Scarlett SC-058 Инструкция по эксплуатации онлайн [3/4] 28872

Scarlett SC-058 Инструкция по эксплуатации онлайн [3/4] 28872
IM007
www.scarlett.ru SC-058
3
GB INSTRUCTION MANUAL
IMPORTANT SAFEGUARDS
Please read all the instruction manual before use and
save it for future references.
Before first switching on check that the voltage indicated
on the rating label corresponds with the mains voltage in
your home.
For home use only. Do not use for industrial purposes.
Use the appliance only for its intended use.
Do not use outdoors or in damp area.
Do not immerse the appliance and the cord in water or
other liquids.
Never pull the cord while disconnecting from the power
outlet; instead, grasp the plug only and pull to disconnect.
Do not allow the cord to touch sharp edges and hot
surfaces.
Always unplug the appliance from the power supply when
not in use.
Do not operate the appliance with damaged cord or plug,
or after the appliance malfunctions, or has been dropped
or damaged in any manner. To avoid the risk of electric
shock, do not disassemble the appliance; take it to a
service center for examination, repair or mechanical
adjustment.
This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliances by a person responsible
for their safety.
Children should be supervised to ensure that they do not
play with the appliance.
Do not leave appliance unattended while operating.
The appliance must be used only in the upright position.
Unit surface temperature of the appliance is high, thus do
not touch it, except the handle.
Operating unit should be far away from the flammable or
easy bulging under high temperature objects.
CAUTION:
To avoid a circuit overload, do not operate another high
wattage appliance on the same circuit.
Do not cover the appliance when in use.
The heater is filled with a certain quantity of special oil.
Any maintenance that requires opening of the oil tank
may be performed only by the manufacturer or its
authorized service center that should repair the appliance
in case of oil leakage.
It is necessary to follow the instructions concerning used
oil utilization.
ASSEMBLING
First turn the unit upside-down.
Install multidirectional rolling wheels to each end between
the first and the second groups of the heating flanges.
Let the “U” shape screw surround the dome of the heating
flanges. Then insert it into two holes of the supporting
plate.
Use butterfly nuts to screw them tightly counterclockwise.
Place heater normally and make sure that it is
inconvertible.
USING THE APPLIANCE
Set thermostat to minimal position and power switch to
“Off” position, plug in the appliance.
POWER SELECTOR
You can adjust oil heater current power using power
regulator:
“0” Off;
“I“ Minimum power;
“II” Medium power;
“III” Maximum power.
THERMOSTAT
Set thermostat to maximum position.
When the temperature rises to satisfying level, slowly turn
the thermostat counterclockwise until the indicator lights
is out, and the room temperature thus can keep constant.
If you want to change the room temperature, you can
make another regulation: turn the thermostat clockwise to
arise the temperature and counterclockwise to lower it.
When the temperature is below than thermostat set value,
heating element will switch on and corresponding
indicator will light (or both indicators if maximum power
was set).
TIMER OPERATION
Timer allows to set operation time and duration (up to 24
hours).
Slide switch ”A” to position.
Turn timer knob in direction shown by round arrows and
set current time opposite mark “”.
Using microswitches ”B” around the timer, set the
operation duration.
To do it, put the switch “B” to outer position in periods of
time when you want the heater operating.
One white mini switch means 15 minutes of operation.
Set switch “A” to “I” position for continuous operating.
NOTES:
The room must be properly sealed, if not, using of oil
heater will not make good result because of heat
leakage.
After use, turn the power selector to the “0” position, then
turn the thermostat to the “MIN” position and unplug from
power supply.
CLEAN AND CARE
The oil heater should be cleaned regularly to wipe out the
dust on the surface of fins. As this may result the radiating
efficient.
Unplug from the power supply and allow the appliance to
cool down.
Wipe out with a soft damp cloth. Do not use detergent or
abrasives.
Do not scrap the surfaces of fins with sharp hard tools, to
avoid surfaces getting rusty, because of damage of the
paint coat.
STORAGE
Switch off and unplug the appliance. Ensure the oil heater
is completely cool.
Complete all requirements of chapter CLEAN AND
CARE.
Reel on the power cord.
Keep the appliance in a dry cool place.
RUS РУКОВОДСТВО ПО ЭКСПЛУАТАЦИИ
МЕРЫ БЕЗОПАСНОСТИ
Внимательно прочитайте данную инструкцию перед
эксплуатацией прибора во избежание поломок при
использовании. Неправильное обращение может
привести к поломке изделия, нанести материальный
ущерб или причинить вред здоровью пользователя.
Перед первоначальным включением проверьте,
соответствуют ли технические характеристики
изделия, указанные на наклейке, параметрам
электросети.
Использовать только в бытовых целях. Прибор не
предназначен для промышленного применения.
Не использовать вне помещений или в условиях
повышенной влажности.
Не погружайте прибор или шнур питания в воду или
другие жидкости.
При отключении прибора от сети питания держитесь
рукой за вилку, не тяните за шнур питания.
Следите за тем, чтобы шнур питания не касался
острых кромок и горячих поверхностей.
Всегда отключайте прибор от электросети, если он не
используется.
Скачать
Случайные обсуждения