),
or FAN ONLY modes.
2. Push the or button to set the desired room temperature.
When in COOLING mode, the most comfortable settings are 21 C
or above. When in HEATING mode, the most comfortable settings
are 28 C or below.
3. Push the button to select the FAN mode of AUTO, HIGH,
MED or LOW.
4. Push the button. The operation lamp lights and the air
conditioner starts to operate per your settings. Push the
button again to stop this unit operation.
Fan
On/off
On/off
The FAN ONLY mode cannot be used to control the temperature. While
in this mode, only steps 1 3 and 4 may be performed.
COOL , HEAT, and FAN ONLY Operation
NOTE
Due to the difference of the set temperature of the unit and the
actual indoor temperature, the Air Conditioner when in DRY mode
will automatically operate many times without running the COOL
and FAN mode.
1. Push the button to select DRY.
2. Push the or button to set the desired temperature from
21 C to 28 C.
3. Push the button. The operation lamp lights and the air
conditioner starts to operate in the DRY mode. Push the
button again to stop this unit operation.
Mode
On/off
On/off
DRY OPERATION
NOTE
Push Timer on/off button to set the on and off times of the unit. The
effective operation time set by the remote controller for the timer function
is limited to a period of between 0.5 and less than 24 hours.
TIMER OPERATION
1. To set the STARTING time.
Button : Push the button to decrease the indoor temperature
setting to 17 .
Mode Button: Each time you press the button, a mode is
selected in a sequence that goes from AUTO COOL DRY
HEAT and FAN only as the following figure indicates:
Swing Button: Press the SWING button to activate the swing
feature. Push the button again to stop.
NOTE: HEAT only for Heat Pump
AUTO
COOL
DRY
HEAT
FAN
Fan Button: This button is used for selecting Fan Speed. Each time
you press the button, a fan speed is selected in a sequence
that goes from AUTO LOW MED to HIGH, then back to Auto.
When you select the AUTO or DRY mode, the fan speed will be
automatically controlled and you can not set the fan speed.
Button : Push the button to increase the indoor temperature
setting to 30 .
1
2
3
4
5
6
7
8
9
On/off Button: Push this button to start the unit operation. Push
the button again to stop the unit operation.
Air direction Button: Press this button to change the swing
angle of the louver. The swing angle of the louver is 6 C for
each press. When the louver swing at a certain angle which
would affect the cooling and heating effect of the air conditioner,
it would automatically change the swing direction . No symbol
will appear in the display area when press this button.
o
Timer on Button: Press this button to initiate the auto-on time
sequence. Each press will increase the auto-timed setting in 30
minutes increments. When the setting time displays 10Hr, each
press will increase the auto-timed setting 60 minutes increments.
To cancel the auto-timed program, continue pressing the button
until nothing displays.
Sleep/Turbo Button: Press this button to select SLEEP or TURBO
mode. Each time you press the button, the operation mode is shifted in
the direction of the arrow. When the operation mode is either DRY or
FAN only, this function can not be used.
1.1 Push the button, then the remote controller shows
, the last set time for the starting operation and the
signal " " will be shown on the Timer display area. You
are now ready to reset the time to START the operation.
1.2 Push the button again to set desired unit start time.
1.3 After setting the ,there will be a one-half second
delay before the remote controller transmits the signal to
the air conditioner.
Timer on
ON TIMER
Hr
Timer on
Timer on
SLEEP
SLEEP OFF
TURBO
TURBO OFF
10
Timer off Button: Press this button to initiate the auto-off time
sequence. Each press will increase the auto-timed setting in 30
minutes increments. When the setting time displays 10Hr, each
press will increase the auto-timed setting 60 minutes increments.
To cancel the auto-timed program, continue pressing the button
until nothing displays.
2
5
1. If the AUTO mode is not comfortable , you may manually override
the settings by using COOL, DRY, HEAT( HEAT PUMP units only),
or FAN ONLY modes.
2. Push the or button to set the desired room temperature.
When in COOLING mode, the most comfortable settings are 21 C
or above. When in HEATING mode, the most comfortable settings
are 28 C or below.
3. Push the button to select the FAN mode of AUTO, HIGH,
MED or LOW.
4. Push the button. The operation lamp lights and the air
conditioner starts to operate per your settings. Push the
button again to stop this unit operation.
Fan
On/off
On/off
The FAN ONLY mode cannot be used to control the temperature. While
in this mode, only steps 1 3 and 4 may be performed.
COOL , HEAT, and FAN ONLY Operation
NOTE
Due to the difference of the set temperature of the unit and the
actual indoor temperature, the Air Conditioner when in DRY mode
will automatically operate many times without running the COOL
and FAN mode.
1. Push the button to select DRY.
2. Push the or button to set the desired temperature from
21 C to 28 C.
3. Push the button. The operation lamp lights and the air
conditioner starts to operate in the DRY mode. Push the
button again to stop this unit operation.
Mode
On/off
On/off
DRY OPERATION
NOTE
Push Timer on/off button to set the on and off times of the unit. The
effective operation time set by the remote controller for the timer function
is limited to a period of between 0.5 and less than 24 hours.
TIMER OPERATION
1. To set the STARTING time.
Button : Push the button to decrease the indoor temperature
setting to 17 .
Mode Button: Each time you press the button, a mode is
selected in a sequence that goes from AUTO COOL DRY
HEAT and FAN only as the following figure indicates:
Swing Button: Press the SWING button to activate the swing
feature. Push the button again to stop.
NOTE: HEAT only for Heat Pump
AUTO
COOL
DRY
HEAT
FAN
Fan Button: This button is used for selecting Fan Speed. Each time
you press the button, a fan speed is selected in a sequence
that goes from AUTO LOW MED to HIGH, then back to Auto.
When you select the AUTO or DRY mode, the fan speed will be
automatically controlled and you can not set the fan speed.
Button : Push the button to increase the indoor temperature
setting to 30 .
1
2
3
4
5
6
7
8
9
On/off Button: Push this button to start the unit operation. Push
the button again to stop the unit operation.
Air direction Button: Press this button to change the swing
angle of the louver. The swing angle of the louver is 6 C for
each press. When the louver swing at a certain angle which
would affect the cooling and heating effect of the air conditioner,
it would automatically change the swing direction . No symbol
will appear in the display area when press this button.
o
Timer on Button: Press this button to initiate the auto-on time
sequence. Each press will increase the auto-timed setting in 30
minutes increments. When the setting time displays 10Hr, each
press will increase the auto-timed setting 60 minutes increments.
To cancel the auto-timed program, continue pressing the button
until nothing displays.
Sleep/Turbo Button: Press this button to select SLEEP or TURBO
mode. Each time you press the button, the operation mode is shifted in
the direction of the arrow. When the operation mode is either DRY or
FAN only, this function can not be used.
1.1 Push the button, then the remote controller shows
, the last set time for the starting operation and the
signal " " will be shown on the Timer display area. You
are now ready to reset the time to START the operation.
1.2 Push the button again to set desired unit start time.
1.3 After setting the ,there will be a one-half second
delay before the remote controller transmits the signal to
the air conditioner.
Timer on
ON TIMER
Hr
Timer on
Timer on
SLEEP
SLEEP OFF
TURBO
TURBO OFF
10
Timer off Button: Press this button to initiate the auto-off time
sequence. Each press will increase the auto-timed setting in 30
minutes increments. When the setting time displays 10Hr, each
press will increase the auto-timed setting 60 minutes increments.
To cancel the auto-timed program, continue pressing the button
until nothing displays.
2
5
1. If the AUTO mode is not comfortable , you may manually override
the settings by using COOL, DRY, HEAT( HEAT PUMP units only),
or FAN ONLY modes.
2. Push the or button to set the desired room temperature.
When in COOLING mode, the most comfortable settings are 21 C
or above. When in HEATING mode, the most comfortable settings
are 28 C or below.
3. Push the button to select the FAN mode of AUTO, HIGH,
MED or LOW.
4. Push the button. The operation lamp lights and the air
conditioner starts to operate per your settings. Push the
button again to stop this unit operation.
Fan
On/off
On/off
The FAN ONLY mode cannot be used to control the temperature. While
in this mode, only steps 1 3 and 4 may be performed.
COOL , HEAT, and FAN ONLY Operation
NOTE
Due to the difference of the set temperature of the unit and the
actual indoor temperature, the Air Conditioner when in DRY mode
will automatically operate many times without running the COOL
and FAN mode.
1. Push the button to select DRY.
2. Push the or button to set the desired temperature from
21 C to 28 C.
3. Push the button. The operation lamp lights and the air
conditioner starts to operate in the DRY mode. Push the
button again to stop this unit operation.
Mode
On/off
On/off
DRY OPERATION
NOTE
Push Timer on/off button to set the on and off times of the unit. The
effective operation time set by the remote controller for the timer function
is limited to a period of between 0.5 and less than 24 hours.
TIMER OPERATION
1. To set the STARTING time.
Button : Push the button to decrease the indoor temperature
setting to 17 .
Mode Button: Each time you press the button, a mode is
selected in a sequence that goes from AUTO COOL DRY
HEAT and FAN only as the following figure indicates:
Swing Button: Press the SWING button to activate the swing
feature. Push the button again to stop.
NOTE: HEAT only for Heat Pump
AUTO
COOL
DRY
HEAT
FAN
Fan Button: This button is used for selecting Fan Speed. Each time
you press the button, a fan speed is selected in a sequence
that goes from AUTO LOW MED to HIGH, then back to Auto.
When you select the AUTO or DRY mode, the fan speed will be
automatically controlled and you can not set the fan speed.
Button : Push the button to increase the indoor temperature
setting to 30 .
1
2
3
4
5
6
7
8
9
On/off Button: Push this button to start the unit operation. Push
the button again to stop the unit operation.
Air direction Button: Press this button to change the swing
angle of the louver. The swing angle of the louver is 6 C for
each press. When the louver swing at a certain angle which
would affect the cooling and heating effect of the air conditioner,
it would automatically change the swing direction . No symbol
will appear in the display area when press this button.
o
Timer on Button: Press this button to initiate the auto-on time
sequence. Each press will increase the auto-timed setting in 30
minutes increments. When the setting time displays 10Hr, each
press will increase the auto-timed setting 60 minutes increments.
To cancel the auto-timed program, continue pressing the button
until nothing displays.
Sleep/Turbo Button: Press this button to select SLEEP or TURBO
mode. Each time you press the button, the operation mode is shifted in
the direction of the arrow. When the operation mode is either DRY or
FAN only, this function can not be used.
1.1 Push the button, then the remote controller shows
, the last set time for the starting operation and the
signal " " will be shown on the Timer display area. You
are now ready to reset the time to START the operation.
1.2 Push the button again to set desired unit start time.
1.3 After setting the ,there will be a one-half second
delay before the remote controller transmits the signal to
the air conditioner.
Timer on
ON TIMER
Hr
Timer on
Timer on
SLEEP
SLEEP OFF
TURBO
TURBO OFF
10
Timer off Button: Press this button to initiate the auto-off time
sequence. Each press will increase the auto-timed setting in 30
minutes increments. When the setting time displays 10Hr, each
press will increase the auto-timed setting 60 minutes increments.
To cancel the auto-timed program, continue pressing the button
until nothing displays.
2
5
1. If the AUTO mode is not comfortable , you may manually override
the settings by using COOL, DRY, HEAT( HEAT PUMP units only),
or FAN ONLY modes.
2. Push the or button to set the desired room temperature.
When in COOLING mode, the most comfortable settings are 21 C
or above. When in HEATING mode, the most comfortable settings
are 28 C or below.
3. Push the button to select the FAN mode of AUTO, HIGH,
MED or LOW.
4. Push the button. The operation lamp lights and the air
conditioner starts to operate per your settings. Push the
button again to stop this unit operation.
Fan
On/off
On/off
The FAN ONLY mode cannot be used to control the temperature. While
in this mode, only steps 1 3 and 4 may be performed.
COOL , HEAT, and FAN ONLY Operation
NOTE
Due to the difference of the set temperature of the unit and the
actual indoor temperature, the Air Conditioner when in DRY mode
will automatically operate many times without running the COOL
and FAN mode.
1. Push the button to select DRY.
2. Push the or button to set the desired temperature from
21 C to 28 C.
3. Push the button. The operation lamp lights and the air
conditioner starts to operate in the DRY mode. Push the
button again to stop this unit operation.
Mode
On/off
On/off
DRY OPERATION
NOTE
Push Timer on/off button to set the on and off times of the unit. The
effective operation time set by the remote controller for the timer function
is limited to a period of between 0.5 and less than 24 hours.
TIMER OPERATION
1. To set the STARTING time.
Button : Push the button to decrease the indoor temperature
setting to 17 .
Mode Button: Each time you press the button, a mode is
selected in a sequence that goes from AUTO COOL DRY
HEAT and FAN only as the following figure indicates:
Swing Button: Press the SWING button to activate the swing
feature. Push the button again to stop.
NOTE: HEAT only for Heat Pump
AUTO
COOL
DRY
HEAT
FAN
Fan Button: This button is used for selecting Fan Speed. Each time
you press the button, a fan speed is selected in a sequence
that goes from AUTO LOW MED to HIGH, then back to Auto.
When you select the AUTO or DRY mode, the fan speed will be
automatically controlled and you can not set the fan speed.
Button : Push the button to increase the indoor temperature
setting to 30 .
1
2
3
4
5
6
7
8
9
On/off Button: Push this button to start the unit operation. Push
the button again to stop the unit operation.
Air direction Button: Press this button to change the swing
angle of the louver. The swing angle of the louver is 6 C for
each press. When the louver swing at a certain angle which
would affect the cooling and heating effect of the air conditioner,
it would automatically change the swing direction . No symbol
will appear in the display area when press this button.
o
Timer on Button: Press this button to initiate the auto-on time
sequence. Each press will increase the auto-timed setting in 30
minutes increments. When the setting time displays 10Hr, each
press will increase the auto-timed setting 60 minutes increments.
To cancel the auto-timed program, continue pressing the button
until nothing displays.
Sleep/Turbo Button: Press this button to select SLEEP or TURBO
mode. Each time you press the button, the operation mode is shifted in
the direction of the arrow. When the operation mode is either DRY or
FAN only, this function can not be used.
1.1 Push the button, then the remote controller shows
, the last set time for the starting operation and the
signal " " will be shown on the Timer display area. You
are now ready to reset the time to START the operation.
1.2 Push the button again to set desired unit start time.
1.3 After setting the ,there will be a one-half second
delay before the remote controller transmits the signal to
the air conditioner.
Timer on
ON TIMER
Hr
Timer on
Timer on
SLEEP
SLEEP OFF
TURBO
TURBO OFF
10
Timer off Button: Press this button to initiate the auto-off time
sequence. Each press will increase the auto-timed setting in 30
minutes increments. When the setting time displays 10Hr, each
press will increase the auto-timed setting 60 minutes increments.
To cancel the auto-timed program, continue pressing the button
until nothing displays.
2
ВЫКЛ
ВЫКЛ
TEMP Button : Push this button to decrease the indoor
temperature setting.
RESET Button: When you press the recessed RESET button,
all current settings are cancelled and the control will return to
the initial settings.
SLEEP Button: Press this button to go into the Energy-Saving
operation mode. Press it again to cancel. This function is only
can be used on COOL, HEAT and AUTO mode and maintain the
most comfortable temperature for you.
2
NOTE: COOL only model has no HEAT feature.
!
1
6
ON/OFF Button: Push this button to start operation, push the
button again to stop operation.
9
TEMP Button : Push this button to increase the indoor
temperature setting .
2
AIR DIRECTION Button: Press this button to change the swing
angle of the louver. The swing angle of the louver is 6 for
each press. When the louver swing at a certain angle which
would affect the cooling and heating effect of the air conditioner,
it would automatically change the swing direction . No symbol
will appear in the display area when press this button. (Not
applicable to units without this function).
o
MODE Selection Button: Each time the button is pressed, the
operation mode is shifted in the direction of the arrow:
AUTO
COOL
DRY
HEAT
FAN
3
FAN SPEED Button: Used to select the Fan Speed in four steps-
AUTO LOW MED or HIGH. Each time the button is pressed,
the fan speed mode is shifted.
8
TIMER ON Button: Press this button to initiate the auto-on time
sequence. Each press will increase the auto-timed setting in 30
minutes increments. When the setting time displays 10:00, each
press will increase the auto-timed setting 60 minutes increments.
To cancel the auto-timed program, simply adjust the auto-on time
to 0:00.
10
11
4
5
NOTE: While the unit is running under SLEEP operation
mode, it would be canceled if you press the other button.
!
1
Model
Transmission Distance
Lowest Voltage of CPU
Emitting Signal
Rated Voltage
R51M/(C)E, R51M/BG(C)E, RG51M2/(C)E,
RG51A/(C)E, RG51M3/(C)E.
-5 C 60 C
8m (when using 3.0 voltage,
it Gets 11m)
3.0V(Alkaline dry batteries LR03 2)
2.0V
~
Remote Controller Specification
Performance Features
Features of the Remote controller buttons
1. Operating Mode: AUTO COOL DRY
HEAT(Cooling only model without) and FAN .
2. Timer Setting Function in 24 hours.
3. Indoor Setting Temperature Range : 17 C~30 C.
4. Full function of LCD (Liquid Crystal Display)
5. Back light emitting(only available for R51M/BG(C)E models)
Fig. 1
( C)
TEMP
AUTO
COOL
DRY
HEAT
FAN
HIGH
MED
LOW
MODE
FAN SPEED
TIMER ON
SLEEP
ON/OFF
TIMER OFF
AIR
DIRECTION
RESET LOCK
1
2
4
5
6
7
3
8
9
10
11
12
13
14
Environment
SET TEMPERATURE
SWING
LED
DISPLAY
TURBO
SWING Button: Push this switch button to activate auto
swing feature of the horizontal louver. Push it again to stop.
LED DISPLAY Button: Press this button to clear the digit
display in the air conditioner, press it again to activate it (Not
available for the units without LED display window).
7
*
*
*
*
*
*
*
*
NOTE:
: Indicates optional
button.
M odels RG51M2/(C)E:
without 14 and 15
buttons.
Models RG51M3/(C)E:
without 7 , 14 and
15 buttons.
Models R51M/(C)E
and R51M/BG(C)E:
without 15 button.
CLEAN
AIR
15
*
*
TEMP Button : Push this button to decrease the indoor
temperature setting.
RESET Button: When you press the recessed RESET button,
all current settings are cancelled and the control will return to
the initial settings.
SLEEP Button: Press this button to go into the Energy-Saving
operation mode. Press it again to cancel. This function is only
can be used on COOL, HEAT and AUTO mode and maintain the
most comfortable temperature for you.
2
NOTE: COOL only model has no HEAT feature.
!
1
6
ON/OFF Button: Push this button to start operation, push the
button again to stop operation.
9
TEMP Button : Push this button to increase the indoor
temperature setting .
2
AIR DIRECTION Button: Press this button to change the swing
angle of the louver. The swing angle of the louver is 6 for
each press. When the louver swing at a certain angle which
would affect the cooling and heating effect of the air conditioner,
it would automatically change the swing direction . No symbol
will appear in the display area when press this button. (Not
applicable to units without this function).
o
MODE Selection Button: Each time the button is pressed, the
operation mode is shifted in the direction of the arrow:
AUTO
COOL
DRY
HEAT
FAN
3
FAN SPEED Button: Used to select the Fan Speed in four steps-
AUTO LOW MED or HIGH. Each time the button is pressed,
the fan speed mode is shifted.
8
TIMER ON Button: Press this button to initiate the auto-on time
sequence. Each press will increase the auto-timed setting in 30
minutes increments. When the setting time displays 10:00, each
press will increase the auto-timed setting 60 minutes increments.
To cancel the auto-timed program, simply adjust the auto-on time
to 0:00.
10
11
4
5
NOTE: While the unit is running under SLEEP operation
mode, it would be canceled if you press the other button.
!
1
Model
Transmission Distance
Lowest Voltage of CPU
Emitting Signal
Rated Voltage
R51M/(C)E, R51M/BG(C)E, RG51M2/(C)E,
RG51A/(C)E, RG51M3/(C)E.
-5 C 60 C
8m (when using 3.0 voltage,
it Gets 11m)
3.0V(Alkaline dry batteries LR03 2)
2.0V
~
Remote Controller Specification
Performance Features
Features of the Remote controller buttons
1. Operating Mode: AUTO COOL DRY
HEAT(Cooling only model without) and FAN .
2. Timer Setting Function in 24 hours.
3. Indoor Setting Temperature Range : 17 C~30 C.
4. Full function of LCD (Liquid Crystal Display)
5. Back light emitting(only available for R51M/BG(C)E models)
Fig. 1
( C)
TEMP
AUTO
COOL
DRY
HEAT
FAN
HIGH
MED
LOW
MODE
FAN SPEED
TIMER ON
SLEEP
ON/OFF
TIMER OFF
AIR
DIRECTION
RESET LOCK
1
2
4
5
6
7
3
8
9
10
11
12
13
14
Environment
SET TEMPERATURE
SWING
LED
DISPLAY
TURBO
SWING Button: Push this switch button to activate auto
swing feature of the horizontal louver. Push it again to stop.
LED DISPLAY Button: Press this button to clear the digit
display in the air conditioner, press it again to activate it (Not
available for the units without LED display window).
7
*
*
*
*
*
*
*
*
NOTE:
: Indicates optional
button.
M odels RG51M2/(C)E:
without 14 and 15
buttons.
Models RG51M3/(C)E:
without 7 , 14 and
15 buttons.
Models R51M/(C)E
and R51M/BG(C)E:
without 15 button.
CLEAN
AIR
15
*
*
TEMP Button : Push this button to decrease the indoor
temperature setting.
RESET Button: When you press the recessed RESET button,
all current settings are cancelled and the control will return to
the initial settings.
SLEEP Button: Press this button to go into the Energy-Saving
operation mode. Press it again to cancel. This function is only
can be used on COOL, HEAT and AUTO mode and maintain the
most comfortable temperature for you.
2
NOTE: COOL only model has no HEAT feature.
!
1
6
ON/OFF Button: Push this button to start operation, push the
button again to stop operation.
9
TEMP Button : Push this button to increase the indoor
temperature setting .
2
AIR DIRECTION Button: Press this button to change the swing
angle of the louver. The swing angle of the louver is 6 for
each press. When the louver swing at a certain angle which
would affect the cooling and heating effect of the air conditioner,
it would automatically change the swing direction . No symbol
will appear in the display area when press this button. (Not
applicable to units without this function).
o
MODE Selection Button: Each time the button is pressed, the
operation mode is shifted in the direction of the arrow:
AUTO
COOL
DRY
HEAT
FAN
3
FAN SPEED Button: Used to select the Fan Speed in four steps-
AUTO LOW MED or HIGH. Each time the button is pressed,
the fan speed mode is shifted.
8
TIMER ON Button: Press this button to initiate the auto-on time
sequence. Each press will increase the auto-timed setting in 30
minutes increments. When the setting time displays 10:00, each
press will increase the auto-timed setting 60 minutes increments.
To cancel the auto-timed program, simply adjust the auto-on time
to 0:00.
10
11
4
5
NOTE: While the unit is running under SLEEP operation
mode, it would be canceled if you press the other button.
!
1
Model
Transmission Distance
Lowest Voltage of CPU
Emitting Signal
Rated Voltage
R51M/(C)E, R51M/BG(C)E, RG51M2/(C)E,
RG51A/(C)E, RG51M3/(C)E.
-5 C 60 C
8m (when using 3.0 voltage,
it Gets 11m)
3.0V(Alkaline dry batteries LR03 2)
2.0V
~
Remote Controller Specification
Performance Features
Features of the Remote controller buttons
1. Operating Mode: AUTO COOL DRY
HEAT(Cooling only model without) and FAN .
2. Timer Setting Function in 24 hours.
3. Indoor Setting Temperature Range : 17 C~30 C.
4. Full function of LCD (Liquid Crystal Display)
5. Back light emitting(only available for R51M/BG(C)E models)
Fig. 1
( C)
TEMP
AUTO
COOL
DRY
HEAT
FAN
HIGH
MED
LOW
MODE
FAN SPEED
TIMER ON
SLEEP
ON/OFF
TIMER OFF
AIR
DIRECTION
RESET LOCK
1
2
4
5
6
7
3
8
9
10
11
12
13
14
Environment
SET TEMPERATURE
SWING
LED
DISPLAY
TURBO
SWING Button: Push this switch button to activate auto
swing feature of the horizontal louver. Push it again to stop.
LED DISPLAY Button: Press this button to clear the digit
display in the air conditioner, press it again to activate it (Not
available for the units without LED display window).
7
*
*
*
*
*
*
*
*
NOTE:
: Indicates optional
button.
M odels RG51M2/(C)E:
without 14 and 15
buttons.
Models RG51M3/(C)E:
without 7 , 14 and
15 buttons.
Models R51M/(C)E
and R51M/BG(C)E:
without 15 button.
CLEAN
AIR
15
*
*
TEMP Button : Push this button to decrease the indoor
temperature setting.
RESET Button: When you press the recessed RESET button,
all current settings are cancelled and the control will return to
the initial settings.
SLEEP Button: Press this button to go into the Energy-Saving
operation mode. Press it again to cancel. This function is only
can be used on COOL, HEAT and AUTO mode and maintain the
most comfortable temperature for you.
2
NOTE: COOL only model has no HEAT feature.
!
1
6
ON/OFF Button: Push this button to start operation, push the
button again to stop operation.
9
TEMP Button : Push this button to increase the indoor
temperature setting .
2
AIR DIRECTION Button: Press this button to change the swing
angle of the louver. The swing angle of the louver is 6 for
each press. When the louver swing at a certain angle which
would affect the cooling and heating effect of the air conditioner,
it would automatically change the swing direction . No symbol
will appear in the display area when press this button. (Not
applicable to units without this function).
o
MODE Selection Button: Each time the button is pressed, the
operation mode is shifted in the direction of the arrow:
AUTO
COOL
DRY
HEAT
FAN
3
FAN SPEED Button: Used to select the Fan Speed in four steps-
AUTO LOW MED or HIGH. Each time the button is pressed,
the fan speed mode is shifted.
8
TIMER ON Button: Press this button to initiate the auto-on time
sequence. Each press will increase the auto-timed setting in 30
minutes increments. When the setting time displays 10:00, each
press will increase the auto-timed setting 60 minutes increments.
To cancel the auto-timed program, simply adjust the auto-on time
to 0:00.
10
11
4
5
NOTE: While the unit is running under SLEEP operation
mode, it would be canceled if you press the other button.
!
1
Model
Transmission Distance
Lowest Voltage of CPU
Emitting Signal
Rated Voltage
R51M/(C)E, R51M/BG(C)E, RG51M2/(C)E,
RG51A/(C)E, RG51M3/(C)E.
-5 C 60 C
8m (when using 3.0 voltage,
it Gets 11m)
3.0V(Alkaline dry batteries LR03 2)
2.0V
~
Remote Controller Specification
Performance Features
Features of the Remote controller buttons
1. Operating Mode: AUTO COOL DRY
HEAT(Cooling only model without) and FAN .
2. Timer Setting Function in 24 hours.
3. Indoor Setting Temperature Range : 17 C~30 C.
4. Full function of LCD (Liquid Crystal Display)
5. Back light emitting(only available for R51M/BG(C)E models)
Fig. 1
( C)
TEMP
AUTO
COOL
DRY
HEAT
FAN
HIGH
MED
LOW
MODE
FAN SPEED
TIMER ON
SLEEP
ON/OFF
TIMER OFF
AIR
DIRECTION
RESET LOCK
1
2
4
5
6
7
3
8
9
10
11
12
13
14
Environment
SET TEMPERATURE
SWING
LED
DISPLAY
TURBO
SWING Button: Push this switch button to activate auto
swing feature of the horizontal louver. Push it again to stop.
LED DISPLAY Button: Press this button to clear the digit
display in the air conditioner, press it again to activate it (Not
available for the units without LED display window).
7
*
*
*
*
*
*
*
*
NOTE:
: Indicates optional
button.
M odels RG51M2/(C)E:
without 14 and 15
buttons.
Models RG51M3/(C)E:
without 7 , 14 and
15 buttons.
Models R51M/(C)E
and R51M/BG(C)E:
without 15 button.
CLEAN
AIR
15
*
*
Кнопка ON/OFF: Кнопка включения кондиционера. Повторное нажатие
выключает кондиционер.
Кнопка Mode: С каждым нажатием кнопки включается следующий режим
в такой последовательности: AUTO, COOL (охлаждение), DRY (осушение),
HEAT (отопление), FAN (вентиляция) и снова AUTO.
ПРИМЕЧАНИЕ: Режим HEAT только у теплового насоса.
Кнопка Эта кнопка повышает установленную для помещения
температуру до 30 ºС.
Кнопка Эта кнопка снижает установленную для помещения
температуру до 17 ºС.
Кнопка FAN: Кнопка выбора скорости вентилятора. С каждым нажатием
кнопки включается следующий режим скорости вентилятора в такой
последовательности: AUTO, LOW (низкая), MED (средняя), HIGH
(высокая) и опять AUTO. В режимах работы AUTO и DRY частота
вращения вентилятора устанавливается автоматически, и ее нельзя
изменить.
Кнопка Sleep/Turbo: Кнопка включения режимов SLEEP и TURBO.
При каждом нажатии этой кнопки режим работы переключается по
направлению стрелки: Эта функция не работает в режимах DRY и FAN.
SLEEP - SLEEP ВЫКЛ – TURBO - TURBO ВЫКЛ
Кнопка SWING: Этой кнопкой включается поворот решетки. Повторное
нажатие выключает поворот.
Кнопка AIR DIRECTION: Эта кнопка изменяет угол наклона жалюзи.
С каждым нажатием кнопки угол наклона изменяется на 6º. Если
угол изменится настолько, что положение жалюзи будет уменьшать
охлаждающее или нагревающее действие кондиционера, то направление
движения жалюзи изменится. При нажатии этой кнопки на экране не
появляются символы.
Кнопка TIMER ON: Эта кнопка включает режим автоматического
включения по таймеру. С каждым нажатием кнопки настройка таймера
увеличивается на 30 минут. Когда настраиваемое время дойдет
до 10 часов, с каждым нажатием кнопки настройка таймера будет
увеличиваться на 60 минут. Чтобы выключить таймер, нажимайте кнопку
до появления пустого экрана.
Кнопка TIMER OFF: Эта кнопка включает режим автоматического
выключения по таймеру. С каждым нажатием кнопки настройка таймера
увеличивается на 30 минут. Когда настраиваемое время дойдет
до 10 часов, с каждым нажатием кнопки настройка таймера будет
увеличиваться на 60 минут. Чтобы выключить таймер, нажимайте кнопку
до появления пустого экрана.
4
3
Names and Functions of indicators on Remote Controller
TRANSMISSION Indicator:
This indicator lights when remote
controller transmits signals to indoor unit.
MODE indicator:
Displays the current operation modes.
Including AUTO( ), COOL( ), DRY( ) ,
HEAT( ) or FAN( ).
HEAT only available for heat pump model.
TEMPERATURE indicator:
SWING indicator:
This indicator lights up when the SWING
button is pressed.
FAN SPEED indicator:
Displays the selected fan speed, AUTO( ) and
three fan speed levels LOW( ), MED( ),
HIGH( ). Displays when the
operating mode is either AUTO or DRY.
(flashing)
TIMER indicator:
The time set for timer operation is indicated.
(0.5 ~ 24 hours)
NOTE: All items are shown in the Fig.2 for the purpose of clear
presentation But during the actual operation only the
relative functional items are shown on the display panel.
Display Panel
Fig. 2
1
2
3
4
5
7
Operating the Remote Controller
When the Air Conditioner is ready for use, switch on the power
and the OPERATION indicator lamp on the display panel of the
indoor unit starts flashing.
1. Use the select button to select AUTO.
2. Push the or button to set the desired room temperature.
The most comfortable temperature settings are between 21 C
to 28 C.
3. Push the button to start the air conditioner. The OPE-
RATION lamp on the display panel of the indoor unit lights. The
operating mode is AUTO. The FAN SPEED is automatically
controlled.
4. Push the button again to stop the unit operation.
Mode
On/off
On/off
1. When replacing batteries, do not use old batteries or a different
type battery. This may cause the remote controller to
malfunction.
2. If you do not use the remote controller for several weeks
remove the batteries. Otherwise battery leakage may damage
the remote controller.
3. The average battery life under normal use is about 6 months.
4. Replace the batteries when there is no answering beep from the
indoor unit or if the Transmission Indicator light fails to appear.
1. In the AUTO mode, the air conditioner can logically choose
the mode of COOL, FAN, HEAT and DRY by sensing the dif-
ference between the actual ambient room temperature and
the set temperature on the remote controller.
2. If the AUTO mode is not comfortable for you , the desired mode
can be selected manually.
Install / Replace Batteries
AUTOMATIC OPERATION
NOTE
NOTE
Hr.
ON TIMER
Hr.
Off TIMER
SET TEMP
Au to
2
6
7
5
4
3
Displays the temperature settings(17 to 30 ).
SLEEP/TURBO indicator:
Each time the Sleep/Turbo button is pushed, the
signal displays in the following sequence:
6
Au to
Use two alkaline dry batteries (R03/LR03X2).
Do not use rechargeable batteries.
(1) Remove the battery cover by pulling it according to the
arrow direction.
(2) Insert new batteries making sure that the
(+) and (-) of battery are installed correctly.
(3) Reattach the cover by sliding it back into position.
Tur bo
Turbo
Nothing
Nothing
Nothing appears when the operating mode is either
DRY or FAN only
4
3
Names and Functions of indicators on Remote Controller
TRANSMISSION Indicator:
This indicator lights when remote
controller transmits signals to indoor unit.
MODE indicator:
Displays the current operation modes.
Including AUTO( ), COOL( ), DRY( ) ,
HEAT( ) or FAN( ).
HEAT only available for heat pump model.
TEMPERATURE indicator:
SWING indicator:
This indicator lights up when the SWING
button is pressed.
FAN SPEED indicator:
Displays the selected fan speed, AUTO( ) and
three fan speed levels LOW( ), MED( ),
HIGH( ). Displays when the
operating mode is either AUTO or DRY.
(flashing)
TIMER indicator:
The time set for timer operation is indicated.
(0.5 ~ 24 hours)
NOTE: All items are shown in the Fig.2 for the purpose of clear
presentation But during the actual operation only the
relative functional items are shown on the display panel.
Display Panel
Fig. 2
1
2
3
4
5
7
Operating the Remote Controller
When the Air Conditioner is ready for use, switch on the power
and the OPERATION indicator lamp on the display panel of the
indoor unit starts flashing.
1. Use the select button to select AUTO.
2. Push the or button to set the desired room temperature.
The most comfortable temperature settings are between 21 C
to 28 C.
3. Push the button to start the air conditioner. The OPE-
RATION lamp on the display panel of the indoor unit lights. The
operating mode is AUTO. The FAN SPEED is automatically
controlled.
4. Push the button again to stop the unit operation.
Mode
On/off
On/off
1. When replacing batteries, do not use old batteries or a different
type battery. This may cause the remote controller to
malfunction.
2. If you do not use the remote controller for several weeks
remove the batteries. Otherwise battery leakage may damage
the remote controller.
3. The average battery life under normal use is about 6 months.
4. Replace the batteries when there is no answering beep from the
indoor unit or if the Transmission Indicator light fails to appear.
1. In the AUTO mode, the air conditioner can logically choose
the mode of COOL, FAN, HEAT and DRY by sensing the dif-
ference between the actual ambient room temperature and
the set temperature on the remote controller.
2. If the AUTO mode is not comfortable for you , the desired mode
can be selected manually.
Install / Replace Batteries
AUTOMATIC OPERATION
NOTE
NOTE
Hr.
ON T IM ER
Hr.
Off TI ME R
SET TEMP
Au to
2
6
7
5
4
3
Displays the temperature settings(17 to 30 ).
SLEEP/TURBO indicator:
Each time the Sleep/Turbo button is pushed, the
signal displays in the following sequence:
6
Au to
Use two alkaline dry batteries (R03/LR03X2).
Do not use rechargeable batteries.
(1) Remove the battery cover by pulling it according to the
arrow direction.
(2) Insert new batteries making sure that the
(+) and (-) of battery are installed correctly.
(3) Reattach the cover by sliding it back into position.
Tur bo
Turbo
Nothing
Nothing
Nothing appears when the operating mode is either
DRY or FAN only
Режимы COOL, HEAT и FAN ONLY
1. Если вам некомфортно при режиме AUTO, можно вручную отменить
заданные настройки, включив режим COOL, DRY, HEAT (только у
тепловых насосов) или FAN.
2. Кнопками и установить нужную температуру в помещении. В
режиме охлаждения (COOLING) наиболее комфортная температура
21 ºС и выше. В режиме отопления (HEATING) наиболее комфортная
температура 28 ºС и ниже.
3. Кнопкой FAN выбрать режим работы вентилятора AUTO, HIGH, MED или
LOW.
4. Нажать кнопку On/Off. Загорится световой сигнал «Включено» и
кондиционер начнет работать в заданном режиме. Выключить
кондиционер кнопкой ON/OFF.
ПРИМЕЧАНИЕ
В режиме FAN ONLY нельзя регулировать температуру. В этом режиме
можно выполнять только шаги 1, 3 и 4.
РЕЖИМ ОСУШЕНИЯ
1. Выбрать режим DRY кнопкой MODE.
2. Кнопкой или установить нужную температуру в помещении – от 21
ºC до 28 ºС.
3. Нажать кнопку On/Off. Загорится световой сигнал «Включено», и
кондиционер начнет работать в режиме осушения DRY. Выключить
кондиционер кнопкой ON/OFF.
ПРИМЕЧАНИЕ
Из-за разницы между заданной температурой и фактической
температурой в помещении кондиционер в режиме DRY часто работает, не
переключаясь в режимы COOL и FAN.
РАБОТА С ТАЙМЕРОМ
Нажать кнопку Timer ON или Timer OFF, чтобы настроить время включения
или выключения кондиционера по таймеру. С помощью пульта ДУ можно
настроить таймер на период от 0,5 до 24 часов.
1. Настройка времени включения.
1.1 Нажать кнопку TIMER ON. На экране появится надпись TIMER ON,
последнее установленное время включения, и символ Hr. Теперь
можно установить время включения.
1.2 Нажать кнопку TIMER ON еще раз и установить время включения.
1.3 После настройки времени включения таймера наступит пауза 0,5
секунды, а затем пульт ДУ передаст сигнал на кондиционер.
TEMP Button : Push this button to decrease the indoor
temperature setting.
RESET Button: When you press the recessed RESET button,
all current settings are cancelled and the control will return to
the initial settings.
SLEEP Button: Press this button to go into the Energy-Saving
operation mode. Press it again to cancel. This function is only
can be used on COOL, HEAT and AUTO mode and maintain the
most comfortable temperature for you.
2
NOTE: COOL only model has no HEAT feature.
!
1
6
ON/OFF Button: Push this button to start operation, push the
button again to stop operation.
9
TEMP Button : Push this button to increase the indoor
temperature setting .
2
AIR DIRECTION Button: Press this button to change the swing
angle of the louver. The swing angle of the louver is 6 for
each press. When the louver swing at a certain angle which
would affect the cooling and heating effect of the air conditioner,
it would automatically change the swing direction . No symbol
will appear in the display area when press this button. (Not
applicable to units without this function).
o
MODE Selection Button: Each time the button is pressed, the
operation mode is shifted in the direction of the arrow:
AUTO
COOL
DRY
HEAT
FAN
3
FAN SPEED Button: Used to select the Fan Speed in four steps-
AUTO LOW MED or HIGH. Each time the button is pressed,
the fan speed mode is shifted.
8
TIMER ON Button: Press this button to initiate the auto-on time
sequence. Each press will increase the auto-timed setting in 30
minutes increments. When the setting time displays 10:00, each
press will increase the auto-timed setting 60 minutes increments.
To cancel the auto-timed program, simply adjust the auto-on time
to 0:00.
10
11
4
5
NOTE: While the unit is running under SLEEP operation
mode, it would be canceled if you press the other button.
!
1
Model
Transmission Distance
Lowest Voltage of CPU
Emitting Signal
Rated Voltage
R51M/(C)E, R51M/BG(C)E, RG51M2/(C)E,
RG51A/(C)E, RG51M3/(C)E.
-5 C 60 C
8m (when using 3.0 voltage,
it Gets 11m)
3.0V(Alkaline dry batteries LR03 2)
2.0V
~
Remote Controller Specification
Performance Features
Features of the Remote controller buttons
1. Operating Mode: AUTO COOL DRY
HEAT(Cooling only model without) and FAN .
2. Timer Setting Function in 24 hours.
3. Indoor Setting Temperature Range : 17 C~30 C.
4. Full function of LCD (Liquid Crystal Display)
5. Back light emitting(only available for R51M/BG(C)E models)
Fig. 1
( C)
TEMP
AUTO
COOL
DRY
HEAT
FAN
HIGH
MED
LOW
MODE
FAN SPEED
TIMER ON
SLEEP
ON/OFF
TIMER OFF
AIR
DIRECTION
RESET LOCK
1
2
4
5
6
7
3
8
9
10
11
12
13
14
Environment
SET TEMPERATURE
SWING
LED
DISPLAY
TURBO
SWING Button: Push this switch button to activate auto
swing feature of the horizontal louver. Push it again to stop.
LED DISPLAY Button: Press this button to clear the digit
display in the air conditioner, press it again to activate it (Not
available for the units without LED display window).
7
*
*
*
*
*
*
*
*
NOTE:
: Indicates optional
button.
M odels RG51M2/(C)E:
without 14 and 15
buttons.
Models RG51M3/(C)E:
without 7 , 14 and
15 buttons.
Models R51M/(C)E
and R51M/BG(C)E:
without 15 button.
CLEAN
AIR
15
*
*
TEMP Button : Push this button to decrease the indoor
temperature setting.
RESET Button: When you press the recessed RESET button,
all current settings are cancelled and the control will return to
the initial settings.
SLEEP Button: Press this button to go into the Energy-Saving
operation mode. Press it again to cancel. This function is only
can be used on COOL, HEAT and AUTO mode and maintain the
most comfortable temperature for you.
2
NOTE: COOL only model has no HEAT feature.
!
1
6
ON/OFF Button: Push this button to start operation, push the
button again to stop operation.
9
TEMP Button : Push this button to increase the indoor
temperature setting .
2
AIR DIRECTION Button: Press this button to change the swing
angle of the louver. The swing angle of the louver is 6 for
each press. When the louver swing at a certain angle which
would affect the cooling and heating effect of the air conditioner,
it would automatically change the swing direction . No symbol
will appear in the display area when press this button. (Not
applicable to units without this function).
o
MODE Selection Button: Each time the button is pressed, the
operation mode is shifted in the direction of the arrow:
AUTO
COOL
DRY
HEAT
FAN
3
FAN SPEED Button: Used to select the Fan Speed in four steps-
AUTO LOW MED or HIGH. Each time the button is pressed,
the fan speed mode is shifted.
8
TIMER ON Button: Press this button to initiate the auto-on time
sequence. Each press will increase the auto-timed setting in 30
minutes increments. When the setting time displays 10:00, each
press will increase the auto-timed setting 60 minutes increments.
To cancel the auto-timed program, simply adjust the auto-on time
to 0:00.
10
11
4
5
NOTE: While the unit is running under SLEEP operation
mode, it would be canceled if you press the other button.
!
1
Model
Transmission Distance
Lowest Voltage of CPU
Emitting Signal
Rated Voltage
R51M/(C)E, R51M/BG(C)E, RG51M2/(C)E,
RG51A/(C)E, RG51M3/(C)E.
-5 C 60 C
8m (when using 3.0 voltage,
it Gets 11m)
3.0V(Alkaline dry batteries LR03 2)
2.0V
~
Remote Controller Specification
Performance Features
Features of the Remote controller buttons
1. Operating Mode: AUTO COOL DRY
HEAT(Cooling only model without) and FAN .
2. Timer Setting Function in 24 hours.
3. Indoor Setting Temperature Range : 17 C~30 C.
4. Full function of LCD (Liquid Crystal Display)
5. Back light emitting(only available for R51M/BG(C)E models)
Fig. 1
( C)
TEMP
AUTO
COOL
DRY
HEAT
FAN
HIGH
MED
LOW
MODE
FAN SPEED
TIMER ON
SLEEP
ON/OFF
TIMER OFF
AIR
DIRECTION
RESET LOCK
1
2
4
5
6
7
3
8
9
10
11
12
13
14
Environment
SET TEMPERATURE
SWING
LED
DISPLAY
TURBO
SWING Button: Push this switch button to activate auto
swing feature of the horizontal louver. Push it again to stop.
LED DISPLAY Button: Press this button to clear the digit
display in the air conditioner, press it again to activate it (Not
available for the units without LED display window).
7
*
*
*
*
*
*
*
*
NOTE:
: Indicates optional
button.
M odels RG51M2/(C)E:
without 14 and 15
buttons.
Models RG51M3/(C)E:
without 7 , 14 and
15 buttons.
Models R51M/(C)E
and R51M/BG(C)E:
without 15 button.
CLEAN
AIR
15
*
*
TEMP Button : Push this button to decrease the indoor
temperature setting.
RESET Button: When you press the recessed RESET button,
all current settings are cancelled and the control will return to
the initial settings.
SLEEP Button: Press this button to go into the Energy-Saving
operation mode. Press it again to cancel. This function is only
can be used on COOL, HEAT and AUTO mode and maintain the
most comfortable temperature for you.
2
NOTE: COOL only model has no HEAT feature.
!
1
6
ON/OFF Button: Push this button to start operation, push the
button again to stop operation.
9
TEMP Button : Push this button to increase the indoor
temperature setting .
2
AIR DIRECTION Button: Press this button to change the swing
angle of the louver. The swing angle of the louver is 6 for
each press. When the louver swing at a certain angle which
would affect the cooling and heating effect of the air conditioner,
it would automatically change the swing direction . No symbol
will appear in the display area when press this button. (Not
applicable to units without this function).
o
MODE Selection Button: Each time the button is pressed, the
operation mode is shifted in the direction of the arrow:
AUTO
COOL
DRY
HEAT
FAN
3
FAN SPEED Button: Used to select the Fan Speed in four steps-
AUTO LOW MED or HIGH. Each time the button is pressed,
the fan speed mode is shifted.
8
TIMER ON Button: Press this button to initiate the auto-on time
sequence. Each press will increase the auto-timed setting in 30
minutes increments. When the setting time displays 10:00, each
press will increase the auto-timed setting 60 minutes increments.
To cancel the auto-timed program, simply adjust the auto-on time
to 0:00.
10
11
4
5
NOTE: While the unit is running under SLEEP operation
mode, it would be canceled if you press the other button.
!
1
Model
Transmission Distance
Lowest Voltage of CPU
Emitting Signal
Rated Voltage
R51M/(C)E, R51M/BG(C)E, RG51M2/(C)E,
RG51A/(C)E, RG51M3/(C)E.
-5 C 60 C
8m (when using 3.0 voltage,
it Gets 11m)
3.0V(Alkaline dry batteries LR03 2)
2.0V
~
Remote Controller Specification
Performance Features
Features of the Remote controller buttons
1. Operating Mode: AUTO COOL DRY
HEAT(Cooling only model without) and FAN .
2. Timer Setting Function in 24 hours.
3. Indoor Setting Temperature Range : 17 C~30 C.
4. Full function of LCD (Liquid Crystal Display)
5. Back light emitting(only available for R51M/BG(C)E models)
Fig. 1
( C)
TEMP
AUTO
COOL
DRY
HEAT
FAN
HIGH
MED
LOW
MODE
FAN SPEED
TIMER ON
SLEEP
ON/OFF
TIMER OFF
AIR
DIRECTION
RESET LOCK
1
2
4
5
6
7
3
8
9
10
11
12
13
14
Environment
SET TEMPERATURE
SWING
LED
DISPLAY
TURBO
SWING Button: Push this switch button to activate auto
swing feature of the horizontal louver. Push it again to stop.
LED DISPLAY Button: Press this button to clear the digit
display in the air conditioner, press it again to activate it (Not
available for the units without LED display window).
7
*
*
*
*
*
*
*
*
NOTE:
: Indicates optional
button.
M odels RG51M2/(C)E:
without 14 and 15
buttons.
Models RG51M3/(C)E:
without 7 , 14 and
15 buttons.
Models R51M/(C)E
and R51M/BG(C)E:
without 15 button.
CLEAN
AIR
15
*
*
TEMP Button : Push this button to decrease the indoor
temperature setting.
RESET Button: When you press the recessed RESET button,
all current settings are cancelled and the control will return to
the initial settings.
SLEEP Button: Press this button to go into the Energy-Saving
operation mode. Press it again to cancel. This function is only
can be used on COOL, HEAT and AUTO mode and maintain the
most comfortable temperature for you.
2
NOTE: COOL only model has no HEAT feature.
!
1
6
ON/OFF Button: Push this button to start operation, push the
button again to stop operation.
9
TEMP Button : Push this button to increase the indoor
temperature setting .
2
AIR DIRECTION Button: Press this button to change the swing
angle of the louver. The swing angle of the louver is 6 for
each press. When the louver swing at a certain angle which
would affect the cooling and heating effect of the air conditioner,
it would automatically change the swing direction . No symbol
will appear in the display area when press this button. (Not
applicable to units without this function).
o
MODE Selection Button: Each time the button is pressed, the
operation mode is shifted in the direction of the arrow:
AUTO
COOL
DRY
HEAT
FAN
3
FAN SPEED Button: Used to select the Fan Speed in four steps-
AUTO LOW MED or HIGH. Each time the button is pressed,
the fan speed mode is shifted.
8
TIMER ON Button: Press this button to initiate the auto-on time
sequence. Each press will increase the auto-timed setting in 30
minutes increments. When the setting time displays 10:00, each
press will increase the auto-timed setting 60 minutes increments.
To cancel the auto-timed program, simply adjust the auto-on time
to 0:00.
10
11
4
5
NOTE: While the unit is running under SLEEP operation
mode, it would be canceled if you press the other button.
!
1
Model
Transmission Distance
Lowest Voltage of CPU
Emitting Signal
Rated Voltage
R51M/(C)E, R51M/BG(C)E, RG51M2/(C)E,
RG51A/(C)E, RG51M3/(C)E.
-5 C 60 C
8m (when using 3.0 voltage,
it Gets 11m)
3.0V(Alkaline dry batteries LR03 2)
2.0V
~
Remote Controller Specification
Performance Features
Features of the Remote controller buttons
1. Operating Mode: AUTO COOL DRY
HEAT(Cooling only model without) and FAN .
2. Timer Setting Function in 24 hours.
3. Indoor Setting Temperature Range : 17 C~30 C.
4. Full function of LCD (Liquid Crystal Display)
5. Back light emitting(only available for R51M/BG(C)E models)
Fig. 1
( C)
TEMP
AUTO
COOL
DRY
HEAT
FAN
HIGH
MED
LOW
MODE
FAN SPEED
TIMER ON
SLEEP
ON/OFF
TIMER OFF
AIR
DIRECTION
RESET LOCK
1
2
4
5
6
7
3
8
9
10
11
12
13
14
Environment
SET TEMPERATURE
SWING
LED
DISPLAY
TURBO
SWING Button: Push this switch button to activate auto
swing feature of the horizontal louver. Push it again to stop.
LED DISPLAY Button: Press this button to clear the digit
display in the air conditioner, press it again to activate it (Not
available for the units without LED display window).
7
*
*
*
*
*
*
*
*
NOTE:
: Indicates optional
button.
M odels RG51M2/(C)E:
without 14 and 15
buttons.
Models RG51M3/(C)E:
without 7 , 14 and
15 buttons.
Models R51M/(C)E
and R51M/BG(C)E:
without 15 button.
CLEAN
AIR
15
*
*

Содержание

Похожие устройства

Скачать