Ebara BHS 511-26 [5/59] Introduction

Ebara BHS 516-34 [5/59] Introduction
5
OPERATING AND MAINTENANCE MANUAL PART 2
THE USER SHOULD KEEP THIS DOCUMENT
1. INTRODUCTION
This instruction manual is split into two booklets: PART 1, contain-
ing general information regarding our whole product range; and
PART 2, containing information speci c to the motor-driven pump
you have purchased. The two publications are complementary to
each other, so make sure you have both.
Comply with the instructions contained in them to get the most out
of your motor-driven pump and assure its proper operation. If you
need further information, get in touch with your nearest author-
ized dealer.
If information in the two parts contradict each other, take PART 2
containing the product’s speci c information as valid.
NO PART OF THESE ILLUSTRATIONS AND/OR TEXT MAY BE
REPRODUCED FOR ANY REASON.
The following symbols have been used in the compilation of this
instruction booklet.
WARNING
Risk of damaging the pump or system
Risk of causing injury or damaging property
Electrical hazard
2. CONTENTS
1. INTRODUCTION page 5
2. CONTENTS page 5
3. DESCRIPTION AND USE OF MOTOR-DRIVEN PUMP page 5
4. SPECIFICATIONS page 5
5. PREPARING FOR USE page 6
6. TECHNICAL LITERATURE page 52
3. DESCRIPTION AND USE OF MOTOR-DRIVEN PUMP
3.1. DESCRIPTION
Description:
SUBMERSIBLE CENTRIFUGAL
MOTORDRIVEN PUMPS
Model: WINNER
BHS
IDROGO
3.2. USE FOR WHICH PUMPS ARE DESIGNED
The pumps can be used for lifting and distributing clean water
or water with a sand content not exceeding the limit given in
chap. 4.
The submersible motor-driven pumps are used:
for domestic and industrial water supply systems;
Pressure boosting systems;
Medium-capacity sprinkler systems for re ghting (WINNER-
BHS);
– fountains;
small and medium-sized jet or ood irrigation systems;
for any applications involving drawing water from a well.
Use the motor-driven pumps based on their technical speci ca-
tions.
3.3. USE FOR WHICH PUMPS ARE NOT DESIGNED
The submersible motor-driven pumps must not be made to
work without water. If there is any chance of the waterbed low-
ering to a point where the pump will be exposed, you will need
to install a minimum-level sensor as a safety measure.
4. SPECIFICATIONS
BHS and WINNER series pumps come in versions with a water-bath
motor (WY) or Marcol 82 oil-bath motor (OY) and the nonreturn
valve is built into the pump;
4.1. PUMP SPECIFICATIONS
U.M. BHS WINNER IDROGO
Max. temperature
of liquid pumped
°C 60 40
Max. amount
of sand in
suspension
g/m
3
50
Max. size
of solids
mm 2,5
Type of liquid
pumped
Clean water
4.2. WATER-BATH MOTOR SPECIFICATIONS: WY
Pump 4BHS 6BHS
WINNER
IDROGO
Max. temperature
of liquid pumped
°C
35 Sumoto
30 Franklin
40
Insulation class
B Franklin
F Sumoto
F
B Franklin
F Sumoto
F
IP rating
IP
58 Sumoto
68 Franklin
68
Type of duty
Continuo S1
Maximum immersion
m
150 Sumoto
350 Franklin
20
Max. starts per hour
n.°
30 Sumoto
20 Franklin
20
4.3. OIL-BATH MOTOR SPECIFICATIONS: OY
Pump 4BHS 6BHS
WINNER
Max. temperature
of liquid pumped
°C 35
Insulation class
–F
IP rating
IP 58
Type of duty
Continuo S1
Maximum immersion
m150
Max. starts
per hour
n.°
30
4.4. RATING PLATES
The manufacturer reserves the right to make changes.
4.4.1. WINNER PUMP RATING PLATE
Below is the adhesive rating plate applied to WINNER-series pumps.
For descriptions of numerical values, see PART 1 chap. 12.
GB
libretto_EBARA_382_nuovo.indd 5libretto_EBARA_382_nuovo.indd 5 6-02-2009 9:39:006-02-2009 9:39:00

Содержание

Скачать