Home
Главная
Bosch
Мойка Высокого Давления
AdvancedAquatak 140 (06008A7D00)
Инструкция по эксплуатации Страница: 17

Bosch AdvancedAquatak 140 (06008A7D00) [17/294] For your safety

English | 17

3 600 HA7 D00

– Vibration emission value a

m/s

0.5

– Uncertainty K m/s

= 0.5

Mounting and Operation

Action Figure Page

Delivery scope

A 280

Adjusting the Handle

B 280

Connecting high pressure gun

to lance

C 281

Connecting high pressure wa-

ter supply hose/nozzle

D 281

Attaching Nozzle

Adjusting water jet

E – F 282 - 283

Connect detergent bottle

G 284

Connecting to the water supply

H 285

Switching On and Off

I 285

Clean the water filter

J 286

Clean nozzle

K 286

Gun storage

L 287

Gun/lance/nozzle stored during

work breaks

M 287

Storage

M 287

Selecting Accessories

N 288

Switching on

For Your Safety

Warning: Switch off, remove plug from

mains before adjusting, cleaning or if cable

is cut, damaged or entangled.

The operating voltage is 230VAC, 50Hz (for non-EU coun-

tries 220V, 240V as applicable). Contact your Bosch Ser-

vice Centre for details. If in doubt contact a qualified electri-

cian or the nearest Bosch Service Centre.

If you want to use an extension cable when operating your

high pressure washer, only the following cable dimensions

should be used:

– 2.5mm

– max length 25m

Note: If an extension cable is used it must be earthed and

connected through the plug to the earth cable of your supply

network in accordance with prescribed safety regulations.

If in doubt contact a qualified electrician or the nearest

Bosch Service Centre.

WARNING! Inadequate extension cables can

be dangerous. Extension cable, plug and

socket must be of watertight construction

and intended for outdoor use.

The connections (plugs and sockets) should be kept dry and

off the ground.

For increased electrical safety use a Residual Current Device

(RCD) with a tripping current of not more than 30mA. Al-

ways check your RCD every time you use it.

If the supply cord is damaged, it must be replaced by a

Bosch Service Centre.

For products not sold in GB:

Warning: For your safety, it is required that the plug at-

tached to the product is connected with the extension cord.

The coupling of the extension cord must be protected

against splash water, be made of rubber or coated with rub-

ber. The extension cord must be used with a cable strain re-

lief.

Products sold in GB only:

Your product is fitted with an BS 1363/A approved electric

plug with internal fuse (ASTA approved to BS 1362).

If the plug is not suitable for your socket outlets, it should be

cut off and an appropriate plug fitted in its place by an au-

thorised customer service agent. The replacement plug

should have the same fuse rating as the original plug.

The severed plug must be disposed of to avoid a possible

shock hazard and should never be inserted into a mains

socket elsewhere.

u Products that are only sold in AUS and NZ: Use a resid-

ual current device (RCD) with a nominal residual current

of 30 mA or less.

Operation

u To prevent damage to the appliance, do not allow it to

operate dry.

Starting

Attach water supply hose (not supplied) to the mains water

supply and machine.

Connect the product to the mains supply ensuring that the

mains switch is in the off position.

Open water tap.

Press the safety lock (back button on the gun handle) to re-

lease the trigger. Fully press the trigger until there is a con-

stant flow of water to clear the air from the machine and wa-

ter supply hose. Release trigger. Press the safety lock (front

button on the gun handle).

Turn button on main switch. Point the power gun down-

wards. Press the trigger safety lock to release the trigger.

Fully press the trigger.

Autostop Function

The machine is designed to switch off the motor when the

trigger is released on the gun.

Bosch Power Tools F 016 L81 693 | (10.01.2019)

Bosch AdvancedAquatak 140 (06008A7D00) [17/294] For your safety

Содержание

Похожие устройства