![Dewalt D25313K [12/16] Fitting a chuck adapter and chuck sold separately](/img/pdf.png)
Dewalt D25313K [12/16] Fitting a chuck adapter and chuck sold separately
![Dewalt D25313K [12/16] Fitting a chuck adapter and chuck sold separately](/views2/1635767/page12/bgc.png)
ENGLISH
10
3. Rotate the side handle to the desired position
and tighten the handle.
Setting the Drilling Depth (fig. 5)
1. Insert the required drill bit as described above.
2. Press the depth stop clamp (j) and keep it
depressed.
3. Fit the depth adjustment rod (h) through the
hole in the depth stop clamp.
4. Adjust the drilling depth as shown.
5. Release the depth stop clamp.
Forward/reverse Slider (fig. 6)
1. Push the forward/reverse slider (c) to the
LH-side for forward (RH) rotation. See arrows
on tool.
2. Push the forward/reverse slider (c) to the
RH-side for reverse (LH) rotation.
WARNING: Always wait until the motor
has come to a complete standstill
before changing the direction of rotation.
Fitting a Chuck Adapter and Chuck
(Sold Separately)
1. Screw a chuck onto the threaded end of the
chuck adapter.
2. Insert the connected chuck and adapter in the
tool as though it were a standard SDS Plus
®
bit.
3. To remove the chuck, proceed as for removing
a standard SDS Plus
®
bit.
WARNING: Never use standard chucks
in the hammerdrilling mode.
Consult your dealer for further information on the
appropriate accessories.
Replacing the Tool Holder with the
Chuck (fig. 1)
D25324
1. Turn the locking collar (k) into the unlocking
position and pull the tool holder/locking sleeve
(f) off.
2. Push the chuck (l) onto the spindle and turn the
locking collar into the locking position.
3. To replace the chuck with the tool holder, first
remove the chuck the same way as the tool
holder was removed. Then place the tool holder
the same way as the chuck was placed.
WARNING: Never use standard chucks
in the hammerdrilling mode.
Replacing the Dust Cover (fig. 3)
The dust cover (g) prevents dust ingress into the
mechanism. Replace a worn dust cover immediately.
1. Pull back the tool holder locking sleeve (f) and
pull the dust cover (g) off.
2. Fit the new dust cover.
3. Release the tool holder locking sleeve.
OPERATION
Instructions for Use
WARNING:
• Always observe the safety instructions
and applicable regulations.
• Be aware of the location of pipework
and wiring.
• Apply only a gentle pressure to
the tool (approx. 5 kg). Excessive
force does not speed up drilling but
decreases tool performance and may
shorten tool life.
• Do not drill or drive too deep to
prevent damage to the dust cover.
• Always hold the tool firmly with both
hands and ensure a secure stance
(fig. 7). Always operate the tool with
the side handle properly mounted.
Proper Hand Position (fi g. 1, 7)
WARNING: To reduce the risk of
serious personal injury, ALWAYS use
proper hand position as shown.
WARNING: To reduce the risk of
serious personal injury, ALWAYS hold
securely in anticipation of a sudden
reaction.
Proper hand position requires one hand on the side
handle (i), with the other hand on the main handle
(m).
Overload Clutch
If the drill bit becomes jammed or caught, the drive
to the drill spindle is interrupted by the overload
clutch. Because of the forces that occur as a result,
always hold the machine securely with both hands
and take a firm stance.
Switching On and Off (fig. 1)
1. To run the tool, press the variable speed switch
(a). The pressure exerted on the variable speed
switch determines the tool speed.
Содержание
- Congratulations 6
- Heavy duty rotary hammerdrill d25313 d25223 d25323 d25324 6
- Technical data 6
- Defi nitions safety guidelines 7
- Ec declaration of conformity 7
- General power tool safety warnings 7
- Save all warnings and instructions for future reference 7
- Additional specifi c safety rules for rotary hammers 9
- Markings on tool 9
- Package contents 9
- Residual risks 9
- Description fi g 1 10
- Electrical safety 10
- Mains plug replacement u k ireland only 10
- Using an extension cable 10
- Accessories fig 3 11
- Assembly and adjustments 11
- Fitting the side handle fig 4 11
- Indexing the chisel position fi g 2 11
- Inserting and removing sds plu 11
- Selecting the operating mode fig 2 11
- Fitting a chuck adapter and chuck sold separately 12
- Forward reverse slider fig 6 12
- Instructions for use 12
- Operation 12
- Overload clutch 12
- Proper hand position fi g 1 7 12
- Replacing the dust cover fig 3 12
- Replacing the tool holder with the chuck fig 1 12
- Setting the drilling depth fig 5 12
- Switching on and off fig 1 12
- Chipping and chiselling fig 1 13
- Drilling with a core bit fig 1 13
- Hammerdrilling fig 1 13
- Maintenance 13
- Rotary drilling fig 1 13
- Screwdriving fig 1 13
- Cleaning 14
- Lubrication 14
- Motor brushes 14
- Optional accessories 14
- Protecting the environment 14
- Guarantee 15
- N079517 07 10 16
- Türkiye 16
- Ελλάς 16
Похожие устройства
- Dewalt DW343K Инструкция по эксплуатации
- Dewalt DW331K Инструкция по эксплуатации
- Bosch GST 850 BE Professional Инструкция по эксплуатации
- Nilfisk MC 3C-170/820 Инструкция по эксплуатации
- Husqvarna 135 (9667618-04) Инструкция по эксплуатации
- Ada 6D Maxliner Инструкция по эксплуатации
- RedTrace M912SL Инструкция по эксплуатации
- Энкор Корвет-2 Инструкция по эксплуатации
- Champion C2000 220V Инструкция по эксплуатации
- Europower EP7000 Руководство пользователя
- Europower EP6500T Инструкция по эксплуатации
- Europower EP6000 Инструкция по эксплуатации
- Энкор Корвет-46 Инструкция по эксплуатации
- Wester 990-003 горелка Инструкция по эксплуатации
- Thermex ULTRA SLIM IU 50V (SpT070828) Инструкция по эксплуатации
- Thermex ULTRA SLIM IU 30V (SpT070826) Инструкция по эксплуатации
- Thermex Round Plus Floor IR 200 V (SpT068697) Инструкция по эксплуатации
- Энкор Корвет-104 Инструкция по эксплуатации
- Bosch GEX 125-1 AE L-BOXX (0601387503) Инструкция по эксплуатации
- Энкор РЭ-1200/110Э Инструкция по эксплуатации