Metabo PE 15-20 RT Automotive (615200000) Инструкция по эксплуатации онлайн [15/96] 503474
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Metabo PE 15-20 RT Automotive (615200000) Инструкция по эксплуатации онлайн [15/96] 503474

Metabo PE 15-20 RT Automotive (615200000) Инструкция по эксплуатации онлайн [15/96] 503474
ENGLISH en
15
the machine does not start up. Switch the machine
off and back on again.
Use only genuine Metabo accessories.
Use only accessories that fulfil the requirements
and specifications listed in these operating
instructions.
See page 4.
A Hook and loop backing pad (for attaching
polishing and sanding accessories)
B Hook and loop polishing pad, coarse (for
buffing weathered paint)
C Hook and loop polishing pad, fine (for polishing
paint)
D Hook and loop polishing felt, soft (for buffing
paint,ferrous metals and stainless steel sheets)
E Hook and loop lambswool polishing disc (for
buffing weathered paint)
F Cushioning disc with Velcro fasteners (for
sanding curved surfaces)
G Felt polishing disc with internal thread M 14
H Plastic disc brushes
For a complete range of accessories, see
www.metabo.com or the catalogue.
Repairs to electrical tools must ONLY be
carried out by qualified electricians!
A defective mains cable must be replaced only with
a special, original mains cable from metabo
available from the Metabo service.
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. See
www.metabo.com for addresses.
You can download a list of spare parts from
www.metabo.com.
Observe the national regulations on
environmentally compatible disposal and on the
recycling of disused tools, packaging and
accessories.
Only for EU countries: never dispose of
power tools in your household waste! Used
power tools must be collected separately and
handed in for environmentally compatible recycling
in accordance with European Directive 2002/96/EC
on waste electrical and electronic equipment and its
implementation in national legal systems.
Explanatory notes on the specifications on page 3.
Subject to change in accordance with technical
progress.
D
max
=maximum support plate diameter
M
t, max
=maximum torque
M =Spindle thread
l =Length of the sanding spindle
n* =No-load speed (maximum speed)
n
S
=No-load speed depending on the thumb-
wheel position
n
N
* =Speed at rated load
P
1
=Rated input power
P
2
=Power output
m =Weight without mains cable
Measured values determined in conformity with
EN 60745.
Machine in protection class II
~ AC power
* Energy-rich, high-frequency interference can
cause fluctuations in speed. The fluctuations
disappear, however, as soon as the interference
fades away.
The technical specifications quoted are subject to
tolerances (in compliance with the relevant valid
standards).
Emission values
These values make it possible to assess the
emissions from the power tool and to compare
different power tools. The actual load may be higher
or lower depending on the operating conditions, the
condition of the power tool or the accessories.
Please allow for breaks and periods when the load
is lower for assessment purposes. Arrange
protective measures for the user, such as
organisational measures based on the adjusted
estimates.
Vibration total value (vector sum of three directions)
determined in accordance with EN 60745:
a
h, P
=Vibration emission value (polishing)
a
h, DS
=Vibration emission value (sanding
surfaces)
K
h,P
/K
h,DS
=Uncertainty (vibration)
Typical A-effective perceived sound levels:
L
pa
=Sound-pressure level
L
WA
=Acoustic power level
K
pA
, K
WA
= Uncertainty
The noise level can exceed 80 dB(A) during
operation.
Wear ear protectors!
11. Accessories
12. Repairs
13. Environmental Protection
14. Technical Specifications

Похожие устройства

Скачать