![Invertek Drives ODE-2-14075-3KA1 [2/24] Company information](/img/pdf.png)
Invertek Drives ODE-2-14075-3KA1 [2/24] Company information
![Invertek Drives ODE-2-12150-1K01 [2/24] Company information](/views2/1583971/page2/bg2.png)
2 Optidrive E2 IP66 / NEMA 4X User Guide
www.invertek.co.uk
Declaration of Conformity:
Invertek Drives Ltd hereby states that the Optidrive E2 product range conforms to the relevant safety provisions of the Low Voltage
Directive 2006/95/EC and the EMC Directive 2004/108/EC and has been designed and manufactured in accordance with the following
harmonised European standards:
EN 61800-5-1: 2003
Adjustable speed electrical power drive systems. Safety requirements. Electrical, thermal and
energy.
EN 61800-3 2
nd
Ed: 2004
Adjustable speed electrical power drive systems. EMC requirements and specific test methods
EN 55011: 2007
Limits and Methods of measurement of radio disturbance characteristics of industrial, scientific and
medical (ISM) radio-frequency equipment (EMC)
EN60529 : 1992
Specifications for degrees of protection provided by enclosures
Electromagnetic Compatibility
All Optidrives are designed with high standards of EMC compliance in mind. All versions suitable for operation on Single Phase 230
volt and Three Phase 400 volt supplies and intended for use within the European Union can be fitted with an internal EMC filter. This
EMC filter is designed to reduce the conducted emissions back into the supply via the power cables for compliance with harmonised
European standards.
It is the responsibility of the installer to ensure that the equipment or system into which the product is incorporated complies with the
EMC legislation of the country of use. Within the European Union, equipment into which this product is incorporated must comply with
the EMC Directive 2004/108/EC. When using an Optidrive with an internal or optional external filter, compliance with the following EMC
Categories, as defined by EN61800-3:2004 can be achieved:
Drive Type / Rating
EMC Category
Cat C1
Cat C2
Cat C3
1 Phase, 230 Volt Input
ODE-2-x2xxx-xxBxx
No additional filtering required
Use shielded motor cable
3 Phase, 400 Volt Input
ODE-2-x4xxx-xxAxx
Use External Filter OD-Fx34x
No additional filtering required
Use screened motor cable
Note
For motor cable lengths greater than drive rated cable length, an output dv / dt filter must be used (part number OD-OUTFx,
please refer to the Invertek Stock Drives Catalogue for further details)
Company Information
Address:
Invertek Drives Ltd.
Offa's Dyke Business Park
Welshpool
Powys
SY21 8JF
United Kingdom
Email:
sales@invertek.co.uk
Website:
www.invertek.co.uk
All rights reserved. No part of this User Guide may be reproduced or transmitted in any form or by any means, electrical or mechanical
including photocopying, recording or by any information storage or retrieval system without permission in writing from the publisher.
Copyright Invertek Drives Ltd ©2009
The manufacturer accepts no liability for any consequences resulting from inappropriate, negligent or incorrect installation, or
adjustment of the optional operating parameters of the drive or from mismatching of the drive to the motor.
The contents of this User Guide are believed to be correct at the time of printing. In the interest of a commitment to a policy of
continuous improvement, the manufacturer reserves the right to change the specification of the product or its performance or the
contents of the User Guide without notice.
All Invertek drives products carry a 2-year warranty, valid from the date of manufacture. This date is clearly visible on the product rating
label.
This User Guide is for use with V1.02 Software.
User Guide Issue 1.00
Содержание
- Company information 2
- Declaration of conformity 2
- Electromagnetic compatibility 2
- Analog and digital input configurations 19 3
- Control wiring 12 3
- General information and ratings 5 3
- Introduction 4 3
- Mechanical installation 6 3
- Operation 12 3
- Parameters 15 3
- Power wiring 8 3
- Technical data 22 3
- Troubleshooting 22 3
- Important safety information 4
- Introduction 4
- 115v 10 1 phase input 3 phase 230v output voltage doubler 5
- 240v 10 1 phase input 5
- 240v 10 3 phase input 5
- 480v 10 3 phase input 5
- Drive model numbers 5
- Each drive can be identified by its model number as shown in figure 1 drive model number format the model number is on the shipping label and the drive nameplate the model number includes the drive and any options drive model numbers for the optidrive e2 drives are provided in 10 rating tables 5
- Figure 1 drive model number format 5
- For ip66 nema 4x with switches switched change the for a y at the end of the product code for ip66 nema 4x without switches non switched change the for a x at the end of the product code 5
- General information and ratings 5
- Identifying the drive by model number 5
- Optidrive e2 ip66 nema 4x user guide 5
- This chapter contains information about the optidrive e2 including how to identify the drive 5
- Www invertek co uk 5
- A b d e f g h i j 6
- Avoid condensation built up in the drive the washdown process of the drive may create a temperature and humidity change avoid condensation built up in the drive the washdown process of the drive may create a temperature and humidity change in and around the drive if the unit is mounted in a cool environment and washed down with higher temperature water as the drive cools to room temperature condensation can form inside the drive especially around the display to prevent this from happening avoid using sealed connectors around rubber coated cables to seal the drive these do not allow any air transfer and hence create a level of condensation and humidity that exceeds the drive s rating 6
- Control terminal torque settings of 0 nm 4 lb in power terminal torque settings of 1 nm 9 lb in 6
- Drive size 6
- Ensure that all terminals are tightened to the appropriate torque setting ensure that all terminals are tightened to the appropriate torque setting 6
- General 6
- Install the optidrive on a flat vertical flame resistant vibration free mounting if higher ip nema ratings are required mount install the optidrive on a flat vertical flame resistant vibration free mounting if higher ip nema ratings are required mount within a suitable enclosure according to en60529 6
- Mechanical dimensions and mounting 6
- Mechanical installation 6
- Mm in mm in mm in mm in mm in mm in mm in mm in mm in 6
- Mount the drive vertically and do not restrict the air flow to the heat sink fins the drive generates heat allow sufficient space mount the drive vertically and do not restrict the air flow to the heat sink fins the drive generates heat allow sufficient space around the unit for heat dissipation do not mount the drive near heat radiating elements or in direct sunlight 6
- Optidrive e2 ip66 nema 4x user guide 6
- Store the optidrive in its box until required storage should be clean and dry and within the temperature range 40 c to 60 c 6
- The ip66 nema 4x drive is intended for indoor use only the ip66 nema 4x drive is intended for indoor use only 6
- The ip66 nema 4x optidrives can be installed side by side the ip66 nema 4x optidrives can be installed side by side with their heatsink flanges touching this gives adequate ventilation space between drives if the optidrive is to be installed above another drive or any other heat producing device the minimum vertical spacing is 150mm 5 inches above and below mount the drive vertically and do not restrict the air flow to the heat sink fins 6
- The optidrive must be installed in a pollution degree 1 or 2 environment the optidrive must be installed in a pollution degree 1 or 2 environment 6
- Www invertek co uk 6
- Gland sizes lock off 7
- Removing the terminal cover 7
- Grounding guidelines 8
- Grounding the drive 8
- Power wiring 8
- Wiring precautions 8
- Connection diagrams 9
- Ip66 nema 4x switched 9
- Ip66 nema 4x non switched 10
- Drive and motor connections 11
- Motor terminal box connections 11
- Control terminal connections 12
- Control wiring 12
- Managing the keypad 12
- Operation 12
- Rj45 data connection 12
- Changing parameters 13
- Keypad control 13
- Reset factory default settings 13
- Terminal control 13
- P 12 p 15 14
- Parameters to 14
- Set notes 14
- Switch position 14
- Using the rev 0 fwd selector switch switched version only 14
- Parameters 15
- Standard parameters 15
- Extended parameters 16
- P 00 read only drive status parameters 18
- Parameter group zero access and navigation 18
- Analog and digital input configurations 19
- Analog speed input with 1 preset speed 19
- Analog speed input with 2 preset speeds 4 preset speeds and max speed select 19
- And fwd rev switch 19
- Optidrive e2 ip66 nema 4x user guide 19
- Switch effectively giving 5 preset speeds 19
- Terminal mode p 12 0 19
- Typical applications 19
- Www invertek co uk 19
- 2 analog inputs 20
- Analog speed input with 1 preset speed 20
- And motor thermistor trip 20
- Deceleration ramp 20
- Example wiring 20
- Fwd rev 20
- Keypad mode p 12 1 or 2 20
- Local or remote analog speeds 20
- Optidrive e2 ip66 nema 4x user guide 20
- Push button fwd rev stop with fast stop 20
- Remote push button speed control with 20
- Www invertek co uk 20
- Example wiring 21
- Further information on configuring the pi controller for typical feedback applications please refer to the application note an ode 02 21
- Further information the modbus rtu register map information and communication setup please refer to the application note an ode 01 21
- Modbus control mode p12 3 or 4 21
- Optidrive e2 ip66 nema 4x user guide 21
- Remote closed loop pi feedback control 21
- Thermistor trip 21
- User pi control mode p 12 5 or 6 21
- With local analog speed input 21
- With local preset speed 1 21
- With local preset speed 1 and motor 21
- Www invertek co uk 21
- Environmental 22
- Fault messages 22
- Operational ambient temperature range 10 40 c frost and condensation free storage ambient temperature range 40 60 c maximum altitude 2000m derate above 1000m 1 100m maximum humidity 95 non condensing 22
- Optidrive e2 ip66 nema 4x user guide 22
- Technical data 22
- Troubleshooting 22
- Www invertek co uk 22
- 115v 10 1 phase input 3 phase 230v output voltage doubler 23
- 240v 10 1 phase input 3 phase output 23
- 240v 10 3 phase input 3 phase output 23
- 480v 10 3 phase input 3 phase output 23
- Maximum supply ratings for ul compliance 23
- Rating tables 23
Похожие устройства
- Invertek Drives ODE-2-14150-3KA1 Инструкция по эксплуатации
- Invertek Drives ODE-2-24150-3KA4 Инструкция по эксплуатации
- Invertek Drives ODE-2-24220-3KA4 Инструкция по эксплуатации
- Invertek Drives ODE-2-24400-3KA4 Инструкция по эксплуатации
- Invertek Drives ODE-2-34055-3KA4 Инструкция по эксплуатации
- Invertek Drives ODE-2-34075-3KA4 Инструкция по эксплуатации
- Invertek Drives ODE-2-14075-3K01 Инструкция по эксплуатации
- Invertek Drives ODE-2-14150-3K01 Инструкция по эксплуатации
- Invertek Drives ODE-2-24150-3K04 Инструкция по эксплуатации
- Invertek Drives ODE-2-24220-3K04 Инструкция по эксплуатации
- Invertek Drives ODE-2-24400-3K04 Инструкция по эксплуатации
- Invertek Drives ODE-2-34055-3K04 Инструкция по эксплуатации
- Invertek Drives ODE-2-34075-3K04 Инструкция по эксплуатации
- Invertek Drives ODP-2-22075-1KF42 Инструкция по эксплуатации
- Invertek Drives ODP-2-22150-1KF42 Инструкция по эксплуатации
- Invertek Drives ODP-2-22220-1KF42 Инструкция по эксплуатации
- Invertek Drives ODP-2-22075-3KF42 Инструкция по эксплуатации
- Invertek Drives ODP-2-22150-3KF42 Инструкция по эксплуатации
- Invertek Drives ODP-2-22220-3KF42 Инструкция по эксплуатации
- Invertek Drives ODP-2-32040-3KF42 Инструкция по эксплуатации