Indesit SISL 106 [2/60] Installation

Indesit SISL 106 [2/60] Installation
2
GB
A
Installation
This instruction manual should be kept in a safe
place for future reference. If the appliance is sold,
transferred or moved, make sure that the instruction
manual remains with the machine so that the new
owner is able to familiarise himself/herself with its
operation and features.
Read these instructions carefully: they contain vital
information relating to the safe installation and
operation of the appliance.
Unpacking and levelling
Unpacking
1. Unpack the washing machine.
2. Make sure that the machine has not been
damaged during the transportation process. If it has
been damaged, contact the retailer and do not
proceed any further with the installation process.
3. Remove the 4
protective screws (used
during transportation)
and the rubber washer
with the corresponding
spacer, located on the
rear part of the appliance
(see figure).
4. Close off the holes using the plastic plugs
provided.
5. Keep all the parts in a safe place: they will be
needed again if the washing machine is moved to
another location.
Packaging materials should not be used as toys for
children.
Levelling
Your machine may make a considerable amount of
noise if the two front feet have not been adjusted
correctly.
1. Install the washing machine on a flat and sturdy
floor, without placing it against walls, cabinets or
other furniture.
2. If the floor is not
perfectly level, compen-
sate for any unevenness
by tightening or loosening
the adjustable front feet
(see figure); the angle of
inclination, measured in
relation to the worktop,
must not exceed 2°.
Levelling the machine correctly will provide it with
stability, help to avoid vibrations and excessive noise
and prevent it from shifting while it is operating. If it is
placed on carpet or a rug, adjust the feet in such a
way as to allow a sufficient ventilation space
underneath the machine.
Connecting the electricity and water
supplies
Connecting the water inlet hose
1. Insert seal A into the
end of the inlet hose and
screw the latter onto a
cold water tap with a 3/4
gas threaded opening
(see figure).
Before performing the
connection, allow the
water to run freely until it
is perfectly clear.
2. Connect the inlet hose
to the machine by
screwing it onto the cold
water inlet of the
appliance, which is
situated on the top right-
hand side of the rear part
of the appliance(see
figure).
3. Make sure that the hose is not folded over or bent.
The water pressure at the tap must fall within the
values indicated in the Technical details table (see
next page).
If the inlet hose is not long enough, contact a
specialised shop or an authorised technician.

Содержание

Installation This instruction manual should be kept in a safe place for future reference If the appliance is sold transferred or moved make sure that the instruction manual remains with the machine so that the new owner is able to familiarise himself herself with its operation and features Levelling the machine correctly will provide it with stability help to avoid vibrations and excessive noise and prevent it from shifting while it is operating If it is placed on carpet or a rug adjust the feet in such a way as to allow a sufficient ventilation space underneath the machine Read these instructions carefully they contain vital information relating to the safe installation and operation of the appliance Connecting the electricity and water supplies Unpacking and levelling Unpacking 1 Unpack the washing machine 2 Make sure that the machine has not been damaged during the transportation process If it has been damaged contact the retailer and do not proceed any further with the installation process 3 Remove the 4 protective screws used during transportation and the rubber washer with the corresponding spacer located on the rear part of the appliance see figure 4 Close off the holes using the plastic plugs provided 5 Keep all the parts in a safe place they will be needed again if the washing machine is moved to another location Packaging materials should not be used as toys for children Levelling Your machine may make a considerable amount of noise if the two front feet have not been adjusted correctly 1 Install the washing machine on a flat and sturdy floor without placing it against walls cabinets or other furniture 2 If the floor is not perfectly level compen sate for any unevenness by tightening or loosening the adjustable front feet see figure the angle of inclination measured in relation to the worktop must not exceed 2 2 Connecting the water inlet hose 1 Insert seal A into the end of the inlet hose and screw the latter onto a cold water tap with a 3 4 gas threaded opening see figure Before performing the connection allow the water to run freely until it is perfectly clear 2 Connect the inlet hose to the machine by screwing it onto the cold water inlet of the appliance which is situated on the top right hand side of the rear part of the appliancefsee figure 3 Make sure that the hose is not folded over or bent The water pressure at the tap must fall within the values indicated in the Technical details table see next page Ilf the inlet hose is not long enough contact a specialised shop or an authorised technician

Скачать
Случайные обсуждения