Qtech QSW-8200-28T-POEAC- DC [23/39] Chapter 2 ipv6 multicast protocol
![Qtech QSW-8200-28T-POEAC- DC [23/39] Chapter 2 ipv6 multicast protocol](/views2/1596644/page23/bg17.png)
User Manual
Chapter 2. IPv6 Multicast Protocol 23
www.qtech.ru
Chapter 2 IPV6 MULTICAST PROTOCOL
2.1 Commands for IPv6 DCSCM
2.1.1 ipv6 access-list(ipv6 multicast source control)
Command: ipv6 access-list <8000-8099> {deny|permit} {{<source/M> }|{host-source
<source-host-ip>}|any-source} {{<destination/M> }|{host-destination <destination-
host-ip>}|any-destination}
no ipv6 access-list <8000-8099> {deny|permit} {{<source/M>}|{host-
source <source-host-ip>}|any-source} {{<destination/M> }|{host-
destination <destination-host-ip>}|any-destination}
Function: Configure IPv6 source control multicast access list, the no operation of this
command is used to delete the access list.
Parameters: <8000-8099>: The source control access list number.
{deny|permit}: Deny or permit.
<source/M>: The multicast source address and the length of mask.
<source-host-ip>: The multicast host address.
<destination/M>: The multicast destination address and the length of
mask.
<destination-host-ip>: The multicast destination host addresses.
Default: None.
Command Mode: Global Configuration Mode.
Usage Guide: IPv6 multicast source control entries control the ACL it uses with ACL
number 8000-8099, this command is used to configure such ACL. IPv6 multicast source
control ACL only needs to configure the source IPv6 address and destination IPv6
address (that is the group IPv6 addresses)which are to be controlled, the configuration
adopts a method similar to other ACLs, which can either be an address range
configured by the length of mask, or a specified host address or all addresses. Pay
attention to that: for group IPv6 addresses, the “all addresses” mentioned here is ff:/8.
Example:
Switch(config)#ipv6 access-list 8000 permit fe80::203:228a/64 ff1e::1/64
2.1.2 ipv6 access-list(multicast destination control)
Command: ipv6 access-list <9000-10999> {deny|permit} {{<source/M> }|{host-source
<source-host-ip>}|any-source} {{<destination/M> }|{host-destination <destination-
host-ip>}|any-destination}
no ipv6 access-list <9000-10999> {deny|permit} {{<source/M>
}|{host-source <source-host-ip>}|any-source}
{{<destination/M> }|{host-destination <destination-host-
ip>}|any-destination}
Содержание
- Chapter 1 ipv4 multicast protocol 5 2
- Commands for dcscm 5 2
- Commands for igmp snooping 12 2
- Content 2
- Chapter 2 ipv6 multicast protocol 23 3
- Commands for ipv6 dcscm 23 3
- Commands for mld snooping configuration 29 3
- Chapter 1 ipv4 multicast protocol 5
- Commands for dcscm 5
- Clear ip igmp snooping vlan 12
- Command debug igmp snooping all packet event timer mfc no debug igmp snooping all packet event timer mfc function enable the igmp snooping switch of the switch the no debug igmp 12
- Command ip igmp snooping 12
- Command mode admin mode default igmp snooping debugging switch is disabled on the switch by default usage guide the command is used for enable the igmp snooping debugging switch of 12
- Commands for igmp snooping 12
- Debug igmp snooping all packet event timer mfc 12
- Ip igmp snooping 12
- Mrouter port 12
- Snooping all packet event timer mfc disables the debugging switch 12
- Switch clear ip igmp snooping vlan 1 mrouter port 12
- The switch switch igmp data packet message can be shown with packet parameter event message with event timer message with time downsending hardware entries message with mfc and all debugging messages with all 12
- Chapter 2 ipv6 multicast protocol 23
- Commands for ipv6 dcscm 23
- Commands for mld snooping configuration 29
- Chapter 3 commands for multicast vlan 38
- Multicast vlan 38
- Multicast vlan association 38
- Multicast vlan association interface 39
- Switchport association multicast vlan 39
Похожие устройства
- Qtech QSW-8200-28T-POEAC- DC Команды для функции безопасности
- Qtech QSW-8200-28T-POEAC- DC Команды интерфейса уровня 3
- Qtech QSW-8200-28T-POEAC- DC Команды надёжности
- Qtech QSW-8200-28T-POEAC- DC Команды настройки vlan
- Qtech QSW-8200-28T-POEAC- DC Команды отладки и диагностики
- Qtech QSW-8200-28T-POEAC- DC Команды управления сетевым временем
- Qtech QSW-8200-28T-POEAC- DC Руководство пользователя
- Qtech QSW-8200-28F-AC-DC Команды для dhcp-сервера
- Qtech QSW-8200-28F-AC-DC Команды для mstp
- Qtech QSW-8200-28F-AC-DC Команды для poe
- Qtech QSW-8200-28F-AC-DC Команды для qos
- Qtech QSW-8200-28F-AC-DC Команды для базовой конфигурации
- Qtech QSW-8200-28F-AC-DC Команды для настройки портов
- Qtech QSW-8200-28F-AC-DC Команды для потокового монитора
- Qtech QSW-8200-28F-AC-DC Команды для протокола маршрутизаций
- Qtech QSW-8200-28F-AC-DC Команды для протокола многоадресной рассылки
- Qtech QSW-8200-28F-AC-DC Команды для функции безопасности
- Qtech QSW-8200-28F-AC-DC Команды интерфейса уровня 3
- Qtech QSW-8200-28F-AC-DC Команды надёжности
- Qtech QSW-8200-28F-AC-DC Команды настройки vlan